Sony Kdl 40bx420 Operating Instructions

							
4-270-481-12(1)
LCD 
Digital Colour TV
Operating Instructions
KDL-40NX520 / 40BX420 / 37BX420 / 32NX520 / 32BX420 / 32BX321 / 32BX320 / 26BX321
KDL-26BX320
 
						

							2 GB
NOTICE FOR 
CUSTOMERS IN 
THE UNITED 
KINGDOM
A moulded plug complying with BS1363 
is fitted to this equipment for your safety 
and convenience.
Should the fuse in the plug supplied need 
to be replaced with the same rating of fuse 
approved by ASTA or BSI to BS 1362 (i.e., 
marked with   or  ) must be used.
When an alternative type of plug is used it 
should be fitted with the same rating of 
fuse, otherwise the circuit should be 
protected by a 10 AMP FUSE at the 
distribution board.
If the plug supplied with this equipment 
has a detachable fuse cover, be sure to 
attach the fuse cover after you change the 
fuse. Never use the plug without the fuse 
cover. If you should lose the fuse cover, 
please contact your nearest Sony service 
station.
How to replace the fuseOpen the fuse compartment with a blade 
screwdriver, and replace the fuse.
Please refer to the illustration that actually 
equipped with the product.
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this 
manual thoroughly and retain it for future 
reference.
Notice for Digital TV 
function
• Any functions related to Digital TV 
( ) will only work in countries or 
areas where DVB-T (MPEG-2 and 
H.264/MPEG-4 AVC) digital terrestrial 
signals are broadcast or where you have 
access to a compatible DVB-C (MPEG-
2 and H.264/MPEG-4 AVC) cable 
service. Please confirm with your local 
dealer if you can receive a DVB-T signal 
where you live or ask your cable 
provider if their DVB-C cable service is 
suitable for integrated operation with this 
TV. Your cable provider may charge a fee for 
their services, or require you to agree to 
its terms and conditions of business.
 This TV set complies with DVB-T and 
DVB-C specifications, but compatibility 
with future DVB-T digital terrestrial and 
DVB-C digital cable broadcasts are not 
guaranteed.
 Some Digital TV functions may not be 
available in some countries/areas and 
DVB-C cable may not operate correctly 
with some providers.
~ 
 The illustration used in this 
manual are of the KDL-32BX320 
unless otherwise state.
Trademark information  is a registered trademark of the 
DVB Project.
 HDMI, the HDMI Logo, and High-
Definition Multimedia Interface are 
trademarks or registered trademarks of 
HDMI Licensing LLC in the United 
States and other countries.
 Manufactured under license from Dolby 
Laboratories. Dolby and the double-D 
symbol are trademarks of Dolby 
Laboratories.
 DivX®, DivX Certified® and associated 
logos are registered trademarks of DivX, 
Inc. and are used under license.
ABOUT DIVX VIDEO: DivX® is a 
digital video format created by DivX, 
Inc. This is an official DivX Certified 
device that plays DivX video. Visit 
www.divx.com for more information 
and software tools to convert your files 
into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: 
This DivX Certified® device must be 
registered in order to play DivX Video-
on-Demand (VOD) content. To generate 
the registration code, locate the DivX 
VOD section in the device setup menu. 
Go to vod.divx.com with this code to 
complete the registration process and 
learn more about DivX VOD.
 “BRAVIA” and   are 
trademarks of Sony Corporation.
Location of the 
identification label
Labels for Model No., Production Date 
(month/year) and Power Supply rating (in 
accordance with applicable safety 
regulation) are located on the rear of the 
TV or package.
FUSE
FUSE
The manufacturer of this product is 
Sony Corporation, 1-7-1 Konan 
Minato-ku Tokyo, 108-0075 Japan. 
The Authorized Representative for 
EMC and product safety is Sony 
Deutschland GmbH, Hedelfinger 
Strasse 61, 70327 Stuttgart, 
Germany. For any service or 
guarantee matters please refer to the 
addresses given in separate service or 
guarantee documents.
 
