Sony Kdl 46d3000 Operating Instructions

							© 2007 Sony Corporation
LCD Digital Colour TV
3-096-727-11(1)
U
Operating Instructions 
Before operating the TV, please read the “Safety 
information” section of this manual.
Retain this manual for future reference.
For useful information about Sony products 
KDL-46D3000/46D3010
KDL-40D3000/40D3010
KDL-32D3000/32D3010
 
						

							2 GB
Thank you for choosing this Sony product.
Before operating the TV, please read this manual 
thoroughly and retain it for future reference.
A moulded plug complying with BS1363 is fitted to this 
equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced with 
the same rating of fuse approved by ASTA or BSI to BS 1362 
(i.e., marked with   or  ) must be used.
When an alternative type of plug is used it should be fitted 
with the same rating of fuse, otherwise the circuit should be 
protected by a 13 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse 
cover, be sure to attach the fuse cover after you change the 
fuse. Never use the plug without the fuse cover. If you should 
lose the fuse cover, please contact your nearest Sony service 
station.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and 
replace the fuse.
Disposal of Old Electrical & 
Electronic Equipment 
(Applicable in the European 
Union and other European 
countries with separate 
collection systems)
This symbol on the product or on 
its packaging indicates that this 
product shall not be treated as 
household waste. Instead it shall 
be handed over to the applicable 
collection point for the recycling 
of electrical and electronic 
equipment. By ensuring this product is disposed of correctly, 
you will help prevent potential negative consequences for the 
environment and human health, which could otherwise be 
caused by inappropriate waste handling of this product. The 
recycling of materials will help to conserve natural 
resources. For more detailed information about recycling of 
this product, please contact your local Civic Office, your 
household waste disposal service or the shop where you 
purchased the product.• Any functions related to Digital TV ( ) will only work 
in countries or areas where DVB-T (MPEG2) digital 
terrestrial signals are broadcast or where you have access 
to a compatible DVB-C (MPEG2) cable service. Please 
confirm with your local dealer if you can receive a DVB-
T signal where you live or ask your cable provider if their 
DVB-C cable service is suitable for integrated operation 
with this TV. 
 The cable provider may charge an additional fee for such 
services and you may be required to agree to their terms 
and conditions of business.
 Although this TV set follows DVB-T and DVB-C 
specifications, compatibility with future DVB-T digital 
terrestrial and DVB-C digital cable broadcasts cannot be 
guaranteed.
 Some Digital TV functions may not be available in some 
countries/regions and DVB-C cable may not operate 
correctly with some providers.
For a list of compatible cable providers, refer to the support 
web site:
http://support.sony-europe.com/TV/DVBC
  is a registered trademark of the DVB Project
 HDMI, the HDMI logo and High-Definition Multimedia 
Interface are trademarks or registered trademarks of 
HDMI Licensing LLC.
The illustrations used in this manual are of the KDL-
40D3000 unless otherwise stated.
Introduction
NOTICE FOR CUSTOMERS IN THE 
UNITED KINGDOM
Disposal of the TV set
FUSE
Notice for Digital TV function
Trademark information
 
						

							3 GB
Table of Contents
Safety information ..................................................................................................................... 7
Precautions ............................................................................................................................... 8
Overview of the remote ..........................................................................................................9
Overview of the TV buttons and indicators ........................................................................ 10
Watching TV............................................................................................................................ 11
Checking the Digital Electronic Programme Guide (EPG)  .............................................. 13
Using the Digital Favourite list  ........................................................................................ 15
Connecting optional equipment............................................................................................... 16
Viewing pictures from the connected equipment .................................................................... 18
Using HDMI control ................................................................................................................. 19
Navigating through menus ...................................................................................................... 20
Picture menu ........................................................................................................................... 21
Sound menu ............................................................................................................................ 23
Screen menu ........................................................................................................................... 25
Set-up menu............................................................................................................................ 26
PC Settings menu ................................................................................................................... 30
Analogue Set-up menu ...........................................................................................................31
Digital Set-up menu  ........................................................................................................ 34
Specifications .......................................................................................................................... 37
Troubleshooting ...................................................................................................................... 39
Start-up Guide 4
Watching TV
Using Optional Equipment
Using MENU Functions
Additional Information
 : for digital channels only
 
						

