Sony Projector VPL-DX146 User Manual

							41Indicators
Others
BOthers
Indicators
The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table 
below.
ON/STANDBY indicator
LAMP/COVER indicator
StatusMeaning/Remedies
Lights in red The projector is in Standby mode.
Flashes in green  The projector is ready to operate after having been turned on. 
 The lamp cools after the projector is turned off.
Lights in green The projector’s power is on.
Lights in orange The projector is in With No Input (Lamp Cutoff). (page 25)
Flashes in red The projector is in abnormal status. Symptoms are indicated by 
number of flashes. Address the problem in accordance with the 
following. If a symptom persists, despite having taken measures 
below, consult with qualified Sony personnel.
Flashes twice The internal temperature is unusually high. Check the items below.
 Check if nothing is blocking the ventilation holes. (pages 4, 4)
 Check if the air filter is not clogged. (page 47)
 Check if the Installation Attitude in the Installation menu is set 
correctly. (page 27)
Flashes six times Unplug the AC power cord from a wall outlet. After checking that the 
ON/STANDBY indicator goes out, plug the power cord to a wall 
outlet again then turn on the projector.
Other number of 
flashesConsult with qualified Sony personnel.
StatusMeaning/Remedies
Flashes in red Symptoms are indicated by number of flashes. Address the problem in 
accordance with the following.
Flashes twice  The lamp cover is not attached securely. (page 45)
Flashes three times The temperature of lamp is unusually high. Turn off the power and 
wait for lamp to cool then turn on the power again. If the symptom is 
shown again, the lamp may be burnt out. In this case, replace the lamp 
with a new one (page 45). 
						

							42Messages List
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessagesMeaning/RemedyPage
High temp.! Lamp off in 
1 min.Check the items below.
 Check if nothing is blocking the ventilation holes.
 Check if the air filter is not clogged.
 Check if the Installation Attitude in the Installation menu is 
set correctly.4, 4, 
27, 47
Frequency is out of 
range!Change the output setting of the connected equipment to one 
for signals supported by the projector.52
Please check Input-A 
Signal Sel.Set “Input-A Signal Sel.” to “Auto” or select the input signal 
type to suit to the input signal.25
Please clean the filter. Clean the air filter. 47
Please replace the Lamp 
and clean the Filter.Replace the lamp with a new one and clean the air filter. The 
message appears whenever you turn on the power until you 
replace the lamp and reset the lamp timer.45, 47
Projector temperature is 
high. High Altitude 
Mode should be “On” if 
Projector is being used 
at high altitude.When not using the projector at an altitude of 1,500 m or 
higher, check the items below.
 Check if nothing is blocking the ventilation holes.
 Check if the air filter is not clogged.
 Check if Installation Attitude in the Installation menu is set 
correctly.4, 4, 
27, 47
Not applicable! Invalid key was pressed. –
The control keys are 
locked!“Control Key Lock” is set to “On.” 24
Projector will shutdown 
soon
Press ?/1 Key to RestartThe ?/1 key was pressed and the projector will be shut down 
soon. To cancel shutdown, press the ?/1 key again (the 
projector will remain on). To turn off the projector directly, 
press and hold the ?/1 key for a few seconds.16
Lamp Dimming Reduces lamp output when “With Static Signal” is set. When 
any change in signal is detected, or an operation (remote 
control or control panel) is performed, normal brightness is 
restored.25 
						