						

							3 GB
Start-up Guide 4
Safety Information.............................................................................................................9
Precautions......................................................................................................................10
Overview of the remote ..................................................................................................12
Overview of the TV buttons and indicators ..................................................................14
Watching TV
Watching TV ....................................................................................................................15
Using the Digital Electronic Programme Guide (EPG)  .......................................17
Using the Digital Favourite list  .............................................................................18
Using Optional Equipment
Connecting optional equipment ....................................................................................19
Viewing pictures from connected equipment ..............................................................20
Playing Back Photo/Music/Video via USB ....................................................................21
Using BRAVIA Sync with Control for HDMI ..................................................................24
Using MENU Functions
Navigating through TV Menu .........................................................................................25
Settings ............................................................................................................................26
Additional Information
Installing the Accessories (Wall-Mount Bracket) .........................................................36
Specifications ..................................................................................................................39
Troubleshooting ..............................................................................................................42
 : for digital channels only
• Before operating the TV, please read “Safety Information” (page 9). Retain this manual for future reference.
are included within this TV’s instructions manual.
Table of Contents
 
						

							4 GB
Start-up Guide
1: Checking the 
accessories
Table-Top Stand (1)
Screws for stand (4 + 3) (for KDL-40/32NX520 (8))
Remote RM-ED046 (1)
Size AA batteries (2)
To insert batteries into the remote
~ 
 Observe the correct polarity when inserting batteries.
 Do not use different types of batteries together or mix 
old and new batteries.
 Dispose of batteries in an environmentally friendly way. 
Certain regions may regulate the disposal of batteries. 
Please consult your local authority.
 Handle the remote with care. Do not drop or step on it, 
or spill liquid of any kind onto it.
 Do not place the remote in a location near a heat source, 
a place subject to direct sunlight, or a damp room.
2: Attaching the stand
~ 
 For best picture quality, do not expose the screen to 
direct illumination or sunlight.
 If the TV is brought directly from a cold to a warm 
location, or is placed in a very damp room, or is placed 
in a room in which heating has just been turned on, 
moisture may condense on the surface or inside the TV. 
Should this occur, turn off the TV and leave the TV off 
until the moisture evaporates, and then the TV can be 
used. If you notice moisture condensation between the 
glass panel and the LCD, turn on the TV and the 
condensation will evaporate after the TV has warmed 
up.
Follow the assembling steps required to place on a 
TV stand.
1Refer to the supplied Table-Top Stand 
leaflet for proper attachment for some TV 
models.
2Place the TV set on the stand. Take care 
not to interfere with cables.
3Fix the TV to the stand according to the 
arrow marks   that guide the screw 
holes using the supplied screws.
~ If using an electric screwdriver, set the tightening torque 
at approximately 1.5 N·m (15 kgf·cm).
Push to 
open
 
						

							5 GB
Start-up Guide3: Connecting an 
aerial/cable/VCR/DVD 
recorder
4: Preventing the TV 
from toppling over
1Install a wood screw (4 mm in diameter, 
not supplied) in the TV stand.
Coaxial cable
Connecting an aerial/cable only
Connecting an aerial/cable/VCR/DVD recorder with 
SCART
Scart lead
VCR/DVD recorderCoaxial cableCoaxial cableTerrestrial signal
or cable
Terrestrial 
signal or 
cable
Connecting an aerial/cable/ VCR/DVD recorder with 
HDMI
HDMI
cable
Coaxial cableCoaxial
cable
VCR/DVD recorderTerrestrial signal 
or cable
2
1
3
Continued
 
						

							6 GB
2Install a machine screw (M4 × 16, not 
supplied) into the screw hole of the TV.
3Tie the wood screw and the machine 
screw with a strong cord (not supplied).
z 
 An optional Sony support belt kit is used to secure the TV. 
Contact your nearest Sony Service Centre to purchase a 
kit. Have your TV model name ready for reference.
5: Selecting the 
language, country/region 
and location
1Connect the TV to your mains socket 
(220-240V AC, 50Hz).
2Press 1 on the side of the TV.
When you turn on the TV for the first time, the 
Language menu appears on the screen.
~ 
 When you turn on the TV, the power indicator lights 
up in green.
3Press F/f/G/g to select the language 
displayed on the menu screens, then
press
 .
4Follow the on-screen instructions to 
select the country/region in which you will 
operate the TV.
If the country/region which you want to use on 
the TV does not appear in the list, select “-” 
instead of a country/region.
5Follow the on-screen instructions to set 
the PIN code.
z 
 Any PIN code can be used, except 0000. To change 
the PIN code later, see page 33.
6Follow the on-screen instructions to 
select the location type in which you will 
operate the TV.
This option selects the initial picture mode 
appropriate for the typical lighting condition in 
these environments.
In Shop mode, some settings will be periodically 
reset for Shop usage.
3,4,5,6
Language
Select Next
Select language.
 