							4 GB
Start-up Guide
1: Checking the 
accessories
Mains lead (Type BF)* (1)
Coaxial cable (1)
Support belt (1) and screws (2)
Remote RM-ED009 (1)
Size AA batteries (R6 type) (2)
* For models with ferrite cores, do not remove these cores.
To insert batteries into the remote
~ Observe the correct polarity when inserting batteries.
 Do not use different types of batteries together or mix old 
and new batteries.
 Dispose of batteries in an environmentally friendly way. 
Certain regions may regulate the disposal of batteries. 
Please consult your local authority.
 Handle the remote with care. Do not drop or step on it, or 
spill liquid of any kind onto it.
 Do not place the remote in a location near a heat source, a 
place subject to direct sunlight, or a damp room.
2: Connecting an aerial/
cable/VCR
Push and lift the cover to open.
Connecting an aerial/cable
Connecting an aerial/cable and VCR
Coaxial cable (supplied)
Mains lead (supplied)
Scart lead (not supplied)
VCR Mains lead
(supplied)
Coaxial cable
(not supplied)Coaxial cable
(supplied) Terrestrial signal or cable
Terrestrial signal
or cable
 
						

							5 GB
Start-up Guide3: Preventing the TV 
from toppling over
4: Bundling the cables
5: Performing the initial 
setup
1Connect the TV to your mains socket 
(220-240 V AC, 50 Hz).
2Press 1 on the top edge of the TV.
When you turn on the TV for the first time, the 
Language menu appears on the screen.
3Press F/f/G/g to select the language 
displayed on the menu screens, then press 
.
Selecting the language and country/
region
3,4,6,7
9
Continued
 
						

							6 GB
4Press F/f to select the country/region in 
which you will operate the TV, then press 
.
If the country/region which you want to use on the 
TV does not appear in the list, select “-” instead of 
a country/region.
5Before you start auto-tuning the TV, insert 
a pre-recorded tape into the VCR 
connected to the TV (page 4) and start play 
back.
The video channel will be located and stored on 
the TV during auto-tuning.
If no VCR is connected to the TV, skip this step.
6Press G/g to select “OK”, then press  .
7Press F/f to select “Antenna” or “Cable”, 
then press  .
If you select “Cable”, the screen for selecting the 
scan type appears. See “To tune the TV for digital 
cable connection” on page 6.
The TV starts searching for all available digital 
channels, followed by all available analogue 
channels. This may take some time, so do not 
press any buttons on the TV or remote while 
proceeding.
If a message appears for you to confirm the aerial 
connection
No digital or analogue channels were found. 
Check all the aerial connections and press   to 
start auto-tuning again.
8When the Programme Sorting menu 
appears on the screen, follow the steps of 
“Programme Sorting” on page 31.
If you do not wish to change the order in which the 
analogue channels are stored on the TV, go to next 
step.
9Press MENU to exit.
The TV has now tuned in all the available 
channels.
~When a digital broadcast channel cannot be received, or 
when selecting a region in which there are no digital 
broadcasts in step 4 (page 6), the time must be set after 
performing step 9.
To tune the TV for digital cable connection
1Press F/f to select “Scan Type”, then 
press .
2Press F/f to select “Quick Scan” or “Full 
Scan”, then press  .
“Quick Scan”: Channels are tuned according to 
the cable provider’s information within the 
broadcast signal. The recommended setting for 
“Frequency”, “Network ID” and “Symbol Rate” is 
“Auto”. “Quick Scan” is recommended for fast 
tuning when this is supported by your cable 
provider.
“Full Scan”: All available channels are tuned and 
stored. This procedure may take some time. This 
option is recommended when “Quick Scan” is not 
supported by your cable provider.
For further information about supported cable 
providers, refer to the support web site:
http://support.sony-europe.com/TV/DVBC
3Press G/g/f to select “Start”.
The TV starts searching for channels. Do not press 
any buttons on the TV or remote.
~Some cable providers do not support “Quick Scan”. If no 
channels are detected using “Quick Scan”, perform “Full 
Scan”.
Detaching the Table-
Top Stand from the TV
~Do not remove the Table-Top Stand for any reason other than 
to wall-mount the TV.
Auto-tuning the TV
 
						

