Sony Kdl 26ex300 Operating Instructions

							11
Setting up your TV
3Anchor the TV to the Wall
Anchor the TV to the wall by using bolts, wall 
anchor and chain (or rope).
~
 Your TV is shipped with screws attached to the 
rear of the TV. (They are fastened in the screw 
holes for wall mounting.) Be sure to remove the 
upper two screws prior to anchoring the TV on a 
wall.
 Securing the TV to the stand without securing 
the TV and the stand to the wall provides 
minimum protection against the TV toppling 
over. For further protection, be sure to follow the 
three measures recommended.
Organizing the AC power 
cord
Running initial setup
1Complete your cable connections 
before proceeding with the Initial 
Setup.
Connect the TV to your nearest power 
outlet.
2Check the ENERGY SAVING 
SWITCH setting is on (z).
3Press POWER on the TV.
When you switch the TV on for the first 
time, the Language menu appears on 
the screen.
4Follow the instructions on the screen.
~
The ENERGY SAVING SWITCH must be 
on (z) to set the clock and obtain program 
information for the TV Guide.
Home mode sets the TV to display the settings 
optimized for home viewing (this setting is 
ENERGY STAR compliant).
5Select Continue to scan for available 
channels and enable the 
TV Guide On 
Screen® feature. If you receive channels 
from a cable box or satellite receiver 
and do not wish to use the TV’s built-in 
tuner, select 
Skip. 
Selecting 
Skip will disable the TV Guide 
On Screen
 feature, which is only 
available when the TV’s tuner is used.
~
If you skip the channel scan while in the setup 
menus, TV Guide will be disabled.
Anchor bolts (not supplied)
Wall-
mount 
holesRope 
or 
chain 
(not 
supplied)
Wall-anchor 
(not supplied)
POWER
 
						

							12
Detaching the Table-Top 
Stand from the TV
Remove only the screws marked with   on 
the TV.
~
KDL-32EX700 model must remove the stand rear 
cover prior to detaching the Table-Top Stand.
Do not remove the Table-Top Stand for any 
reason other than to install corresponding 
accessories on the TV.
When installing the TV on a wall, remove the four 
screws from the rear of the TV. (They are fastened 
in the screw holes for wall mounting.) Be sure to 
store the removed screws in a safe place, keeping 
them away from children.
When attaching the Table-Top Stand again, be 
sure to fasten the four screws (previously 
removed) to the original holes on the rear of the 
TV.
Do not hold by the Stand Rear Cover while 
carrying the Table-Top Stand to prevent dropping 
the stand which may cause an injury or damage to 
the property.
 
						

							13
Setting up your TV
Using a Wall-Mount Bracket
Your TV can be mounted on a wall using a 
Wall-Mount Bracket (not supplied) out of the 
box as packaged. Some larger size TV may 
require detaching the Table-Top Stand; see 
“Detaching the Table-Top Stand from the TV” 
(page 12). 
Prepare the TV for the Wall-Mount Bracket 
before making cable connections.
For product protection and safety reasons, 
Sony strongly recommends that you use the 
Wall-Mount Bracket designed for your TV 
and the installation should be performed by 
a Sony dealer or licensed contractor.
 Follow the instruction guide provided with 
the Wall-Mount Bracket for your model. 
Sufficient expertise is required in installing 
this TV, especially to determine the 
strength of the wall for withstanding the 
TV’s weight.
 Be sure to use the screws supplied with the 
Wall-mount bracket when attaching the 
mounting hooks to the TV set.
The supplied screws are designed so that 
they are 8 mm to 12 mm in length when 
measured from the attaching surface of the 
mounting hook.
The diameter and length of the screws differ 
depending on the Wall-mount bracket 
model. Use of screws other than those 
supplied may result in internal damage to 
the TV set or cause it to fall, etc.
 Be sure to store the unused screws and 
Table-Top Stand in a safe place until you 
are ready to attach the Table-Top Stand. 
Keep the screws away from small children.
~
Read the supplied Safety Booklet for additional 
safety information.
Installing the TV Against a 
Wall or Enclosed Area
Make sure that your TV has adequate 
ventilation. Allow enough space around the 
TV as shown below. Avoid operating the TV at 
temperatures below 41 °F (5 °C).
~
Inadequate ventilation can lead to overheating of 
the TV and may cause damage to your TV or 
cause a fire.
8-12 mm
Screw 
(supplied with the 
Wall-mount bracket)
Mounting Hook
Hook attachment on rear of TV 
set
(30 cm) 117/8 inches
(6 cm)            inches
4 inches
(10 cm)4 inches
(10 cm)23/8 
Leave at least this much space around the set.
Installed with stand
inches 117/8 
4 inches
(10 cm) 4 inches
(10 cm)
4 inches (10 cm)
(30 cm)
Installed on the wall
Leave at 
least this 
much space 
around the 
set.
Never install the TV set as follows:
Air circulation is blocked.Air circulation is blocked.
Wall Wall
 