						

							7 GB
Start-up Guide6: Auto-tuning the TV
1Press G/g to select “Start”, then press  .
2Press F/f to select “Antenna” or “Cable”, 
then press  .
If you select “Cable”, the screen for selecting the 
scan type appears. See “To tune the TV for 
Cable connection” (page 7).
The TV then starts searching for all available 
digital channels, followed by all available 
analogue channels. This may take some time, so 
do not press any buttons on the TV or remote 
while proceeding.
If a message appears for you to confirm the 
aerial connection
No digital or analogue channels were found. 
Check all the aerial/cable connections and press 
 to start auto-tuning again. 
3Programme Sorting (Only in analogue 
mode): Changes the order in which the 
analogue channels are stored on the TV.
1Press F/f to select the channel you want to 
move to a new position, then press 
g.
2Press 
F/f to select the new position for your 
channel, then press  .
If you do not change the order in which the 
analogue channels are stored on the TV, press 
HOME to go to next step.
~ This step will not appear if any analogue channel is 
found.
The message “Set-up complete” will appear on 
the screen. Press  .
The TV has now tuned in all the available 
channels.
z 
 USB System Update 
You can update the TV system using USB memory.
Obtain information from the website below.
http://support.sony-europe.com/TV/
To tune the TV for Cable connection
1Press  and F/f to select “Quick Scan” 
or “Full Scan”, then press  .
“Quick Scan” : channels are tuned according to 
the cable operator information within the 
broadcast signal. 
Recommended setting for “Frequency” and 
“Network ID” is “Auto”.
This option is recommended for fast tuning 
when supported by your cable operator. 
If the “Quick Scan” does not tune, please use the 
“Full Scan” method below.
“Full Scan” : All available channels are tuned 
and stored. This procedure may take some time.
This option is recommended when “Quick Scan” 
is not supported by your cable provider.
2Press f to select “Start”.
The TV starts searching for channels. Do not 
press any buttons on the TV or remote.
~ Some cable providers do not support “Quick Scan”. If no 
channels are detected using “Quick Scan”, perform “Full 
Scan”.
StartSkip
Do you want to start Auto Tuning? Auto Tuning
 
						

							8 GB
Adjusting the viewing 
angle of the TV (NX520 
models only)
This TV can be adjusted within the angles 
shown below.
 To return to 0°, reverse the above procedure.
Detaching the Table-
Top Stand from the TV
~ 
 Do not remove the Table-Top Stand for any reason other 
than to wall-mount the TV.
z
 
 Be sure the TV is on the vertical position before 
switching on. TV set must not be powered on with LCD 
panel face down to avoid uneven picture uniformity.
14
23
Remove screw as 
shown.Install screw into 
the top screw hole 
of the Table-Top 
Stand.
Slide in. Lift up and tilt.6º 0º
Table-Top 
Stand
 
						

