Sony Kdl 60nx810 Operating Instructions

							11
Setting up your TV
Shown with HD BRAVIA® Sync™ Basic Connection
Shown with HD Basic Connection with Home Theater System
VIDEO
OUTCOMPONENT
VIDEO OUTDIGITAL OUTPCM/DTS/DOLBY DIGITAL5.1CH OUTPUTVIDEOY
L
RAUDIO
OUTL
RWOOFERCOAXIAL OPTICALFRONT REAR CENTER
S VIDEOHDMI
OUTAC INPB/CBPR/CR
OPT INSATOPT INVIDEO 1COAX IN AUDIO INDV D
DVD IN SAT IN VIDEO 2/BD IN OUT
AUDIO INAUDIO INFRONT R
AM
RLRL
FRONT LSUR RSUR LCENTERSUBWOOFER
*Rear of TV
*Blu-ray Disc
HD Cable Box or 
HD Satellite Receiver*A/V Receiver
* Signifies a BRAVIA Sync capable device. SAT 
(Dish)
Cable/
Antenna
Rear of TV
Cable/
Antennaor Blu-ray Disc/DVD
SD Cable Box or
SD Satellite Receiver Cable/SAT (Dish)
Home Theater SystemSide Panel
(Continued)
 
						

							12
Shown with PC Connection with SD VCR/DVD
Rear of TVSide Panel
PC
DVD VCR Splitter
Cable/AntennaVCR/DVD ComboNotebook PC or
 
						

							13
Setting up your TV
Securing the TV
Sony strongly recommends 
taking measures to prevent 
the TV from toppling over.
Unsecured TVs may topple 
and result in property 
damage, serious bodily 
injury or even death.
Preventing the TV from 
Toppling
 Secure the TV to a wall and/or stand.
 Do not allow children to play or climb on 
furniture and TV sets.
 Avoid placing or hanging items on the 
TV.
 Never install the TV on:
–slippery, unstable and/or uneven 
surfaces.
–furniture that can easily be used as 
steps, such as a chest of drawers.
 Install the TV where it cannot be pulled, 
pushed, or knocked over.
 Route all AC power cords and 
connecting cables so that they are not 
accessible to curious children.
Recommended Measures to 
Secure the TV
Consider the following measures when 
securing your TV to a TV stand (not 
supplied).
1Secure the Stand for the TV.
Make sure the TV stand can adequately 
support the weight of the TV. Use two angle 
braces (not supplied) to secure the stand. 
For each angle brace use the appropriate 
hardware to:
 Attach one side of the angle brace to the 
wall stud.
 Attach the other side to the TV stand.
2Secure the TV to the Stand.
Use the optional hardware listed below (not 
supplied):
 A machine screw (screwed into the TV’s 
Table-Top Stand)
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
Use M4 × 16 screw
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and 
KDL-46/40NX710
Use M4 × 8 screw
 A screw or similar (attach it to the TV 
stand)
 Rope or chain (strong enough to support 
the weight of the TV). Make sure that 
there is no excess slack in the rope or 
chain.
An alternative way to secure the TV is with 
an optional Sony Support Belt Kit.
Stand Angle brace 
(not supplied)
Machine screw 
(not supplied)
Screw (not supplied) Screw hole on the 
Table-Top Stand
Rope or chain 
(not supplied)
(Continued)
 
						

							14
~
Contact Sony Customer Support to obtain the 
optional Support Belt Kit by providing your TV 
model name.
For United States call: 1-800-488-7669 or 
visit: www.sony.com/accessories
For Canada call: 1-877-899-7669
3Anchor the TV to the Wall.
Anchor the TV to the wall by using bolts, 
wall anchor and chain (or rope).
~
KDL-60NX801, KDL-60/52/46NX800 and 
KDL-46/40NX700 are shipped with screws 
attached to the rear of the TV. (They are 
fastened in the screw holes for wall mounting.) 
Be sure to remove the upper two screws prior 
to anchoring the TV on a wall.
Securing the TV to the stand without securing 
the TV and the stand to the wall provides 
minimum protection against the TV toppling 
over. For further protection, be sure to follow 
the three measures recommended.
Organizing the AC power 
cord
~
Do not bundle the AC power cord together 
with other cables.
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
~
After the AC power cord is thread as 
illustrated, place the bottom cover (for NX801/
800 series only).
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and 
KDL-46/40NX710Anchor bolts (not supplied)
Wall-
mount 
holesRope or 
chain 
(not 
supplied)
Wall-anchor 
(not 
supplied)
 
						