						

							14
To watch TV
To watch programs
To use the TV features
Press HOME to display TV Home Menu/
XMB
™ to access TV Settings and other 
media and network related content.
Press OPTIONS to display a list of convenient 
functions and menu shortcuts. The Options menu 
items vary based on current input and/or content.
1Turn on the TV.
1Check the ENERGY SAVING 
SWITCH setting is on (z).
2Press POWER on the TV or on the 
remote control to turn on the TV. (You 
may use the 1 button located on the 
front or back of the remote control.)
2Select a TV channel.
To use the Guide
Press GUIDE to display the TV Guide On 
Screen to view scheduled programs or to 
select a program to watch. Press again to exit 
the Guide. Use with 0-9 and ENT to select 
digital channels. For example, to enter 2.1, 
press , ,  and ENT.
GUIDE
OPTIONS
HOME
0-9
ENT
2 1-2
Settings
TVPicture & DisplayAdjust the picture and screen settingsPress      for:
Picture Adjustments
Ambient Sensor
Screen
Pro Picture Setup
Picture Adjustments
Sound Adjustments
Add to Favorites
Speakers
 
						

							15
To watch TV
To use i-Manual
xWelcome to i-Manual
xBRAVIA TV Features
xWatching TV
Introduces convenient features such as TV 
Guide, Favorites, etc.
xUsing the Home Menu
You can find how to customize your TV 
settings, etc.xFun Features with Connected 
Equipment
Introduces how to connect and enjoy optional 
equipment.
xParts Description
xTroubleshooting
You can find solutions for your problems.
xIndex
~
Images and illustrations may differ from what you are watching on this TV.
Your BRAVIA TV comes with an on-screen 
manual. You can browse your i-Manual anytime 
you need to find the varieties of convenient 
functions.
1Press i-MANUAL.
2Press F/f/G/g/  to navigate and 
select items.
1
2
Welcome to i-Manual
BRAVIA TV  Features
Watching TV
Using the Home Menu
Fun Features with Connected Equipment
Parts Description
Troubleshooting
Index
i-Manual
RETURNBack
 
						

							16
Troubleshooting
The TV will indicate any problems with the STANDBY indicator flashing in red.
When the STANDBY indicator is flashing
The self-diagnosis function is activated. 
1Count how many times the STANDBY indicator flashes between each two second 
break.
For example, the indicator may flash three times, go off for two seconds, then flash again three 
times.
2Press POWER on the TV to turn it off, disconnect the AC power cord, and inform your 
dealer or Sony service center of how the indicator flashes (number of flashes).
When the STANDBY indicator is not flashing
1Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)
2If the problem persists, contact Sony Customer Support (information provided on the 
front cover).
ConditionExplanation/Solution
Picture
There is no picture (screen 
is dark) and no sound.Check the antenna/cable connection.
Connect the TV to the AC power, and press POWER on the TV.
If the STANDBY indicator lights up in red, press POWER on the 
remote control.
Tiny black dots and/or 
bright dots appear on the 
screen.The screen is composed of pixels. Tiny black dots and/or bright 
dots (pixels) on the screen do not indicate a malfunction.
General
The TV’s power cannot be 
turned on.Check to see the (z) mark on the ENERGY SAVING SWITCH 
is pressed.
The TV turns off 
automatically (the TV 
enters standby mode).Check if the Sleep Timer, Timer, or Idle TV Standby is 
activated.
The Auto Shut-off function may be set to On. If Auto 
Shut-off is activated and TV receives no signal, the TV will 
automatically enter standby mode in 15 minutes. Check Auto 
Shut-off is activated under Eco feature of this TV.
The remote does not 
function.Replace the batteries.
Your TV may be in SYNC mode. Press SYNC MENU, select TV 
Control and then select Home (Menu) or Options to control 
the TV.
The “Parental Lock” 
password has been 
forgotten.Enter 4357 for the PIN code. (PIN code 4357 is always accepted.)
Additional Information
 
