Sony Kdl 22cx32d Operating Instructions

							41 GB
Additional Information
Unit: cm
Figures in the above table may differ slightly depending on the installation.
The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of 
the TV. Refer to “Specifications” (page 42) for its weight.
TV installation dimensions table
Model nameDisplay dimensionsScreen centre 
dimensionLength for each mounting angle
Angle (0°) Angle (20°)
AB CDEFGH
KDL-22CX32D53.0 34.9 10.2 29.0 12.3 21.1 32.6 28.5
125
SU-WL100
Screen centre point
WARNING
Screw and Hook locations diagram/table
Model NameHook location
SU-WL100
KDL-22CX32Db
ba
SU-WL100 Hook location
 
						

							42 GB
Specifications
System
Panel System
LCD (Liquid Crystal Display) Panel
TV SystemDepending on your country/region selection
Analogue: B/G, D/K, L, I
Digital: DVB-T, DVB-C 
Colour/Video SystemAnalogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC [email protected], [email protected]
Channel CoverageAnalogue: 46.25 - 855.25 MHz
Digital: VHF/UHF
Disc formatsDVD+RW, DVD+R, DVD-RW, DVD-R, CD-RW, CD-R
Media formatsDVD video, audio CD, video CD (VCD 1.0/1.1/2.0), S-Video CD
Sound Output5W + 5W
Region codeIndicated on the rear of the TV.
Input/Output jacks
Aerial
75 ohm external terminal for VHF/UHF
/ AV121-pin scart connector including audio/video input, RGB input, S-Video input, and TV audio/video output.
 COMPONENT INSupported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/PB/CB: 0.7 Vp-p, 75 ohms/
PR/CR: 0.7 Vp-p, 75 ohms
 COMPONENT INAudio input (phono jacks)
HDMI IN 1, 2Video: 1080p, 1080/24p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
PC (see page 43)
Analogue audio (minijack) (HDMI 1 only)
AV2Video input (phono jack)
AV2Audio input (phono jacks)
 DIGITAL AUDIO 
OUT (OPTICAL)Digital optical jack (Two channel linear PCM, Dolby Digital)
 AUDIO OUTAudio output (Left/Right) (phono jacks)
PC IN PC Input (15 D-sub) (see page 43)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms, H/V Sync: TTL level
 PC audio input (minijack)
iHeadphones jack
m 1, 2Microphone jack
USB port
CAM (Conditional Access Module) slot
DVDDVD Wavelength: 655 ± 15nm
Power Max: 0.4mW
CD Wavelength: 790 ± 20nm
Power Max: 0.4mW
 
						

							43 GB
Additional Information
*1Energy consumption per year, based on the power consumption of the television operating 4 hours per day for 365 days. 
The actual energy consumption will depend on how the television is used.
*
2Specified standby power is reached after the TV finishes necessary internal processes.
Design and specifications are subject to change without notice.
PC Input Signal Reference Chart for PC IN   and HDMI IN 1/2
 This TV’s PC input does not support Sync on Green or Composite Sync.
 This TV’s PC input does not support interlaced signals.
 This TV’s PC input supports signals in the above chart with a 60 Hz vertical frequency.
Model name KDL-22CX32D
Power and others
Power Requirements
220–240 V AC, 50 Hz
Energy Efficiency ClassC
Screen Size (measured 
diagonally)Approx. 54.8 cm / 22 inches
Power 
consumptionin “Home”/
“Standard” 
mode42.0 W
in “Shop”/
“Vivid” 
mode60 W
Average annual energy 
consumption*161 kWh
Standby Power 
Consumption*20.27 W
Off mode Power 
Consumption0.26 W
Display Resolution1,366 dots (horizontal) × 768 lines (vertical)
Dimensions 
(w × h × d)
(Approx.)(with stand)53.0 × 38.1 × 19.0 cm
(without 
stand)53.0 × 34.9 × 8.1 cm
Mass
(Approx.)(with stand)6.4 kg
(without 
stand)5.9 kg
Supplied AccessoriesRefer to “1: Checking the accessories” on page 4.
Optional AccessoriesSee “Installing the Accessories (Wall-Mount Bracket)” on page 40.
Signals Horizontal (Pixel) Vertical (Line)Horizontal 
frequency 
(kHz)Vertical 
frequency (Hz)Standard
VGA 640 480 31.5 60 VGA
SVGA 800 600 37.9 60 VESA Guidelines
XGA 1024 768 48.4 60 VESA Guidelines
WXGA 1280 768 47.4 60 VESA
WXGA 1280 768 47.8 60 VESA
WXGA 1360 768 47.7 60 VESA
 
						

