Sony Htp 32ss Operating Instructions

							Other Operations/Operations Using the Remote RM-AAU002
masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB08REM_HTR-
10SS-CEL.fm]
model name1[HTR-210SS]
[2-599-618-11(2)]
31GB
You can use the remote RM-AAU002 to operate 
the components in your system.
Inserting batteries into the 
remote
Insert R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment. 
When using the remote, point it at the remote 
sensor   on the receiver.
Tip
Under normal conditions, the batteries should last for 
about 6 months. When the remote no longer operates 
the receiver, replace all batteries with new ones.
Notes
 Do not leave the remote in an extremely hot or humid 
place.
 Do not use a new battery with an old one.
 Do not expose the remote sensor to direct sunlight or 
lighting apparatuses. Doing so may cause a 
malfunction.
 If you don’t use the remote for an extended period of 
time, remove the batteries to avoid possible damage 
from battery leakage and corrosion.* The MASTER VOL +, numeric button 5 and H 
buttons have a tactile dot. Use the tactile dot as a 
reference when operating the receiver and other 
audio/video components.
Operations Using the Remote RM-AAU002
Before you use your 
remote
Remote button 
description
123
46
78
0/10ENTER
9
SYSTEM STANDBY
TV/VIDEO
SLEEPTEST
TONEAV?/1
VIDEO 1 VIDEO 2 DVD SA-CD/CD
2CH A.F.D.
RETURN/EXIT
TV CH –
PRESET –TV CH +
PRESET +
TUNING –
TVTUNING + REPLAY ADVANCEc STEP C DISPLAYMOVIE MUSIC
MEMORY SHIFT
D.SKIP CLEAR ANGLE
AV
MENU TOP MENU/
GUIDE MUTING
TV VOL
MASTER VOL
FM MODEMPXAUDIO
D.TUNING
ANT
JUMPSUBTITLE DUAL MONO
TUNERMAIN MENU
TV ?/1
?/1
>10-
F
Gg
f
ENTER
.
H mM
Xx

						

							masterpage:Left lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB08REM_HTR-
10SS-CEL.fm]
model name1[HTR-210SS]
 [2-599-618-11(2)]
32GB
The tables below show the settings of each 
button.
Remote 
ButtonOperations Function
A.F.D. efReceiver Selects the decoding 
mode for audio sound.
ANGLE 
qsDVD  player Selects viewing angle or 
changes the angles.
ANT 0VCR/
Satellite tunerSelects output signal 
from the antenna 
terminal: TV signal or 
VCR program.
AUDIO 
9DVD player/
Satellite tunerChanges the sound to 
Multiplex or Bilingual 
or Multi channel TV 
sound.
AV 
MENU qdVCR/
DVD player/
Satellite tunerDisplays menu.
AV ?/1 
1VCR/
CD player/
DVD player/
Satellite tuner/
MD deckTurns the audio and 
video components on or 
off.
CLEAR 
eaDVD player/
Satellite tunerClears a mistake when 
you press the incorrect 
numeric buttons or 
returns to continuous 
playback etc.
DISPLAY 
qhReceiver/
CD player/
VCR/
DVD player/
Satellite tuner/
MD deckSelects information 
displayed on the TV 
screen.
D.SKIP 
qaCD player/
DVD playerSkips discs (multi-disc 
changer only).
D.TUNING 
0Receiver Enters direct tuning 
mode.
DUAL 
MONO 8Receiver Selects the language you 
want during digital 
broadcast.
DVD 3Receiver To watch DVD.
ENTER 
qaTV/VCR/
Satellite tunerAfter selecting a 
channel, disc or track 
using the numeric 
buttons, press to enter 
the value.
Remote 
ButtonOperations Function
ENTER wlReceiver/
VCR/
DVD player/
Satellite tuner/
CD player/
MD deckEnters the selection.
FM MODE 
9Receiver Selects FM monaural 
or stereo reception.
JUMP qsSatellite tuner Toggles between the 
previous and the 
current channels.
MAIN 
MENU 5Receiver Selects the menu of 
the receiver.
MASTER 
VOL +/–
qgReceiver/TV Adjusts the master 
volume of the 
receiver.
MEMORY 
qaReceiver Stores the radio 
stations.
MOVIE 6Receiver Selects the pre-
programmed sound 
fields for movie.
MPX 9VCR Select main or sub 
language.
MUSIC 7Receiver Selects the pre-
programmed sound 
fields for music.
MUTING qfReceiver Mutes the sound from 
the receiver.
PRESET +/– 
qjwhReceiver Selects preset stations.
TV/VCR/
Satellite tunerSelect preset channel.
RETURN/
EXIT wjDVD player Returns to the 
previous menu or 
exits the menu.
Satellite tuner Exits the menu.
SA-CD/CD 
4Receiver To listen to Super 
Audio CD or compact 
disc.
SHIFT qsReceiver Selects a memory 
page for presetting 
radio stations or 
tuning to preset 
stations.
GB01COV_HTR-210SS-CEL.book  Page 32  Wednesday, May 18, 2005  10:15 AM
 