							43Troubleshooting
Others
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the 
instructions below.
SymptomsRemedyPage
The power is not turned 
on.Check if the AC power cord is firmly connected. –
When the “Control Key Lock” is set to “On,” you cannot turn 
on the projector using the ?/1 key on the projector.24
If the lamp or lamp cover is not attached securely, the projector 
cannot be turned on.45
No image. Check if the connecting cable is connected to external 
equipment firmly.8
Check the computer signal is set for output to an external 
monitor only. If you set your computer to output to both the 
computer’s display and an external monitor, the external 
monitor image may not be displayed properly. Set your 
computer to output to only an external monitor.12
Check if the application “USB Display” or “Projector Station 
for Network Presentation” is running. 33, 36
Check if the USB memory device connected to the projector is 
compatible with the projector.37
Check if the input source is correctly selected. 12
Check if the picture is muted. 6
The application “USB 
Display” or “Projector 
Station for Network 
Presentation” does not 
start.Check if the computer connected to the projector meets the 
system requirement for the applications. 33, 36
The computer cannot 
connect to the projector.  Check “LAN Settings” of the projector.
 Check the condition of the wireless connection. 25
On-screen display does 
not appear.The on-screen display does not appear when “Status” in the 
Operation menu is set to “Off.”24
The aspect ratio of the 
display is not right/the 
image is displayed 
smaller /a portion of 
image does not appear.The image may not display correctly because the input signal 
cannot be judged correctly. In this case, set “Aspect” manually.6, 19, 
21
The image is a 
trapezoid.The images become trapezoidal because of the projection 
angle. In this case, you can correct the trapezoidal distortion, 
using a Keystone feature.6, 15, 
27
When the “V Keystone” is set to “Manual,” the keystone 
feature does not work automatically. Set “V Keystone” to 
“Auto” or “Manual” to set manually.6, 15, 
27
When the projector is installed on an uneven surface, the 
keystone feature may not work properly. In this case, select 
“Manual” to set “V Keystone” manually.6, 15, 
27 
						

							44Troubleshooting
The image is dark/too 
bright.The settings for “Brightness,” “Contrast,” and “Lamp Mode” 
affect brightness of the image. Check if the value is 
appropriate.18, 25
The image will be dark when the lamp is burnt out. Check 
“Lamp Timer,” and replace the lamp with a new one if 
necessary.28, 45
“With Static Signal” is set to “On.”  25
During picture muting, the lamp is dimmed to reduce power 
consumption. 25
When video signal is not input, the lamp is dimmed to reduce 
power consumption.–
The image becomes 
darker or brighter.When the lamp is dimmed for a long time, brightness may 
increase temporarily, but this is not malfunction.–
When the “Lamp Mode” is set to “Auto,” the luminance of the 
lamp changes according to the input image.25
The image is not clear. Check if the projector is in focus. 13
The picture will not be clear if condensation has accumulated 
on the lens. In this case, let the projector sit for about two 
hours with the power on.–
The image is noisy. Check if the connecting cable is connected to the external 
equipment properly.8
No sound. Check that the connecting cables between the projector and 
external video or audio equipment are securely connected.8
Check if the external audio equipment is set properly. –
Audio is not output if audio muting is activated. 6
Check if the volume is not set to minimum. 6, 23
The remote commander 
does not work.Check if the batteries are installed correctly. –
Check if the batteries are not exhausted. –
The fan is noisy. The sound from the fan is often greater than normal to cool the 
lamp, etc. in the following cases.
 “Lamp Mode” is set to “High.”
 The unit is used at a high altitude. “High Altitude Mode” is 
set to “On.”
 The unit is used in the location where the temperature is high.25, 27
If the ventilation holes are blocked, the internal temperature of 
the projector rises and the fan noise becomes larger.4, 4
SymptomsRemedyPage 
						

							45Replacing the Lamp
Others
Replacing the Lamp
Replace the lamp with a new one if a message displayed on the projected image (page 42).
Use an LMP-D213 projector lamp (not supplied) for replacement.
 The lamp remains hot after the projector is 
turned off. If you touch the lamp, you may 
burn your finger. When you replace the 
lamp, wait for at least an hour after 
turning off the projector for the lamp to 
cool sufficiently.
 Do not allow any metallic or inflammable 
objects into the lamp replacement slot after 
removing the lamp, otherwise it may cause 
electrical shock or fire. Do not put your 
hands into the slot.
If the lamp breaks, contact qualified 
Sony personnel. Do not replace the lamp 
yourself.
 When removing the lamp, be sure to pull it 
out straight, by holding the designated 
location. If you touch a part of the lamp other 
than the designated location, you may be 
burned or injured. If you pull out the lamp 
while the projector is tilted, the pieces may 
scatter if the lamp breaks any may cause 
injury.
1Turn off the projector, and disconnect 
the AC power cord from a wall outlet.
2When the lamp has cooled 
sufficiently, open the lamp cover by 
loosening one screw. 
For safety reasons, do not loosen any other 
screws.
3Loosen the two screws on the lamp 
unit (1). Fold out the handle (2), 
then pull out the lamp unit by the 
handle (3).
Caution
Notes
Note
1
12
3
Fold out the handle. 
						

