Sony Kdl 40lx903 Operating Instructions

							4-187-903-11(1)
LCD 
Digital Colour TV
Operating Instructions
Setting Up
Watching TV
Additional Information
KDL-60LX903 / 40LX903
 
						

							2GB
NOTICE FOR 
CUSTOMERS IN 
THE UNITED 
KINGDOM
A moulded plug complying with BS1363 is 
fitted to this equipment for your safety and 
convenience.
Should the fuse in the plug supplied need to 
be replaced with the same rating of fuse 
approved by ASTA or BSI to BS 1362 (i.e., 
marked with   or  ) must be used.
When an alternative type of plug is used it 
should be fitted with the same rating of 
fuse, otherwise the circuit should be 
protected by a 10 AMP FUSE at the 
distribution board.
If the plug supplied with this equipment has 
a detachable fuse cover, be sure to attach 
the fuse cover after you change the fuse. 
Never use the plug without the fuse cover. 
If you should lose the fuse cover, please 
contact your nearest Sony service station.
How to replace the fuseOpen the fuse compartment with a blade 
screwdriver, and replace the fuse.
Please refer to the illustration that actually 
equipped with the product.
Introduction
Thank you for choosing this Sony product. 
Before operating the TV, please read this 
manual thoroughly and retain it for future 
reference.
Notes on Digital TV 
function
•Any functions related to Digital TV 
( ) will only work in countries or 
areas where DVB-T (MPEG-2 and 
H.264/MPEG-4 AVC) digital terrestrial 
signals are broadcast or where you have 
access to a compatible DVB-C (MPEG-
2 and H.264/MPEG-4 AVC) cable 
service. Please confirm with your local 
dealer if you can receive a DVB-T signal 
where you live or ask your cable 
provider if their DVB-C cable service is 
suitable for integrated operation with 
this TV.
Your cable provider may charge a fee for 
their services, or require you to agree to 
its terms and conditions of business.
This TV set complies with DVB-T and 
DVB-C specifications, but compatibility 
with future DVB-T digital terrestrial and 
DVB-C digital cable broadcasts are not 
guaranteed.
Some Digital TV functions may not be 
available in some countries/areas and 
DVB-C cable may not operate correctly 
with some providers.
For a list of compatible cable providers, 
refer to the support web site:
http://support.sony-europe.com/TV/
DVBC/
~
Instructions about “Installing Wall 
Mount Bracket” are included within this 
TV’s instructions manual.
The illustrations used in this manual may 
differ depending on your TV model.
Trademark information
 is a registered trademark of the DVB 
Project.
HDMI, the HDMI Logo, and High-
Definition Multimedia Interface are 
trademarks or registered trademarks of 
HDMI Licensing LLC in the United States 
and other countries.
DLNA®, the DLNA Logo and DLNA 
CERTIFIED® are trademarks, service 
marks, or certification marks of the Digital 
Living Network Alliance.
DivX® is a video file compression 
technology, developed by DivX, Inc.
DivX, DivX Certified, and associated 
logos are trademarks of DivX, Inc. and are 
used under license.
ABOUT DIVX VIDEO: DivX® is a 
digital video format created by DivX,Inc. 
This is an official DivX Certified device 
that plays DivX video. Visit 
www.divx.com for more information and 
software tools to convert your files into 
DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: 
This DivX Certified® device must be 
registered in order to play DivX Video-on-
Demand (VOD) content. To generate the 
registration code, locate the DivX VOD 
section in the device setup menu. Go to 
vod.divx.com with this code to complete 
the registration process and learn more 
about DivX VOD.
Manufactured under license from Dolby 
Laboratories. Dolby and the double-D 
symbol are trademarks of Dolby 
Laboratories.
“BRAVIA” and   are 
trademarks of Sony Corporation.
“XMB
™” and “XrossMediaBar” are 
trademarks of Sony Corporation and Sony 
Computer Entertainment Inc.
“FACE DETECTION” logo is trademark 
of Sony Corporation.
Notice for Wireless 
Signal
1. Hereby, Sony, declares that this unit is 
in compliance with the essential 
requirements and other relevant provisions 
of Directive 1999/5/EC.
To obtain the declaration of conformity 
(DoC) for R&TTE Directive, please access 
the following URL address.
http://www.compliance.sony.de/
2. TV wireless system may be operated in 
following EU countries:
Austria, Belgium, Bulgaria, Cyprus, Czech 
Republic, Denmark, Estonia, Finland, 
France, Germany, Greece, Hungary, 
Iceland, Ireland, Italy, Latvia, 
Liechtenstein, Lithuania, Luxembourg, 
Malta, The Netherlands, Norway, Poland, 
Portugal, Slovak Republic, Romania, 
Slovenia, Spain, Sweden, Switzerland, 
Turkey, and The United Kingdom.
This equipment can be operated in other 
non-European countries.
Location of the 
identification label
Labels for Model No. and Power Supply 
rating (in accordance with applicable 
safety regulation) are located on the rear of 
the TV. They can be found by removing 
the bottom cover.
The manufacturer of this product is 
Sony Corporation, 1-7-1 Konan 
Minato-ku Tokyo, 108-0075 Japan. 
The Authorized Representative for 
EMC and product safety is Sony 
Deutschland GmbH, Hedelfinger 
Strasse 61, 70327 Stuttgart, 
Germany. For any service or 
guarantee matters please refer to the 
addresses given in separate service 
or guarantee documents.
FUSE
FUSE
 