							15
Setting up your TV
Running initial setup
1Complete your cable connections 
before proceeding with the Initial 
Setup. 
Connect the TV to your nearest power 
outlet.
2Check the ENERGY SAVING 
SWITCH setting is on (z).
3Press 1 (POWER) on the TV.
When you switch the TV on for the 
first time, the Language menu 
appears on the screen.
~
The TV image shown here may differ from 
your TV but the operation of your TV remains 
the same as indicated.
4Follow the instructions on the screen.
~
The ENERGY SAVING SWITCH must be on 
(z) to set the clock and obtain program 
information for the TV Guide.
Home mode sets the TV to display the settings 
optimized for home viewing (this setting is 
ENERGY STAR compliant).
5Select Continue to scan for available 
channels and enable the TV Guide 
On Screen
® feature. If you receive 
channels from a cable box or satellite 
receiver and do not wish to use the 
TV’s built-in tuner, select Skip.
Selecting Skip will disable the TV 
Guide On Screen feature, which is 
only available when the TV’s tuner is 
used.
~
If you skip the channel scan while in the setup 
menus, TV Guide will be disabled.
Detaching the Table-Top 
Stand from the TV
Remove only the screws marked with   on 
the TV.
~
Do not remove the Table-Top Stand for any 
reason other than to install corresponding 
accessories on the TV.
For KDL-60NX801, KDL-60/52/
46NX800 and KDL-46/40NX700
~
The NX801/NX800/NX700 series models 
must remove the stand rear cover prior to 
detaching the Table-Top Stand.
When installing the TV on a wall, remove the 
four screws from the rear of the TV. (They are 
fastened in the screw holes for wall mounting.) 
Be sure to store the removed screws in a safe 
place, keeping them away from children 
(except KDL-46/40NX700).
When attaching the Table-Top Stand again, be 
sure to fasten the four screws (previously 
removed) to the original holes on the rear of 
the TV (except KDL-46/40NX700).
For KDL-55NX811, KDL-60/55/
46NX810, KDL-46/40NX711 and 
KDL-46/40NX710
KDL-60NX810
Joint
 
						

							16
Using a Wall-Mount Bracket
Your TV can be mounted on a wall using a 
Wall-Mount Bracket (not supplied) out of 
the box as packaged. Some larger size TV 
may require detaching the Table-Top Stand; 
see “Detaching the Table-Top Stand from 
the TV” (page 15). 
Prepare the TV for the Wall-Mount Bracket 
before making cable connections.
For product protection and safety 
reasons, Sony strongly recommends that 
you use the Wall-Mount Bracket 
designed for your TV and the installation 
should be performed by a Sony dealer or 
licensed contractor.
 Follow the instruction guide provided 
with the Wall-Mount Bracket for your 
model. Sufficient expertise is required in 
installing this TV, especially to 
determine the strength of the wall for 
withstanding the TV’s weight.
 Be sure to use the screws supplied with 
the Wall-mount bracket when attaching 
the mounting hooks to the TV set.
The supplied screws are designed so that 
they are 8 mm to 12 mm in length when 
measured from the attaching surface of 
the mounting hook.
The diameter and length of the screws 
differ depending on the Wall-mount 
bracket model. Use of screws other than 
those supplied may result in internal 
damage to the TV set or cause it to fall, 
etc.
 Be sure to store the unused screws and 
Table-Top Stand in a safe place until you 
are ready to attach the Table-Top Stand. 
Keep the screws away from small 
children.
~
Read the supplied Safety Booklet for 
additional safety information.
Installing the TV Against a 
Wall or Enclosed Area
Make sure that your TV has adequate 
ventilation. Allow enough space around the 
TV as shown below. Avoid operating the TV 
at temperatures below 41 °F (5 °C).
~
Inadequate ventilation can lead to overheating 
of the TV and may cause damage to your TV 
or cause a fire.
8-12 mm
Screw 
(supplied with the 
Wall-mount bracket)
Mounting Hook
Hook attachment on rear of 
TV set
(30 cm) 117/8 inches
(6 cm)            inches
4 inches
(10 cm)4 inches
(10 cm)23/8 
Leave at least this much space around the set.
Installed with stand
inches 117/8 
4 inches
(10 cm) 4 inches
(10 cm)
4 inches (10 cm)
(30 cm)
Installed on the wall
Leave at 
least this 
much space 
around the 
set.
Never install the TV set as follows:
Air circulation is blocked.Air circulation is blocked.
Wall Wall
 
						