							46Replacing the Lamp
Do not put your hands into the lamp 
replacement slot, and do not allow any 
liquid or other objects into the slot to avoid 
electrical shock or fire.
4Insert the new lamp all the way in until 
it is securely in place (1). Tighten the 
two screws (2). Fold down the handle 
to replace it (3).
 Be careful not to touch the glass surface 
of the lamp and a inside conductor.
 Insert the handle firmly to attach it 
securely.
 The power will not turn on if the lamp is 
not secured properly.
5Close the lamp cover and tighten the 
1 screw.
6Connect the AC power cord to a wall 
outlet and turn on the projector.
7Reset the lamp timer for notification of 
the next replacement time.
Select “Lamp Timer Reset” on the 
Function menu then press the ENTER 
key. When a message appears, select 
“Yes” to reset the lamp timer (page 23).
Disposal of the used lamp
For the customers in the USA
Lamp in this product contains mercury. 
Disposal of these materials may be 
regulated due to environmental 
considerations. For disposal or 
recycling information, please contact 
your local authorities or the 
Telecommunications Industry 
Association (www.eiae.org).
Caution
Notes
1
2
2
3
Fold down the handle.
Caution 
						

							47Cleaning the Air Filter
Others
Cleaning the Air Filter
When a message appears on the projected image indicating time for a filter cleaning, clean the 
air filter (page 42).
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with 
a new one. For details on purchasing/fitting a new air filter, consult with the store where you 
purchased the projector, or contact qualified Sony personnel.
If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the 
temperature may rise inside the unit, leading to a possible malfunction or fire.
1Turn off the projector, and disconnect 
the AC power cord from the AC outlet.
2Slide out and remove the air filter 
cover from the unit.
3Clean the air filter with a vacuum 
cleaner.
Pull out and remove the air filter, and 
clean it with a vacuum cleaner.
4Reattach the air filter cover to the unit.
Install the air filter with its open weave side 
facing the bottom of the unit, then place the 
air filter cover back in the unit.
Caution
Air filter cover
Note
Claws
Air filter 
						

							48Specifications
Specifications
ItemsDescriptions
ModelVPL-DX146/DX126/VPL-DW126
Projection system 3 LCD system
Display device Effective display 
sizeVPL-DX146/DX126: 0.63 inch (16.0 mm), 
3 plate panels, Aspect ratio 4:3
VPL-DW126: 0.59 inch (15.0 mm), 3 plate panels, 
Aspect ratio 16:10
Effective picture 
elementsVPL-DX146/DX126: 2,359,296 pixels (1024 × 768 
pixels, 3 plate panels)
VPL-DW126: 3,072,000 pixels (1280 × 800 pixels, 
3 plate panels)
Projection lens Zoom Manual zoom: 
VPL-DX146/VPL-DW126: approx.1.3 times
VPL-DX126: approx.1.2 times
Focus Manual
Light source High-pressure mercury lamp, 210 W type
Projected image 
size30 inches to 300 inches (0.76 m to 7.62 m)
Luminous flux 
(Brightness)VPL-DX146: 3200 lm
VPL-DX126/VPL-DW126: 2600 lm
(when “Lamp Mode” is set to “High”)
Speaker 1 W × 1 (monaural)
Applicable 
scanning 
frequency
*1
Horizontal: 15 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz
Resolution
*1When a computer 
signal is inputMaximum display resolution: 1600 × 1200 pixels (resize)
Panel display resolution: 
VPL-DX146/DX126: 1024 × 768 pixels
VPL-DW126: 1280 × 800 pixels
When a video 
signal is inputNTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p, 
576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i, 
1080/60p, 1080/50p
Color system NTSC
3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N 
						