						

							3GB
Table of Contents
Checking the accessories .............................................................................................................. 3
Inserting batteries into the remote ................................................................................................. 3
Setting Up
Attaching the Table-Top Stand (except KDL-60LX903)................................................................. 4
Connecting an antenna (aerial)/Set Top Box/recorder (e.g. DVD recorder) .................................. 5
Preventing the TV from toppling over ............................................................................................6
Bundling the cables........................................................................................................................ 6
Performing the initial set-up ........................................................................................................... 7
Detaching the Table-Top Stand from the TV ................................................................................. 7
Watching TV
To watch programmes ................................................................................................................... 8
To utilise the TV’s features ............................................................................................................ 8
To use i-Manual ............................................................................................................................. 9
To use 3D Glasses ...................................................................................................................... 10
Additional Information
Troubleshooting ........................................................................................................................... 12
Specifications ............................................................................................................................... 13
Installing the Accessories (Wall-Mount Bracket).......................................................................... 15
Safety Information ........................................................................................................................ 20
Precautions .................................................................................................................................. 21
Checking the accessories
AC power cord (mains lead) (1)
Cable holder (1) (except KDL-60LX903)
Remote (1)
Size AAA batteries (R3 type) (2)
Table-Top Stand (1)*1 (except KDL-60LX903)
Fixing screws for Table-Top Stand 
(M5 × 16) (4) (except KDL-60LX903)
Assembling screws for Table-Top Stand 
(M5 × 16) (4) (KDL-40LX903 only)
Black spacers (4) (KDL-40LX903 only)
Silver spacers (4) (KDL-60LX903 only)
Screws (M6 × 20) (4) (KDL-60LX903 only)
Stand rear cover (1)*
2
Bottom cover (1)*3
3D Glasses (battery included) (2)
Pouch for 3D Glasses (2)
*1For KDL-40LX903, assemble the Table-Top 
Stand with the supplied assembling screws.
Refer to the supplied Table-Top Stand leaflet to 
assemble the stand.*
2For KDL-60LX903, the stand rear cover is 
factory-attached to the Table-Top Stand.
*
3For KDL-60LX903, the bottom cover is factory-
attached to the TV.
Inserting batteries into the 
remote
1Remove the protection sheet.
2Push and slide the cover upward.
Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for operation (page 9).
Before operating the TV, please read “Safety Information” (page 20). Retain this manual for future reference.
 
						

							4GB
Setting Up
Attaching the Table-Top 
Stand (except KDL-
60LX903)
1Refer to the supplied Table-Top Stand 
leaflet for proper attachment for some 
TV models.
2Place the TV set on the Table-Top 
Stand.
3Fix the TV to the Table-Top Stand 
according to the arrow marks   that 
guide the screw holes using the 
supplied screws.
~
If using an electric screwdriver, set the tightening 
torque at approximately 1.5 N·m {15 kgf·cm}.
4After all the screws have been 
tightened, attach the supplied stand rear 
cover to the Table-Top Stand.
Adjusting the viewing angle of 
the TV (except KDL-60LX903)
This TV can be adjusted within the angles 
shown below.
~
To return to 0°, reverse the above procedure.
14
23
Remove screw as 
shown.6º 0º
Install screw into 
the top screw hole 
of the Table-Top 
Stand.
Slide in. Lift up and tilt.
 
						

							5GB
Setting Up
Ensure that there are no objects in front of the TV.
Do not expose the Intelligent Presence Sensor to 
direct sunlight or other strong light, as 
malfunction may occur.
Connecting an antenna 
(aerial)/Set Top Box/
recorder (e.g. DVD recorder)
Connecting a Set Top Box/recorder 
(e.g. DVD recorder) with SCART
~
Right Angle Type Universal SCART Lead is 
recommended for this connection.
Connecting a Set Top Box/recorder 
(e.g. DVD recorder) with HDMI
Intelligent Presence Sensor3D Sync Transmitter IR Sensor
Set Top Box/recorder (e.g. DVD recorder)
Set Top Box/recorder (e.g. DVD recorder)
(Continued)
 
						

							6GB
~
For KDL-40LX903, after connecting cables, 
install the bottom cover and stand rear cover.
Detaching the terminal cover
~
After connecting cables, re-attach the terminal 
cover to the TV.
Preventing the TV from 
toppling over
1Install a wood screw (4 mm in 
diameter, not supplied) in the TV stand.
2Install a machine screw (M4 × 16, not 
supplied) into the screw hole of the TV.
3Tie the wood screw and the machine 
screw with a strong cord (not supplied).
Bundling the cables
~
A cable holder is available for KDL-40LX903. To 
bundle the cables, follow steps 3 to 5.
~
Do not bundle the AC power cord (mains lead) 
together with other cables.
 