						

							masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB08REM_HTR-
10SS-CEL.fm]
model name1[HTR-210SS]
[2-599-618-11(2)]
33GB
Operations Using the Remote RM-AAU002
Remote 
ButtonOperations Function
SLEEP elReceiver Activates the sleep 
function and the 
duration which the 
receiver turns off 
automatically.
SUBTITLE 
0DVD player Changes the subtitles.
SYSTEM 
STANDBY 
(Press AV
?/1 1 and 
?/1 2 at 
the same 
time)Receiver/
TV/VCR/
CD player/
DVD player/
Satellite tuner/
MD deckTurns off the receiver 
and other Sony audio/
video components.
TEST
TONE ekReceiver Outputs test tone.
TOP MENU/
GUIDE e;DVD player Displays DVD title.
Satellite tuner Display guide menu.
TUNER egReceiver To listen to radio 
programs.
TUNING +/–  
ql wfReceiver Scans radio station.
TV wdTV To watch TV 
programs.
TV CH +/– 
qj whTV Selects preset TV 
channels.
TV/VIDEO 
elTV Selects input signal: 
TV input or video 
input.
TV VOL
+/– qgTV Adjusts the volume of 
the TV.
TV ?/1 2TV Turns the TV on or 
off.
VIDEO 1
ejReceiver To watch VCR.
(VTR mode 3)
VIDEO 2
ehReceiver To watch VCR.
(VTR mode 1)
Remote 
ButtonOperations Function
1-9 and 
0/10 esReceiver Use with SHIFT to 
preset radio station or 
tuning to preset 
stations and with 
D.TUNING for 
direct tuning.
CD player/
DVD player/
MD deckSelects track 
numbers. 
0/10 selects track 10.
TV/VCR/
Satellite tunerSelects channel 
numbers.
2CH edReceiver Selects 2CH 
STEREO mode.
>10 eaVCR/
CD player/
DVD player/
Satellite tuner/
MD deckSelects track 
numbers over 10.
-/-- eaTV Selects the channel 
entry mode, either 
one or two digit.
?/1 2Receiver Turns the receiver on 
or off.
c STEP C
REPLAY /
ADVANCE  
wg qkVCR/
DVD playerReplay the previous 
scene or fast forward 
the current scene.
./> 
wh qjVCR/
CD player/
DVD playerSkips tracks.
m/M 
wf qlDVD  player Searches tracks in the 
forward or backward 
direction.
VCR/
CD player/
MD deck/
Tape deckFastforwards or 
rewinds.
H waVCR/
CD player/
DVD player/
MD deck/
Tape deckStarts playback.