						

							17
Additional Information
How to Care for Your BRAVIA
Safety is very important, please read and follow the safety documentation (Safety Booklet) 
separately provided.
Unplug the TV and other connected equipment from the wall 
outlet before you begin cleaning your TV.
 Wipe the LCD screen gently with a soft cloth.
 Stubborn stains may be removed with a cloth slightly moistened with a 
solution of mild soap and warm water.
 If using a chemically pretreated cloth, please follow the instruction 
provided on the package.
 Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
 Do not plug in the TV into the wall outlet until the moisture from cleaning has evaporated.
The TV should also be placed on a stable surface to prevent it from toppling over (see page 10). 
If you have young children or pets at home, check regularly to insure the TV is securely fastened. 
 
						

							18
Specifications
*1 For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).
*2 Download Acquisition Mode (DAM) is used for software updates and/or collecting data for TV Guide On Screen.
 Optional accessories availability depends on its stock.
 Design and specifications are subject to change without notice.
Model name KDL-60EX703
60EX701
60EX70052EX703
52EX701
52EX70046EX703
46EX701
46EX70040EX703
40EX70032EX700
System
Television system NTSC: American TV standard 
ATSC (8VSB terrestrial): ATSC compliant 8VSB
QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality)
Channel coverage Analog terrestrial: 2 - 69 / Digital terrestrial: 2 - 69
Analog Cable: 1 - 135 / Digital Cable: 1 - 135
Panel system LCD (Liquid Crystal Display) Panel
Speaker output 10 W + 10 W
Input/Output jacks
CABLE/ANTENNA 75-ohm external terminal for RF inputs
VIDEO IN 1/2 VIDEO / AUDIO
COMPONENT IN 1/2 YP
BPR (Component Video) / Signal format: 480i, 480p, 720p, 1080i, 1080p / AUDIO
HDMI IN 1/2/3/4 HDMI: Video: 480i, 480p, 720p, 1080i, 1080p, 1080/24p
HDMI: Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
AUDIO (HDMI IN 1)
AUDIO OUT 500 mVrms (typical)
DIGITAL AUDIO OUT 
(OPTICAL)PCM/Dolby Digital optical signal
PC IN D-sub 15-pin, analog RGB
PC/HDMI 4 AUDIO IN Stereo mini jack
LAN
10BASE-T/100BASE-TX connector (Connection speed may differ depending on the network environment. 
10BASE-T/100BASE-TX communication rate and communication quality are not guaranteed for this TV.)*1
USB/DLNA Refer to the i-Manual for supported format.
Power and others
Power requirement 110-240 V AC, 50/60 Hz (U.S.A./Canada 120 V AC, 60 Hz)
Power consumption
208 W 142 W 125 W 107 W 91 W
in use
in DAM*
215 W
(You may hear a clicking noise during the download but this is normal.)
in standby less than 0.17 W with 120 V AC and less than 0.23 W with 
240 V ACless than 0.13 W with 120 V AC and less 
than 0.2 W with 240 V AC
Screen size
(inches measured diagonally)60 inches 52 inches 46 inches 40 inches31.5 inches
(32 class)
Display resolution  1,920 dots (horizontal) × 1,080 lines (vertical)
Speaker 
Full range with speaker  (mm)
box (2)  (inches)34 × 160
1 
3/8 × 6 3/8
Dimensions with stand  (mm)
(inches)1,431 × 909 × 38656 3/8 × 35 7/8 × 15 1/41,252 × 805 × 35049 3/8 × 31 3/4 × 13 7/81,118 × 730 × 28044 1/8 × 28 3/4 × 11 1/8985 × 655 × 28038 7/8 × 25 7/8 × 11 1/8811 × 539 × 25032 × 21 1/4 × 9 7/8
without stand  (mm)
(inches)1,431 × 877 × 6656 3/8 × 34 5/8 × 2 5/8 1,252 × 775 × 6549 3/8 × 30 5/8 × 2 5/8 1,118 × 698 × 6544 1/8 × 27 1/2 × 2 5/8985 × 623 × 6438 7/8 × 24 5/8 × 2 5/8 811 × 507 × 6532 × 20 × 2 5/8
wall-mount hole pattern (mm)400 × 300 300 × 300 200 × 200
wall-mount screw size (mm)M6 
(length: refer to diagram on page 13.)
Mass with stand (kg)/(lb.) 38.1/84.0 27.0/59.5 21.3/47.0 17.8/39.3 12.7/28.0
without stand (kg)/(lb.) 31.3/69.0 22.7/50.0 18.4/40.6 14.9/32.9 10.7/23.6
Supplied accessories
See “Checking the accessories” (page 4).
Optional accessories Connecting cables / Support Belt Kit / Wall-Mount Bracket
 