							9 GB
Safety 
Information
Installation/Set-upInstall and use the TV set in accordance 
with the instructions below in order to 
avoid any risk of fire, electrical shock or 
damage and/or injuries.
Installation The TV set should be installed near an 
easily accessible mains socket.
 Place the TV set on a stable, level 
surface.
 Only qualified service personnel should 
carry out wall installations.
 For safety reasons, it is strongly 
recommended that you use Sony 
accessories, including:
– Wall-mount bracket 
SU-WL500
(except KDL-26BX321/KDL-
26BX320)
SU-WL100
(KDL-26BX321/KDL-26BX320)
 Be sure to use the screws supplied with 
the Wall-mount bracket when attaching 
the mounting hooks to the TV set. The 
supplied screws are designed as 
indicated by illustration when measured 
from the attaching surface of the 
mounting hook. The diameter and length 
of the screws differ depending on the 
Wall-mount bracket model. Use of 
screws other than those supplied may 
result in internal damage to the TV set or 
cause it to fall, etc.
Transporting Before transporting the TV set, 
disconnect all cables.
 Two or three people are needed to 
transport a large TV set.
 When transporting the TV set by hand, 
hold it as shown in the illustration. Do 
not put stress on the LCD panel and the 
frame around the screen.
 When lifting or moving the TV set, hold 
it firmly from the bottom. When transporting the TV set, do not 
subject it to jolts or excessive vibration.
 When transporting the TV set for repairs 
or when moving, pack it using the 
original carton and packing material.
Ventilation Never cover the ventilation holes or 
insert anything in the cabinet.
 Leave space around the TV set as shown 
below.
 It is strongly recommended that you use 
a Sony wall-mount bracket in order to 
provide adequate air-circulation.
Installed on the wall
Installed with stand
 To ensure proper ventilation and prevent 
the collection of dirt or dust:
– Do not lay the TV set flat, install 
upside down, backwards, or 
sideways.
– Do not place the TV set on a shelf, 
rug, bed or in a closet.
– Do not cover the TV set with a cloth, 
such as curtains, or items such as 
newspapers, etc.
– Do not install the TV set as shown 
below.
Mains leadHandle the mains lead and socket as 
follows in order to avoid any risk of fire, 
electrical shock or damage and/or injuries:
– Use only mains leads supplied by 
Sony, not other suppliers.
– Insert the plug fully into the mains 
socket.
– Operate the TV set on a 220–240 V AC 
supply only.
– When wiring cables, be sure to unplug 
the mains lead for your safety and take care not to catch your feet on the 
cables.
– Disconnect the mains lead from the 
mains socket before working on or 
moving the TV set.
– Keep the mains lead away from heat 
sources.
– Unplug the mains plug and clean it 
regularly. If the plug is covered with 
dust and it picks up moisture, its 
insulation may deteriorate, which 
could result in a fire. 
Notes Do not use the supplied mains lead on 
any other equipment.
 Do not pinch, bend, or twist the mains 
lead excessively. The core conductors 
may be exposed or broken.
 Do not modify the mains lead.
 Do not put anything heavy on the mains 
lead.
 Do not pull on the mains lead itself when 
disconnecting the mains lead.
 Do not connect too many appliances to 
the same mains socket.
 Do not use a poor fitting mains socket.
Prohibited UsageDo not install/use the TV set in locations, 
environments or situations such as those 
listed below, or the TV set may 
malfunction and cause a fire, electrical 
shock, damage and/or injuries.
Location: Outdoors (in direct sunlight), at the 
seashore, on a ship or other vessel, inside 
a vehicle, in medical institutions, 
unstable locations, near water, rain, 
moisture or smoke.
 If the TV is placed in the changing room 
of a public bath or hot spring, the TV 
may be damaged by airborne sulfur, etc.
Environment: Places that are hot, humid, or excessively 
dusty; where insects may enter; where it 
might be exposed to mechanical 
vibration, near flammable objects 
(candles, etc). The TV set shall not be 
exposed to dripping or splashing and no 
objects filled with liquids, such as vases, 
shall be placed on the TV.
 Do not place the TV in a humid or dusty 
space, or in a room with oily smoke or 
steam (near cooking tables or 
humidifiers). Fire, electric shock, or 
warping may result.
Situation: Do not use when your hands are wet, 
with the cabinet removed, or with 
attachments not recommended by the 
manufacturer. Disconnect the TV set 
from mains socket and aerial during 
lightning storms.
 Do not install the TV so that it sticks out 
into an open space. Injury or damage 
from a person or object bumping into the 
TV may result.
Broken pieces:
 Do not throw anything at the TV set. The 
screen glass may break by the impact and 
cause serious injury.
 If the surface of the TV set cracks, do not 
touch it until you have unplugged the 
mains lead. Otherwise electric shock 
may result.
Mounting Hook
Hook attachment on rear 
of TV set Screw (supplied with the 
Wall-mount bracket) Min. ~ 26 TV: 6.5 ~ 10mm 
32 TV ~ Max.: 8 ~ 12mm
KDL-26BX321/
KDL-26BX320Except 
KDL-26BX321/
KDL-26BX320
30 cm
10 cm 10 cm
10 cm
Leave at least this space around 
the set.
30 cm
10 cm
10 cm6 cm
Leave at least this space around 
the set.
Air circulation is blocked.
Wall Wall
Continued
 
						

