Sony Kdl 32l4000 Operating Instructions

Getting Started
11
Getting Started3Gently slide the TV unit onto the neck of the Table-Top Stand and align 
the screws holes.
4Use the supplied screws to attach the TV unit to the Table-Top Stand.
Do not put stress on the LCD panel and the frame around the screen.
Be careful not to pinch your hands or the AC power cord when you 
install the TV to the Table-Top Stand.
If an electric screwdriver is used, set the torque to tighten at 
approximately 1.5 N·m {15 kgf·cm}.
Rear of TV
Screw
 

Getting Started
12
Connecting the TV
To display clear crisp pictures, you must connect your TV correctly and select 
the correct 
Wide Mode to display the picture in the correct aspect ratio (see 
“Changing the Wide Screen Mode” on page 22). It is strongly recommended to 
connect the antenna/cable input using the 75-ohm coaxial cable (not supplied) 
to receive optimum picture quality signal. A 300-ohm twin lead cable can be 
easily affected by radio noise and the like, resulting in signal deterioration....

Getting Started
13
Getting Started
Cable System and 
VHF/UHF Antenna 
SystemIf you want to watch both antenna (over-the-air) and cable broadcast signals, 
you’ll need to use an optional A-B RF switch (not supplied), as shown 
below. 
Use the A-B selector to switch between the 
over-the-air signals and the cable signals. Then 
set the 
Cable setting in the Channel settings to On 
or 
Off, as described on page 29.
Satellite Receiver 
and Cable/Antenna
B A
Cable
AntennaA/B
RF SwitchRear of TV 
CABLE/ANTENNA...

Getting Started
14
VCR, Cable and 
Antenna
AUDIOL
RAUDIO
CABLE/ANTENNA
L
RAUDIOL P
R
PB
Y
R
AUDIO VIDEOS VIDEO RGB(MONO)AUDIOL
R
(1080i/720p/480p/480i) (FIX)
IN PC INVIDEO INCOMPONENT INDIGITAL
AUDIO OUT
(OPTICAL)
AUDIO OUT12112
A/V cable
CATV cableAntenna cable 
(not supplied) SVIDEO
AUDIO-L (white)
AUDIO-R (red) S VIDEO cable
VCRVIDEO 
(yellow)Rear of TV
VIDEO IN 2 is also available for a VIDEO cable connection.
If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) 
instead of the S...

Getting Started
15
Getting StartedWhen Connecting to Optional Equipment
SERVICE
ONLY
AUDIO
VIDEO INR
2L VIDEO
(MONO)
1AUDIOL
RAUDIO
CABLE/ANTENNA
L
RAUDIOL P
R
PB
Y
R
AUDIO VIDEOS VIDEO RGB(MONO)AUDIOL
R
(1080i/720p/480p/480i) (FIX)
IN PC IN VIDEO IN COMPONENT INDIGITAL
AUDIO OUT
(OPTICAL)
AUDIO OUT12 1 12
234 5 6 7
8qa0
9
Left side Rear
For 
service 
use only
ItemDescription
1VIDEO IN 2 
VIDEO/
L(MONO)-AUDIO-
RConnect to the composite video and audio output jacks on your camcorder or other video...

Getting Started
16
4PC IN 
(RGB/AUDIO) Connect to a personal computer’s video output connector using HD15-HD15 cable (analog 
RGB, not supplied). Can also be connected to other analog RGB devices.
See “PC Input Signal Reference Chart” on page 38 for the signals that can be displayed.
For some Apple Macintosh computers, it may be necessary to use an adapter 
(not supplied). If this is the case, connect the adapter to the computer before 
connecting the HD15-HD15 cable.
 If the picture is noisy, flickering...

Getting Started
17
Getting StartedSecuring the TV
Sony strongly recommends taking measures to prevent the TV from toppling 
over; as unsecured TVs may topple and result in property damage, serious 
bodily injury or even death.
Preventing the TV 
from Toppling❑Secure the TV to a wall and/or stand.
❑Do not allow children to play or climb on furniture and TV sets.
❑Avoid placing or hanging items on the TV.
❑Never install the TV on:
 slippery, unstable and/or uneven surfaces.
 furniture that can easily be...

Getting Started
18
2Secure the TV to the Stand.
Use the optional hardware listed below (not supplied):
 M6 × 12-18mm anchor bolt (screwed into the TV’s Table-Top Stand). 
 A screw or similar (attach it to the TV stand).
 Rope or chain (strong enough to support the weight of the TV). Make 
sure that there is no excess slack in the rope or chain. 
An alternative way to secure the TV is with an optional Sony Support Belt Kit.
3Anchor the TV to the Wall.
Use the hardware listed below (not supplied).
 Two M6...

Getting Started
19
Getting Started
Bundling the 
Connecting CablesYou can bundle the connecting cables with the supplied cable band as 
illustrated below.
Do not bundle the AC power cord with other connecting cables.
 

Getting Started
20
Setting Up the Channel List - Initial Setup
After you finish connecting your TV, you need to run Initial Setup, which 
automatically sets up available channels. The Initial Setup screen appears 
when you turn on your TV for the first time. If you do not want to set up the 
channels at this time, you can do it later by selecting the Auto Program 
option in the Channel settings (see page 29).
1Press   to turn on the TV.
The Initial Setup screen appears.
2Press V/v to highlight the...