							7 GB
Safety information
Installation/Set-up
Install and use the TV set in accordance with the 
instructions below in order to avoid any risk of fire, 
electrical shock or damage and/or injuries.
Installation
 The TV set should be installed near an easily accessible 
mains socket.
 Place the TV set on a stable, level surface.
 Only qualified service personnel should carry out wall 
installations.
 For safety reasons, it is strongly recommended that you 
use Sony accessories, including:
– Wall-mount bracket SU-WL500
Transporting
 Before transporting the TV set, 
disconnect all cables.
 Two or three people are needed to 
transport a large TV set.
 When transporting the TV set by 
hand, hold it as shown on the right.
 When lifting or moving the TV set, 
hold it firmly from the bottom. Do 
not put stress on the LCD panel.
 When transporting the TV set, do 
not subject it to jolts or excessive 
vibration.
 When transporting the TV set for 
repairs or when moving, pack it using the original carton 
and packing material.
Ventilation
 Never cover the ventilation holes or insert anything in the 
cabinet.
 Leave space around the TV set as shown below.
 It is strongly recommended that you use a Sony wall-
mount bracket in order to provide adequate air-circulation.
Installed on the wallInstalled with stand
 To ensure proper ventilation and prevent the collection of 
dirt or dust:
– Do not lay the TV set flat, install upside down, 
backwards, or sideways.
– Do not place the TV set on a shelf, rug, bed or in a 
closet.
– Do not cover the TV set with a cloth, such as curtains, 
or items such as newspapers, etc.
– Do not install the TV set as shown below.
Mains lead
Handle the mains lead and socket as follows in order 
to avoid any risk of fire, electrical shock or damage 
and/or injuries:
– Connect the TV set using a three-wire grounding type 
mains plug to a mains socket with a protective earthing 
connection.
– Use only Sony mains leads, not those of other brands.
– Insert the plug fully into the mains socket.
– Operate the TV set on a 220-240 V AC supply only.
– When wiring cables, be sure to unplug the mains lead 
for your safety and care not to catch your feet on the 
cables.
– Disconnect the mains lead from the mains socket before 
working on or moving the TV set.
– Keep the mains lead away from heat sources.
– Unplug the mains plug and clean it regularly. If the plug 
is covered with dust and it picks up moisture, its 
insulation may deteriorate, which could result in a fire. 
Notes
 Do not use the supplied mains lead on any other 
equipment.
 Do not pinch, bend, or twist the mains lead excessively. 
The core conductors may be exposed or broken.
 Do not modify the mains lead.
 Do not put anything heavy on the mains lead.
 Do not pull on the mains lead itself when disconnecting 
the mains lead.
 Do not connect too many appliances to the same mains 
socket.
 Do not use a poor fitting mains socket.
30 cm
10 cm 10 cm
10 cm
Leave at least this space around the set.
30 cm
10 cm 10 cm 6 cm
Leave at least this space around the set.
Air circulation is blocked.
Wall Wall
Continued
 
						

							8 GB
Prohibited Usage
Do not install/use the TV set in locations, 
environments or situations such as those listed below, 
or the TV set may malfunction and cause a fire, 
electrical shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or 
other vessel, inside a vehicle, in medical institutions, near 
flammable objects (candles, etc).
Environment:
Places that are hot, humid, or excessively dusty; where 
insects may enter; where it might be exposed to mechanical 
vibration; unstable locations; near water, rain, moisture or 
smoke.
Situation:
Do not use when your hands are wet, with the cabinet 
removed, or with attachments not recommended by the 
manufacturer. Disconnect the TV set from mains socket and 
aerial during lightning storms.
Broken pieces:
 Do not throw anything at the TV set. The screen glass may 
break by the impact and cause serious injury.
 If the surface of the TV set cracks, do not touch it until you 
have unplugged the mains lead. Otherwise electric shock 
may result.
When not in use
 If you will not be using the TV set for several days, the TV 
set should be disconnected from the mains for 
environmental and safety reasons. 
 As the TV set is not disconnected from the mains when the 
TV set is just turned off, pull the plug from the mains to 
disconnect the TV set completely.
 However, some TV sets may have features that require the 
TV set to be left in standby to work correctly.
For children
 Do not allow children to climb on the TV set.
 Keep small accessories out of the reach of children, so that 
they are not mistakenly swallowed. 
If the following problems occur...
Turn off the TV set and unplug the mains lead 
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it 
checked by qualified service personnel.
When:
– Mains lead is damaged.
– Poor fitting of mains socket.
– TV set is damaged by being dropped, hit or having 
something thrown at it.
– Any liquid or solid object falls through openings in the 
cabinet.
Precautions
Viewing the TV
 View the TV in moderate light, as viewing the TV in poor 
light or during long period of time, strains your eyes.
 When using headphones, adjust the volume so as to avoid 
excessive levels, as hearing damage may result.
LCD Screen
 Although the LCD screen is made with high-precision 
technology and 99.99% or more of the pixels are effective, 
black dots may appear or bright points of light (red, blue, 
or green) may appear constantly on the LCD screen. This 
is a structural property of the LCD screen and is not a 
malfunction.
 Do not push or scratch the front filter, or place objects on 
top of this TV set. The image may be uneven or the LCD 
screen may be damaged.
 If this TV set is used in a cold place, a smear may occur in 
the picture or the picture may become dark. This does not 
indicate a failure. These phenomena disappear as the 
temperature rises.
 Ghosting may occur when still pictures are displayed 
continuously. It may disappear after a few moments.
 The screen and cabinet get warm when this TV set is in 
use. This is not a malfunction.
 The LCD screen contains a small amount of liquid crystal 
and mercury. The fluorescent tubes used in this TV set 
also contain mercury. Follow your local ordinances and 
regulations for disposal.
Handling and cleaning the screen surface/cabinet of 
the TV set
Be sure to unplug the mains lead connected to the TV set 
from mains socket before cleaning.
To avoid material degradation or screen coating degradation, 
observe the following precautions.
 To remove dust from the screen surface/cabinet, wipe 
gently with a soft cloth. If dust is persistent, wipe with a 
soft cloth slightly moistened with a diluted mild detergent 
solution.
 Never use any type of abrasive pad, alkaline/acid cleaner, 
scouring powder, or volatile solvent, such as alcohol, 
benzene, thinner or insecticide. Using such materials or 
maintaining prolonged contact with rubber or vinyl 
materials may result in damage to the screen surface and 
cabinet material.
 When adjusting the angle of the TV set, move it slowly so 
as to prevent the TV set from moving or slipping off from 
its table stand.
Optional Equipment
Keep optional components or any equipment emitting 
electromagnetic radiation away from the TV set. Otherwise 
picture distortion and/or noisy sound may occur.
 