						

							19
Additional InformationFor customers in Canada
This Class B digital apparatus complies with Canadian 
ICES-003.
FCC Related Information
This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause 
harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause 
harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one 
or more of the following measures:
❑Reorient or relocate the receiving antenna.
❑Increase the separation between the equipment and 
receiver.
❑Connect the equipment into an outlet on a circuit 
different from that to which the receiver is connected.
❑Consult the dealer or an experienced radio/TV 
technician for help.
Safety and Regulatory
To prevent radio interference to the licensed service, this 
device is intended to be operated indoors and away from 
windows to provide maximum shielding. Equipment (or its 
transmit antenna) that is installed outdoors is subject to 
licensing.
Only use Wireless LAN indoors when using it with IEEE 
802.11a/n (5 GHz).
High power radars are allocated as primary users (meaning 
they have priority) of 5250-5350 MHz and 5650-
5850 MHz and these radars could cause interference and/or 
damage to this device.
This device uses 5 GHz band for wireless LAN communication and the maximum gain of the antenna in 
this device is 6 dBi.
This equipment complies with FCC/IC radiation exposure 
limits set forth for an uncontrolled environment. This 
equipment should be installed and operated with minimum 
distance 20 cm between the radiator and your body 
(excluding extremities: hands, wrists and feet).
This device and its antenna(s) must not be co-located or 
operating with any other antenna or transmitter except 
Grant condition.
Note
This television includes a QAM demodulator which should 
allow you to receive unscrambled digital cable television 
programming via subscription service to a cable service 
provider. Availability of digital cable television 
programming in your area depends on the type of 
programming and signal provided by your cable service 
provider.
Compatible Wall-Mount Bracket Information
Use the following Sony Wall-Mount Bracket with 
your TV model.
Use with other Wall-Mount Brackets may cause instability 
and could result in property damages or injury.
To Customers
Sufficient expertise is required for TV installations. Be 
sure to subcontract the installation to a Sony dealer or 
licensed contractor and pay adequate attention to safety 
during the installation.
For Customers in the United States
Lamp in this product contains mercury. 
Disposal of these materials may be regulated 
due to environmental considerations. For 
disposal or recycling information, please 
contact your local authorities or the Electronic 
Industries Alliance (www.eiae.org).
Declaration of Conformity
Trade Name: SONY
Model: KDL-60EX703/KDL-52EX703/KDL-46EX703/
KDL-40EX703/KDL-60EX701/KDL-52EX701/
KDL-46EX701/KDL-60EX700/KDL-52EX700/
KDL-46EX700/KDL-40EX700/KDL-32EX700
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
This device complies with part 15 of the FCC rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, 
including interference that may cause undesired 
operation.
Pursuant to FCC regulations, you are cautioned that any 
changes or modifications not expressly approved in this 
manual could void your authority to operate this 
equipment.
Sony TV Model No.
KDL-60EX703
KDL-52EX703
KDL-46EX703
KDL-40EX703
KDL-60EX701
KDL-52EX701
KDL-46EX701
KDL-60EX700
KDL-52EX700
KDL-46EX700
KDL-40EX700
KDL-32EX700
Sony Wall-Mount 
Bracket Model No.SU-WL500