							17
To watch TV
To watch TV
To watch programs
To use the TV features
Press HOME to display TV Home Menu/
XMB
™ to access TV Settings and other 
media and network related content.Press OPTIONS to display a list of 
convenient functions and menu shortcuts. 
The Options menu items vary based on 
current input and/or content.
1Turn on the TV.
1Check the ENERGY SAVING 
SWITCH setting is on (z).
2Press 1 (POWER) on the TV or 
TV ?/1 on the remote control to 
turn on the TV. (You may use the 
TV ?/1 button located on the 
back of the remote control.)
~
The TV image shown here may differ 
from your TV but the operation of your 
TV remains the same as indicated.
2Select a TV channel.
To use the Guide
Press GUIDE to display the TV Guide 
On Screen to view scheduled 
programs or to select a program to 
watch. Press again to exit the Guide. 
Use with 0-9 and ENT to select digital 
channels. For example, to enter 2.1, 
press , , , and ENT.
GUIDE
OPTIONS
HOME
0-9
ENT
2 1-
2
Settings
TVPicture & DisplayAdjust the picture and screen settingsPress      for:
Picture Adjustments
Ambient Sensor
Screen
Pro Picture Setup
Picture Adjustments
Sound Adjustments
Add to Favorites
Speakers
(Continued)
 
						

							18
To use i-Manual
xWelcome to i-Manual
xBRAVIA TV Features
xWatching TV
Introduces convenient features such as TV 
Guide, Favorites, etc.
xUsing the Home Menu
You can find how to customize your TV 
settings, etc.xFun Features with Connected 
Equipment
Introduces how to connect and enjoy 
optional equipment.
xParts Description
xTroubleshooting
You can find solutions for your problems.
xIndex
~
Images and illustrations may differ from what you are watching on this TV.
Your BRAVIA TV comes with an on-screen 
manual. You can browse your i-Manual 
anytime you need to find the varieties of 
convenient functions.
1Press i-MANUAL.
2Press F/f/G/g/  to navigate 
and select items.
1
2
Welcome to i-Manual
BRAVIA TV  Features
Watching TV
Using the Home Menu
Fun Features with Connected Equipment
Parts Description
Troubleshooting
Indexi-Manual
RETURNBack
 
						

							19
Additional Information
Additional Information
Troubleshooting
The TV will indicate any problems with the STANDBY indicator flashing in red.
When the STANDBY indicator is flashing
The self-diagnosis function is activated. 
1Count how many times the STANDBY indicator flashes between each three 
second break.
For example, the indicator may flash three times, go off for three seconds, then flash 
again three times.
2Press 1 (POWER) on the TV to turn it off, disconnect the AC power cord, and 
inform your dealer or Sony service center of how the indicator flashes (number 
of flashes).
When the STANDBY indicator is not flashing
1Check the items in the tables below. (Also refer to “Troubleshooting” in the 
i-Manual.)
2If the problem persists, contact Sony Customer Support (information provided 
on the front cover).
ConditionExplanation/Solution
Picture
There is no picture 
(screen is dark) and no 
sound.Check the antenna/cable connection.
Connect the TV to the AC power, and press 
1 (POWER) on 
the TV.
If the STANDBY indicator lights up in red, press TV 
?/1 
on the remote control.
Tiny black dots and/or 
bright dots appear on the 
screen.The screen is composed of pixels. Tiny black dots and/or 
bright dots (pixels) on the screen do not indicate a 
malfunction.
General
The TV’s power cannot 
be turned on.Check to see the (z) mark on the ENERGY SAVING 
SWITCH is pressed.
The TV turns off 
automatically (the TV 
enters standby mode).Check if the Sleep Timer, Timer, or Idle TV Standby is 
activated.
The Auto Shut-off function may be set to On. If Auto 
Shut-off is activated and TV receives no signal, the TV will 
automatically enter standby mode in 15 minutes. Check 
Auto Shut-off is activated under Eco feature of this TV.
(Continued)
 
						

							20
How to Care for Your BRAVIA
Safety is very important, please read and follow the safety documentation (Safety Booklet) 
separately provided.
Unplug the TV and other connected equipment from the 
wall outlet before you begin cleaning your TV.
 Wipe the LCD screen gently with a soft cloth.
 Stubborn stains may be removed with a cloth slightly 
moistened with a solution of mild soap and warm water.
 If using a chemically pretreated cloth, please follow the 
instruction provided on the package.
 Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
 Do not plug in the TV into the wall outlet until the moisture from cleaning has evaporated.
The TV should also be placed on a stable surface to prevent it from toppling over (see 
page 13). If you have young children or pets at home, check regularly to insure the TV is 
securely fastened. The remote does not 
function.Replace the batteries.
Your TV may be in SYNC mode. Press SYNC MENU, 
select TV Control and then select Home (Menu) or 
Options to control the TV.
The TV and its 
surrounding become 
warm.When the TV is used for an extended period of time, the TV 
and its surround may become warm to touch. This is not 
malfunction of the TV.
The Parental Lock 
password has been 
forgotten.Enter 4357 for the PIN code. (PIN code 4357 is always 
accepted.)
ConditionExplanation/Solution