						

							masterpage:Left lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB08REM_HTR-
10SS-CEL.fm]
model name1[HTR-210SS]
 [2-599-618-11(2)]
34GB
Notes
 The supplied remote can be used to control the DVD 
recorder if the command modes of the DVD recorder 
and remote’s setting are the same. The initial setting 
for the remote is  “DVD 1”. If you cannot control the 
DVD recorder using the remote, you can change 
either the factory setting of the remote (see 
“Changing the factory setting of an input button” on 
page 34) or the command mode of the DVD recorder 
(refer to separate operating instructions supplied 
with the DVD recorder).  
 Some functions explained in this section may not 
work depending on the model.
 The above explanation is intended to serve as an 
example only. Therefore, depending on the 
component the above operation may not be possible 
or may operate differently than described.
 When you press input buttons (VIDEO 1, VIDEO 2 
or DVD), the input mode of the TV might not switch 
to the corresponding input mode that you want. In 
this case, press TV/VIDEO button to switch the input 
mode of the TV.
 To activate the buttons with orange printing, press 
TV and the button you want simultaneously.
.
If the factory settings of the input buttons do not 
match your system components, you can change 
them. For example, if you have a CD player and 
you do not have a DVD player/DVD recorder, you 
can assign the DVD button to your CD player.
1Hold down the input button whose 
input you want to change (for example, 
DVD).
2Press the corresponding button of the 
component you want to assign to the 
input button (for example, 5 – CD 
player).
The following buttons are assigned to select 
the input:
*Sony VCRs are operated with a VTR 2 or 3 
setting. These correspond to 8 mm and VHS 
respectively.
Now you can use the DVD button to control 
the CD player.
To reset a button to its factory 
setting
Repeat the above procedure.
To reset all the input buttons to 
their factory setting
Press ?/1, TEST  TONE and MASTER VOL – 
at the same time.
Remote 
ButtonOperations Function
X wsVCR/
CD player/
DVD player/
MD deck/
Tape deckPauses playback or 
recording. (Also starts 
recording with 
components in 
recording standby.)
x w;VCR/
CD player/
DVD player/
MD deck/
Tape deckStops playback.
O wjDVD player Returns to the 
previous menu or 
exits the menu.
V/v wkReceiver Selects a menu item.
B/b wkReceiver Adjusts or changes 
the setting.
V/v/B/b wkVCR/
Satellite tuner/
DVD playerSelects a menu item.
Changing the factory 
setting of an input button
To operate Press
VCR (command mode VTR 3*) 1
VCR (command mode VTR 2*) 2
DVD player  or
DVD recorder 
(command mode DVD 1)3
DVD recorder 
(command mode DVD 3)4
CD player 5
MD deck 6
Tape deck B 7
Tuner (this receiver) 8
DSS (Digital Satellite Receiver) 9
DCS (Digital CS Tuner) 0/10
BSD (Digital BS Tuner) -/--
GB01COV_HTR-210SS-CEL.book  Page 34  Wednesday, May 18, 2005  10:15 AM
 
						