						

							7GB
Setting Up
Performing the initial set-up
1Connect the TV to your AC power 
outlet (mains socket).
2Check the ENERGY SAVING 
SWITCH setting is on (
z).
3Press 1 on the TV.
When you switch on the TV for the first 
time, the Language menu appears on the 
screen.
Follow the instructions on the screen.
Digital Auto Tuning: When you select 
“Cable”, we recommend that you select 
“Quick Scan” for quick tuning. Set 
“Frequency” and “Network ID” according 
to the information supplied from your cable 
provider. If no channel is found using 
“Quick Scan”, try “Full Scan” (though it 
may take some time).
For a list of compatible cable providers, 
refer to the support web site:
http://support.sony-europe.com/TV/
DVBC/Programme Sorting: Changes the order of 
analogue channels stored in the TV.
1Press F/f to select the channel you want 
to move to a new position, then press  .
2Press F/f to select the new position for 
the channel, then press  .
~
You can also tune channels manually.
Detaching the Table-Top 
Stand from the TV
~
Remove the stand rear cover and bottom cover 
prior to detaching the Table-Top Stand.
Remove the screws guided by the arrow marks   
of the TV.
Do not remove the Table-Top Stand for any 
reason other than to install corresponding 
accessories on the TV.
Be sure the TV is on the vertical position before 
switching on. TV set must not powered on with 
LCD panel face down to avoid uneven picture 
uniformity.
4
 
						

							8GB
Watching TV
To watch programmes
To utilise the TV’s features
HOME button
Press to display various operation and setting 
screens.OPTIONS button
Press to display convenient functions based on 
the current input or content.
z
The number 5, N, PROG + and AUDIO 
buttons on the remote have a tactile dot. 
Use the tactile dots as a reference when 
operating the TV.
1Turn on the TV.
1Switch ENERGY SAVING SWITCH 
on (
z).
2Press 1 on the TV to turn on the TV.
2Select a mode.
3Select a TV channel.
Using Digital Electronic Programme 
Guide
Press GUIDE in digital mode to display the 
programme guide.
GUIDE
OPTIONS
HOME
2
3
Settings
TVSystem Settings
Picture
Sound 
3D Menu
Add to Favourites
PA P
Motionflow
Presence Sensor
Scene Select
Sleep Timer
Headphone Volume
Speakers
 
						

							9GB
Watching TV
To use i-Manual
xWelcome to i-Manual
x“BRAVIA” TV Features
xWatching TV
Introduces convenient features such as EPG 
Guide, Favourites, etc.
xUsing the Home Menu
Customise your TV settings, etc.xFun Features with Connected 
Equipment
Introduces how to connect optional equipment.
xParts Description
xTroubleshooting
Find solutions for your problem.
xIndex
~
Images and illustrations may differ from what is displayed on the screen.
Operating instructions are built into your BRAVIA 
TV and can be displayed on the screen.
To learn more about your TVs features you can 
access your i-Manual with the touch of a button.
1Press i-MANUAL.
2Press G/g/F/f/ to select items.
1
2
(Continued)
 
						

							10GB
To use 3D Glasses
Before use: Remove the battery’s insulating sheet before using the product for the first time.
Parts and components
1Slide switch
Set the switch for a comfortable fit. Set 
both the switches on either side for a 
comfortable fit. Close the temple frames 
slightly inwards to set the switch.
2Battery cover
Detach the cover when replacing the 
battery.
3LED indicator
Flashes one time every 3 seconds: Power 
on
Flashes three times every 3 seconds: Low 
battery. Battery capacity is almost running 
out.
Flashes three times: Power off4IR sensor
Receive signals from the 3D Sync 
Transmitter.
IR’s entry angle differs according to 
distance or usage environment.
~
Please keep this face clean.
5Power button
Power on: Press once
Power off: Hold power button down for 2 
seconds
* Auto power off: More than 5 minutes without 
IR signal
6Nose pad
Adjust the nose pad for a comfortable fit.
7Temple frames
You can bend (adjust) the temple frames 
for a comfortable fit.
Pouch (2)
3D Glasses (2)
Increases the width 
of the glasses
Decreases the width 
of the glasses
This part receives IR 
(infrared rays) from the 
3D Sync Transmitter.