							49Specifications
Others
INPUT OUTPUT 
(Computer/video)INPUT ARGB/YPBPR input connector: Mini D-sub 15 pin 
female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 
75 ohms terminated, RGB/P
BPR: 0.7 Vp-p ± 2 dB, 
75 ohms terminated, Sync signal: TTL level high 
impedance, positive/negative
Audio input connector: Stereo mini jack, rated input 
500 mVrms, input impedance more than 47 kohms
INPUT BHDMI input connector: HDMI 19-pin, HDCP, HDMI 
audio support
VIDEOVideo input connector: Pin jack, 1 Vp-p ± 2 dB, sync 
negative, 75 ohmes terminated
Audio input connector: Shared with INPUT A
Other connectorsLAN connector: RJ45, 10BASE-T/100BASE-TX
USB connector: Type A
USB connector: Type B
Operating 
temperature/
Operating 
humidity0 °C to 35 °C (32 °F to 95 °F)/20% ~ 80% (no 
condensation)
Storage 
temperature/
Storage humidity–10 °C to +60 °C (14 °F to 140 °F)/20% to 80% (no 
condensation)
Power 
requirements100V to 240V AC, 3.0 - 1.2 A, 50/60Hz
Power 
consumptionVPL-DX146:
100V to 120V AC: 291W
220V to 240V AC: 279W
VPL-DX126:
100V to 120V AC: 290W
220V to 240V AC: 278W
VPL-DW126:
100V to 120V AC: 294W
220V to 240V AC: 280W
Standby power100V to 120V AC: 5.7W (when “Standby mode” is set to 
“Standard”)/0.4W(when “Standby mode” is set to 
“Low”)
220V to 240V AC: 5.9W (when “Standby mode” is set to 
“Standard”)/0.5W(when “Standby mode” is set to 
“Low”)
Heat dissipation VPL-DX146:
100V to 120V AC: 992BTU
220V to 240V AC: 951BTU
 VPL-DX126:
100V to 120V AC: 991BTU
220V to 240V AC: 949BTU
VPL-DW126:
100V to 120V AC: 1004BTU
220V to 240V AC: 956BTU
ItemsDescriptions
ModelVPL-DX146/DX126/VPL-DW126 
						

							50Specifications
*1: For details, refer to “Acceptable Input Signals” on page 52.
*2: Information on accessories in this manual is current as of July 2013.
*3: Not all optional accessories are available in all countries and area. Please check with your local 
Sony Authorized Dealer.
Design and specifications of the unit, including the optional accessories, are subject to change 
without notice.Standard 
dimensions
(W/H/D)Approx. 315 × 87.2 × 233 mm (12 
13/32 × 3 7/16 × 9 3/16 
inches)
Approx. 315 × 75 × 230.5 mm (12 
13/32 × 2 15/16 × 
9 1/16 inches) (without projecting parts)
Mass Approx. 2.6 kg (5.8 lb)
Supplied 
accessoriesSee “Checking the Supplied Accessories” in the supplied 
Quick Reference Manual.
Optional 
accessories
*2 *3Projector Lamp LMP-D213 (for replacement)
ItemsDescriptions
ModelVPL-DX146/DX126/VPL-DW126
Notes
 Always verify that the unit is operating properly before use. SONY WILL NOT BE 
LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, 
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF 
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER 
DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE 
WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
 SONY WILL NOT BE LIABLE FOR CLAIMS OF ANY KIND MADE BY USERS OF 
THIS UNIT OR MADE BY THIRD PARTIES.
 SONY WILL NOT BE LIABLE FOR THE TERMINATION OR DISCONTINUATION 
OF ANY SERVICES RELATED TO THIS UNIT THAT MAY RESULT DUE TO 
CIRCUMSTANCES OF ANY KIND.
Notes
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND RESULTING FROM A 
FAILURE TO IMPLEMENT PROPER SECURITY MEASURES ON TRANSMISSION 
DEVICES, UNAVOIDABLE DATA LEAKS RESULTING FROM TRANSMISSION 
SPECIFICATIONS, OR SECURITY PROBLEMS OF ANY KIND.