Sony Kdf 50e2000 Operating Instructions
Here you can view all the pages of manual Sony Kdf 50e2000 Operating Instructions. The Sony manuals for Television are available online for free. You can easily download all the documents as PDF.
Page 31
31 GB Using Optional Equipment Connecting to the TV (rear) (SMARTLINK) DVD player with component output DVD player DecoderDVD recorder VCR Hi-Fi Video game equipment DVD player PC Decoder Digital satellite receiver To connect Do thisPC DConnect to the PC / sockets. It is recommended to use a PC cable with ferrites. Digital satellite receiver or DVD player E, FConnect to the HDMI IN 6 socket or to the HDMI IN 7 socket if the equipment has a HDMI socket. The digital video and audio signals...
Page 32
32
GB
Optimum Viewing AreaFor the best picture quality, try to position the TV set so that you can view the screen from within the areas shown below.Horizontal viewing area
Vertical viewing areaAdditional Information
65
°
65
° KDF-50E2000/
KDF-50E2010:
2.0 m and more
30
°30
°
KDF-50E2000/
KDF-50E2010:2.0 m and more
Page 33
33 GB Additional Information Replacing the lampThe projection lamp, like all lamps, will eventually lose brightness and functionality which affects the overall performance of your TV. How long the lamp maintains its brightness will vary depending upon your usage and environmental conditions. To maintain the quality of your viewing experience, Sony recommends that you replace the lamp (1) after approximately 8,000 hours of use, (2) when the screen becomes dark or the colour looks unusual, (3) when...
Page 34
34 GB 5 Remove the lamp door.Turn the knob counterclockwise to OPEN and pull out the cover. 6 Pull out the lamp.Hook a finger through the loop of the lamp handle and pull the handle upwards. Then pull the lamp straight out..Tips The lamp is very hot immediately after use. Never touch the glass portion of the lamp or the surrounding parts. After the used lamp has cooled, place it into the empty box of the replacement lamp. Never put the used lamp into a plastic bag. 7 Put the new lamp into its...
Page 35
35 GB Additional Information 8 Reattach the lamp door.Turn the knob back to CLOSE and secure the cover. 9 Put the outside lamp cover back in its place.Tips Consult your Sony dealer for a Sony XL-2400 replacement lamp. Take great care when replacing the lamp or plugging in/unplugging the connecting cords. Rough handling may cause the TV to fall, damaging the TV, the TV stand and the floor. A B
Page 36
36 GBSpecificationsDisplay UnitPower Requirements: 220–240 V AC, 50 Hz Screen Size: 50 inches Display Resolution (horizontal x vertical): 1280 dots x 720 lines Power Consumption: 175 W Standby Power Consumption*: 1 W or less * Specified standby power is reached after the TV finishes necessary internal processes. Dimensions (w × h × d): Approx. 1184 x 827 x 408 mm Weight: Approx.29,5 kg Panel SystemLCD (Liquid Crystal Display) PanelTV SystemAnalogue: Depending on your country/region selection: B/G/H,...
Page 37
37 GB Additional Information PC Input SpecificationsPC Input TimingInput signal frequency: Horizontal: 31,4 - 48,4 KHz. Vertical: 59 - 61 Hz. Maximum Resolution: 1024 dots x -768 lines.Preset mode timing table for PC Nº Resolution Graphic mode Horizontal Vertical (dots x lines) frequency (kHz) frequency (Hz)1 640 x 480 VESA 60 31.469 59.940 2 800 x 600 VESA 60 37.879 60.317 3 1024 x 768 VESA 60 48.363 60.004This TV does not support Sync on Green or Composite Sync. If a signal other than in the above...
Page 38
38 GBTroubleshootingCheck whether the 1 (standby) indicator is flashing in red.When it is flashing The self-diagnosis function is activated. 1Measure how long the 1 (standby) indicator flashes and stops flashing. For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. 2Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval). When...
Page 39
39 GB Additional Information Irregular picture when viewing a signal from PC Check PC input socket connection. Connect to PC input socket instead of HDMI IN 6 socket. If the connection is only available through HDMI socket, change the screen resolution to 720p and adjust horizontal and vertical screen size in the display properties settings of PC. Problem Cause/Remedy SoundProblem Cause/RemedyNo sound, but good picture 2 +/– or % (Mute). Check that “TV Speakers” is set to “On” in the “Sound...
Page 40
40 GBIndexNumerics14:9 14 4:3 14 AAerial, connecting 4 AFT 26 Audio Filter 26 Audio Language 29 Audio Type 29 Auto Start-up 25 Auto Tuning analogue and digital channels 6 analogue channels only 25 digital channels only 28 Auto Volume 21 AV Preset 25 AV2 Output 23 BBalance 21 Bass 21 Batteries, inserting into the remote 4 BBE 21 Brightness 20 CCA Module Set-up 29 Category list 15 Channels auto-tuning 6 selecting 13 Skip 27 Clock Set 24 Colour 20 Colour Tone 20 Confirm 27...