							10 GB
 Do not subject the LCD screen to any 
strong impact or shock. The screen glass 
may crack or shatter and cause injury.
When not in use
 If you will not be using the TV set for 
several days, the TV set should be 
disconnected from the mains for 
environmental and safety reasons. 
 As the TV set is not disconnected from 
the mains when the TV set is just turned 
off, pull the plug from the mains to 
disconnect the TV set completely.
 However, some TV sets may have 
features that require the TV set to be left 
in standby to work correctly.
For children
 Do not allow children to climb on the TV 
set.
 Keep small accessories out of the reach 
of children, so that they are not 
mistakenly swallowed. 
If the following problems 
occur...
Turn off the TV set and unplug the mains 
lead immediately if any of the following 
problems occur.
Ask your dealer or Sony service centre to 
have it checked by qualified service 
personnel.
When:– Mains lead is damaged.
– Poor fitting of mains socket.
– TV set is damaged by being dropped, 
hit or having something thrown at it.
– Any liquid or solid object falls through 
openings in the cabinet.
WarningTo prevent the spread of fire, keep candles 
or other open flames away from this 
product at all time.
Precautions
Viewing the TV View the TV in moderate light, as 
viewing the TV in poor light or during 
long period of time, strains your eyes.
 When using headphones, adjust the 
volume so as to avoid excessive levels, 
as hearing damage may result.
LCD Screen Although the LCD screen is made with 
high-precision technology and 99.99% or more of the pixels are effective, black 
dots may appear or bright points of light 
(red, blue, or green) may appear 
constantly on the LCD screen. This is a 
structural property of the LCD screen 
and is not a malfunction.
 Do not push or scratch the front filter, or 
place objects on top of this TV set. The 
image may be uneven or the LCD screen 
may be damaged.
 If this TV set is used in a cold place, a 
smear may occur in the picture or the 
picture may become dark. This does not 
indicate a failure. These phenomena 
disappear as the temperature rises.
 Ghosting may occur when still pictures 
are displayed continuously. It may 
disappear after a few moments.
 The screen and cabinet get warm when 
this TV set is in use. This is not a 
malfunction.
 The LCD screen contains a small amount 
of liquid crystal. Some fluorescent tubes 
used in this TV set also contain mercury. 
Follow your local ordinances and 
regulations for disposal.
Handling and cleaning the 
screen surface/cabinet of 
the TV set
Be sure to unplug the mains lead connected 
to the TV set from mains socket before 
cleaning.
To avoid material degradation or screen 
coating degradation, observe the following 
precautions.
 To remove dust from the screen surface/
cabinet, wipe gently with a soft cloth. If 
dust is persistent, wipe with a soft cloth 
slightly moistened with a diluted mild 
detergent solution.
 Do not spray water or detergent directly  
on the TV set. It may drip to the bottom 
of the screen or exterior parts, and may 
cause a malfunction.
 Never use any type of abrasive pad, 
alkaline/acid cleaner, scouring powder, 
or volatile solvent, such as alcohol, 
benzene, thinner or insecticide. Using 
such materials or maintaining prolonged 
contact with rubber or vinyl materials 
may result in damage to the screen 
surface and cabinet material.
 Periodic vacuuming of the ventilation 
openings is recommended to ensure to 
proper ventilation.
 When adjusting the angle of the TV set, 
move it slowly so as to prevent the TV 
set from moving or slipping off from its 
table stand.
Optional Equipment Keep optional components or any 
equipment emitting electromagnetic 
radiation away from the TV set. 
Otherwise picture distortion and/or noisy 
sound may occur.
 This equipment has been tested and 
found to comply with the limits set out in 
the EMC Directive using a connection 
signal cable shorter than 3 meters.
Batteries Observe the correct polarity when 
inserting batteries.
 Do not use different types of batteries 
together or mix old and new batteries.
 Dispose of batteries in an 
environmentally friendly way. Certain 
regions may regulate the disposal of batteries. Please consult your local 
authority.
 Handle the remote with care. Do not 
drop or step on it, or spill liquid of any 
kind onto it.
 Do not place the remote in a location 
near a heat source, a place subject to 
direct sunlight, or a damp room.
Disposal of the TV set
Disposal of Old 
Electrical & 
Electronic 
Equipment 
(Applicable in 
the European 
Union and other European 
countries with separate 
collection systems)
This symbol on the product or on its 
packaging indicates that this product shall 
not be treated as household waste. Instead 
it shall be handed over to the applicable 
collection point for the recycling of 
electrical and electronic equipment. By 
ensuring this product is disposed of 
correctly, you will help prevent potential 
negative consequences for the 
environment and human health, which 
could otherwise be caused by 
inappropriate waste handling of this 
product. The recycling of materials will 
help to conserve natural resources. For 
more detailed information about recycling 
of this product, please contact your local 
Civic Office, your household waste 
disposal service or the shop where you 
purchased the product.
Disposal of 
waste batteries 
(applicable in the 
European Union 
and other 
European 
countries with separate 
collection systems)
This symbol on the battery or on the 
packaging indicates that the battery 
provided with this product shall not be 
treated as household waste. On certain 
batteries this symbol might be used in 
combination with a chemical symbol. The 
chemical symbols for mercury (Hg) or lead 
(Pb) are added if the battery contains more 
than 0.0005% mercury or 0.004% lead. By 
ensuring these batteries are disposed of 
correctly, you will help prevent potentially 
negative consequences for the 
environment and human health which 
could otherwise be caused by 
inappropriate waste handling of the 
battery. The recycling of the materials will 
help to conserve natural resources. In case 
of products that for safety, performance or 
data integrity reasons require a permanent 
connection with an incorporated battery, 
this battery should be replaced by qualified