							Additional Information
masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
35GB
model name1[HTR-210SS]
[2-599-618-11(2)] On safety
Should any solid object or liquid fall into the cabinet, 
unplug the receiver and have it checked by qualified 
personnel before operating it any further.
On power sources
 Before operating the receiver, check that the 
operating voltage is identical with your local power 
supply. The operating voltage is indicated on the 
nameplate at the rear of the receiver.
 The receiver is not disconnected from the AC power 
source (mains) as long as it is connected to the wall 
outlet, even if the receiver itself has been turned off.
 If you are not going to use the receiver for a long 
time, be sure to disconnect the receiver from the wall 
outlet. To disconnect the AC power cord, grasp the 
plug itself; never pull the cord.
 AC power cord must be changed only at the qualified 
service shop.
On heat buildup
Although the receiver heats up during operation, this is 
not a malfunction. If you continuously use this receiver 
at a large volume, the cabinet temperature of the top, 
side and bottom rises considerably. To avoid burning 
yourself, do not touch the cabinet.
On placement
 Place the receiver in a location with adequate 
ventilation to prevent heat buildup and prolong the 
life of the receiver.
 Do not place the receiver near heat sources, or in a 
place subject to direct sunlight, excessive dust or 
mechanical shock.
 Do not place anything on top of the cabinet that 
might block the ventilation holes and cause 
malfunctions.
 Use caution when placing the receiver or speakers on 
surfaces that have been specially treated (with wax, 
oil, polish, etc.) as staining or discoloration of the 
surface may result.
On operation
Before connecting other components, be sure to turn 
off and unplug the receiver.
If you encounter color irregularity on a 
nearby TV screen
The front and center speakers and the subwoofer are 
magnetically shielded to allow it to be installed near 
a TV set. However, color irregularities may still be 
observed on certain types of
 TV sets. As the surround 
speakers are not magnetically shielded, we 
recommend that you place the surround speakers 
slightly further away from a TV set (page 11).
If color irregularity is observed...
Turn off the TV set once, then turn it on again after 
15 to 30 minutes.
If color irregularity is observed again...
Place the speaker further away from the TV set.
If howling occurs
Reposition the speakers or turn down the volume on 
the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth 
slightly moistened with a mild detergent solution. Do 
not use any type of abrasive pad, scouring powder or 
solvent such as alcohol or benzine.
If you have any question or problem concerning your 
receiver, please consult your nearest Sony dealer.
Additional Information
Precautions
GB01COV_HTR-210SS-CEL.book  Page 35  Wednesday, May 18, 2005  10:15 AM
 
						

							masterpage:Left lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
36GB
model name1[HTR-210SS]
 [2-599-618-11(2)]
If you experience any of the following 
difficulties while using the receiver, use this 
troubleshooting guide to help you remedy the 
problem.
There is no sound or only a very low-level 
sound no matter which component is 
selected.
 Check that the speakers and components are 
connected securely and correctly.
 Check that both the receiver and all components 
are turned on.
 Check that you have selected the correct 
component on the receiver.
 Check that MASTER VOLUME on the receiver is 
not set at 
“VOL MIN”.
 Press MUTING to cancel the muting function.
There is no sound from a specific component.
 Check that the component is connected correctly 
to the audio input jacks for that component.
 Check that the cord(s) used for the connection is 
(are) fully inserted into the jacks on both the 
receiver and the component.
 Check that you have selected the correct 
component on the receiver.
There is no sound from one of the front 
speakers.
 Check that the component is connected correctly 
to the audio input jacks for that component.
 Check that the cord(s) used for the connection is 
(are) fully inserted into the jacks on both the 
receiver and the component.
The left and right sounds are unbalanced or 
reversed.
 Check that the speakers and components are 
connected correctly and securely.
 Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
 Check that the speakers and components are 
connected securely.
 Check that the connecting cords are away from a 
transformer or motor, and at least 3 meters away 
from a TV set or fluorescent light.
 Move your TV away from the audio components.
 The plugs and jacks are dirty. Wipe them with a 
cloth slightly moistened with alcohol.
There is no sound or only a very low-level 
sound is heard from the center or/and 
surround speakers.
 Select a CINEMA STUDIO EX mode (page 24).
 Adjust the speaker level (page 16).
There is no sound from the subwoofer.
 Check that the subwoofer is connected correctly 
and securely.
The surround effect cannot be obtained.
 Make sure the sound field function is on (press 
MOVIE or MUSIC).
 Sound fields do not function for the signals with a 
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is 
not reproduced.
 Check that the playing DVD, etc. is recorded in 
Dolby Digital or DTS format.
 When connecting the DVD player/DVD recorder, 
etc. to the digital input jacks of this receiver, check 
the audio setting (settings for the audio output) of 
the connected component.
The FM reception is poor.
 Use a 75-ohm coaxial cable (not supplied) to 
connect the receiver to an outdoor FM antenna as 
shown below. If you connect the receiver to an 
outdoor antenna, ground it against lightning. To 
prevent a gas explosion, do not connect the ground 
wire to a gas pipe.
Troubleshooting 
ANTENNA
AMU
Receiver
To ground Ground wire 
(not supplied)  Outdoor FM antenna 
GB01COV_HTR-210SS-CEL.book  Page 36  Wednesday, May 18, 2005  10:15 AM
 