							44 GB
Troubleshooting
Check whether the 1 (standby) indicator is 
flashing in red.
When it is flashing
The self-diagnosis function is activated. 
Press 1 on the side of the TV to turn it off, 
disconnect the mains lead, and inform your dealer or 
Sony service centre.
When it is not flashing
1Check the items in the tables below.
2If the problem still persists, have your TV 
serviced by qualified service personnel.
z 
 For further information, please contact Sony Customer 
Information Centre at the address or telephone that 
appears on the supplied guarantee.
Picture
No picture (screen is dark) and no sound
 Check the aerial/cable connection.
 Connect the TV to the mains, and press 1 on the side of 
the TV.
 If the 1 (standby) indicator lights up in red, press "/1.
No picture or no menu information from 
equipment connected to the scart connector
 Press   to display the connected equipment list, then 
select the desired input.
 Check the connection between the optional equipment 
and the TV.
Double images or ghosting
 Check the aerial/cable connection.
 Check the aerial location and direction.
Only snow and noise appear on the screen
 Check if the aerial is broken or bent.
 Check if the aerial has reached the end of its serviceable 
life (three to five years in normal use, one to two years 
at the seaside).
Picture or sound noise when viewing a TV 
channel
 Adjust “AFT” (Automatic Fine Tuning) to obtain better 
picture reception (page 34).
Some tiny black points and/or bright points 
appear on the screen
 The picture of a display unit is composed of pixels. Tiny 
black points and/or bright points (pixels) on the screen 
do not indicate a malfunction.
No colour on programmes
 Select “Reset” (page 29).
No colour or irregular colour when viewing a 
signal from the  COMPONENT IN sockets
 Check the connection of the  COMPONENT IN 
sockets and check if each sockets are firmly seated in 
their respective sockets.
Sound
No sound, but good picture
 Press 2 + or % (Mute).
 Check if the “Speakers” is set to “TV Speakers” 
(page 31).
 When using HDMI input with Super Audio CD or DVD-
Audio, DIGITAL AUDIO OUT (OPTICAL) may not 
output audio signals.
Channels
The desired channel cannot be selected
 Switch between digital and analogue mode and select 
the desired digital/analogue channel.
Some channels are blank
 Scrambled/Subscription only channel. Subscribe to the 
pay TV service.
 Channel is used only for data (no picture or sound).
 Contact the broadcaster for transmission details.
Digital channels are not displayed
 Contact a local installer to find out if digital 
transmissions are provided in your area.
 Upgrade to a higher gain aerial.
General
The TV turns off automatically (the TV enters 
standby mode)
 Check if the “Sleep Timer” (page 37) or “Idle TV 
Standby” (page 39) is activated.
 If no signal is received and no operation is performed in 
the TV mode for 15 minutes, the TV automatically 
switches to standby mode.
Distorted picture and/or sound
 Keep the TV away from electrical noise sources such as 
cars, motorcycles, hair-dryers or optical equipment.
 When installing optional equipment, leave some space 
between the optional equipment and the TV.
 Check the aerial/cable connection.
 Keep the aerial/cable TV cable away from other 
connecting cables.
The remote does not function
 Replace the batteries.
HDMI equipment does not appear on “HDMI 
Device List”
 Check that your equipment is compatible with control 
for HDMI.
If “Store Display Mode: On” is displayed on the 
screen
 Your TV is set to “Shop” mode. You need to set “Home” 
for “Location” in the “Auto Start-up” procedure again 
(page 6).
 
						

							45 GB
Additional Information
Television in the UK is going digital, bringing us all more.
Please see overleaf to find out when your area switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover 
in the UK. Digital UK provides impartial information on what people need to do to prepare for the 
move to digital, and when they need to do it.
How the switchover affects your TV equipment:
Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by 
simply plugging it into your aerial socket (check if you can get digital TV through your aerial now, 
or whether youll have to wait until switchover, at www.digitaluk.co.uk).
When the TV switchover happens in your area, there are at least two occasions when you will need 
to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up 
new ones. Digital UK, the body leading the digital TV switchover, will advise you when you need 
to re-tune during the switchover.
Keep this Instruction 
manual safe you’ll
need it
 
						

							46 GB
How to re-tune:
1Press HOME on the remote
2Press F/f to select Settings, then press 
3Press F/f to select Channel Set-up, then press  .
4Press F/f to select Digital Set-up, then press 
5 Press   to select Digital Tuning
6 Press   to select Digital Auto Tuning
7Press G to select OK then press   to start Digital Auto Tuning
8 Follow the on screen instructions.
If you are missing any channels, it may be that they are not available in your area, or that your aerial 
needs upgrading.
If you have any questions, please contact Sony on 0844 8466555 or call Digital UK on 0845 6 50 50 
50 or visit www.digitaluk.co.uk
†Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends. 
Rates may vary for calls from non-BT lines.
 
						

							© 2011 Sony Corporation4-270-482-11(1)
For useful information about Sony products