						

							9 GB
Overview of the remote
z The number 5, PROG + and A/B 
buttons have tactile dots. Use the tactile 
dots as references when operating the 
TV.
 If you turn the TV off, Theatre Mode is 
also turned off.
1"/1 – TV standby
Turns the TV on and off from standby mode.
2A/B – Dual Sound (page 24)
3Coloured buttons (page 12, 13, 15)
4/  – Input select / Text hold
 In TV mode (page 18): Selects the input source from equipment connected 
to the TV sockets.
 In Analogue Text mode (page 12): Holds the current page.
5F/f/G/g/  (page 11, 20)
6TOOLS (page 12, 18)
Enables you to access various viewing options and change/make adjustments 
according to the source and screen format.
7MENU (page 20)
8THEATRE
You can set Theatre Mode on or off. When Theatre Mode is set to on, the 
optimum audio output (if the TV is connected with an audio system using an 
HDMI cable) and picture quality for film videos are automatically set.
9Number buttons
 In TV mode: Selects channels. For channel numbers 10 and above, enter 
the second and third digit quickly.
 In Analogue Text mode: Enters the three digit page number to select the 
page.
0 – Previous channel
Returns to the previous channel watched (for more than five seconds).
qaPROG +/-/ /
 In TV mode (page 11): Selects the next (+) or previous (-) channel.
 In Analogue Text mode (page 12): Selects the next ( ) or previous ( ) 
page.
qs% – Mute (page 11, 18)
qd2 +/- – Volume (page 18)
qf/ – Text (page 11)
qgDIGITAL – Digital mode (page 11)
qhANALOG – Analogue mode (page 11)
qjRETURN / 
Returns to the previous screen of any displayed menu.
qk – EPG (Digital Electronic Programme Guide) (page 13)
ql – Picture freeze (page 11)
Freezes the TV picture.
w; – Screen mode (page 12)
wa/  – Info / Text reveal
 In digital mode: Displays brief details of the programme currently being 
watched.
 In analogue mode: Displays information such as current channel number 
and screen format.
 In Analogue Text mode (page 12): Reveals hidden information (e.g. 
answers to a quiz).
 
						

							10 GB
Overview of the TV buttons and indicators
1 (page 20)
2/  – Input select / OK
 In TV mode (page 18): Selects the input source 
from equipment connected to the TV sockets.
 In TV menu: Selects the menu or option, and 
confirms the setting.
32 +/-/ /
 In TV mode: Increases (+) or decreases (-) the 
volume.
 In TV menu: Moves through the options right ( ) 
or left ( ).
4PROG +/-/ /
 In TV mode: Selects the next (+) or previous (-) 
channel.
 In TV menu: Moves through the options up ( ) or 
down ( ).
51 – Power
Turns the TV on or off.
~
To disconnect the TV completely, pull the plug from the 
mains.
6   – Picture Off / Timer indicator
Light sensor (page 29)
 Lights up in green when the picture is switched off 
(page 28).
 Lights up in orange when the timer is set 
(page 28).
71 – Standby indicator
Lights up in red when the TV is in standby mode.
8"   – Power / Timer REC programme indicator
 Lights up in green when the TV is turned on.
 Lights up in orange when the timer recording is set 
(page 13).
 Lights up in red during the timer recording.
9Remote control sensor
 Receives IR signals from the remote.
 Do not put anything over the sensor, as its function 
may be affected.
~
Make sure that the TV is completely turned off before 
unplugging the mains lead. Unplugging the mains lead while 
the TV is turned on may cause the indicator to remain lit or 
may cause the TV to malfunction.