						

							Additional Information
masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
37GB
model name1[HTR-210SS]
[2-599-618-11(2)]
Radio stations cannot be tuned in.
 Check that the antennas are connected securely. 
Adjust the antennas and connect an external 
antenna if necessary.
 The signal strength of the stations is too weak 
(when tuning in with automatic tuning). Use direct 
tuning.
 Make sure you set the tuning interval correctly 
(when tuning in AM stations with direct tuning).
 No stations have been preset or the preset stations 
have been cleared (when tuning by scanning 
preset stations). Preset the stations (page 19).
RDS does not work.
 Make sure that you are tuned to an FM RDS 
station.
 Select a stronger FM station.
The RDS information that you want does not 
appear.
 Contact the radio station and find out whether they 
actually provide the service in question. If so, the 
service may be temporarily out of order.
Remote control
The remote does not function.
 The DISPLAY button on the remote is available 
for TUNER input only.
 Point the remote at the remote sensor   on the 
receiver.
 Remove any obstacles in the path between the 
remote and the receiver.
 Replace all the batteries in the remote with new 
ones, if they are weak.
 Make sure you select the correct input on the 
remote.
 To activate the buttons with orange printing, press 
TV and the button you want simultaneously.
 Before you use the V/v/B/b button for receiver 
operation, press MAIN MENU. To operate other 
components, press TOP MENU/GUIDE or AV 
MENU after pressing the function button.
Error message
If there is a malfunction, the display shows a 
message.
PROTECT
Irregular current is output from the speakers.  The 
receiver will automatically turn off after a few 
seconds. Check the speaker connection and turn on 
the power again. If this problem persists, consult 
your nearest Sony dealer.
If you are unable to remedy the 
problem using the 
troubleshooting guide
Clearing the receiver’s memory may remedy the 
problem (page 14). However, note that all 
memorized settings will be reset to their factory 
settings and you will have to readjust all settings 
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing 
the receiver’s memory
To clear See
All memorized settings page 14
Customized sound fields page 27
GB01COV_HTR-210SS-CEL.book  Page 37  Wednesday, May 18, 2005  10:15 AM
 
						

							masterpage:Left lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
38GB
model name1[HTR-210SS]
 [2-599-618-11(2)] Amplifier section
Power Output1)
Models of area code CEL, CEK
(4 ohms 1 kHz, THD 0.7%)
FRONT
2): 70 W/ch
CENTER2): 70 W
SURR2): 70 W/ch
(4 ohms 100 Hz, THD 0.7%)
SUBWOOFER
2): 70 W
(4 ohms 1 kHz, THD 10%)
FRONT
2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
(4 ohms 100 Hz, THD 10%)
SUBWOOFER
2): 100 W
1) Measured under the following conditions:
2) Depending on the sound field settings and the 
source, there may be no sound output.
Inputs (Analog)
Inputs (Digital)
Reproduction frequency range:
28 – 20,000 Hz
Tone
FM tuner section
Tuning range 87.5 - 108.0 MHz 
Antenna FM wire antenna
Antenna terminals 75 ohms, unbalanced
Intermediate Frequency 10.7 MHz
AM tuner section
Tuning range
Models of area code CEL, CEK
With 9-kHz tuning scale:  531 - 1,602 kHz
Antenna Loop antenna
Intermediate Frequency 450 kHz
General
Power requirements
Power consumption
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 × 64 × 337 mm
including projecting parts 
and controls
Mass (Approx.) 3.3 kg
Speaker section
HTD-710SF only
 Front speakers (SS-MSP800)
 Center speaker (SS-CNP800)
 Surround speakers (SS-MSP800B)
Front/center speakers  Full range, magnetically 
shielded
Surround speakers Full range
Speaker units
Front/surround speakers 70 × 100 mm cone type, 
25 mm Nano Fine Dome 
Tweeter
Center speaker 55 × 110 mm cone type, 
25 mm Nano Fine Dome 
Tweeter
Enclosure type Bass reflex
Rated Impedance 4 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers 265 × 1,108 × 265 mm
Center speaker 300 × 76 × 116 mm
Mass (Approx.)
Front/surround speakers 3.5 kg
Center speaker 1.2 kg
Specifications
Area code Power requirements
CEL, CEK 230 V AC, 50 Hz
SA-CD/CD, VIDEO 1, 2 Sensitivity: 1 V
Impedance: 50 kiloohms
DVD (Coaxial) Sensitivity: –
Impedance: 75 ohms
VIDEO 2, SA-CD/CD 
(Optical)Sensitivity: –
Impedance: –
Gain levels ±6 dB, 1 dB step
Area code Power requirements
CEL, CEK 230 V AC, 50/60 Hz
Area code Power consumption
CEL, CEK 110 W
GB01COV_HTR-210SS-CEL.book  Page 38  Wednesday, May 18, 2005  10:15 AM
 
						

							Additional Information
masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
39GB
model name1[HTR-210SS]
[2-599-618-11(2)] HTR-210SS, HTR-110SS, HTP-32SS,
HTD-710SS only
 Front speakers (SS-MSP600L/
SS-MSP600R)
 Center speaker (SS-CNP600)
 Surround speakers (SS-MSP600SL/
SS-MSP600SR)
Front/center speakers  Full range, magnetically 
shielded
Surround speakers Full range
Speaker units 57 mm cone type
Enclosure type Bass reflex
Rated Impedance 4 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers 83 × 180 × 98 mm
Center speaker 250 × 85 × 98 mm
Mass (Approx.)
Front speakers 0.6 kg
Center speaker 0.7 kg
Surround speakers 0.5 kg
Subwoofer (SS-WMSP600)
Speaker system  Magnetically shielded
Speaker unit  160 mm cone type
Enclosure type  Bass reflex
Dimensions (w/h/d) (Approx.)
200 × 379 × 335 mm 
including front panel
Mass (Approx.) 6 kg 
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Speaker connecting cord (5)
Coaxial digital cord (1)
Foot pads (speakers) (20)
 except for HTD-710SF
Foot pads (subwoofer) (4)
Remote commander (1)
R6 (size-AA) batteries (2)
Speakers
 Front speakers (2)
 Center speaker (1)
 Surround speakers (2)
 Subwoofer (1)
Design and specifications are subject to change 
without notice.For details on the area code of the component you 
are using, see page 3.
GB01COV_HTR-210SS-CEL.book  Page 39  Wednesday, May 18, 2005  10:15 AM
 
						

							40GB
masterpage:Right lename[D:\Sony SEM 
5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\9618112\GB09ADD_HTR-
10SS-CEL.fm]
model name1[HTR-210SS]
 [2-599-618-11(2)]
Main unit
Display 2 (22)
DVD (indicator) 5 (17)
INPUT SELECTOR
 qd (17, 18, 
19)
IR (receptor) 8 (31, 37)
MASTER VOLUME qg (16, 17, 
36)MUTING qf (17, 36)
PRESET TUNING + q; (19)
PRESET TUNING – 9 (19)
SA-CD/CD (indicator) 6 (17)
SOUND FIELD qs (27)
TUNER (indicator) 7 (17)
VIDEO 1 (indicator) 3 (17)
VIDEO 2 (indicator) 4 (17)?/1 (power) 1 (14, 16, 18)
; PLII qa (24)
List of button locations and reference pages
How to use this page
Use this page to find the location of buttons that are 
mentioned in the text.
Illustration number
r
    INPUT SELECTOR qd (17, 18, 19)RR
Name of button/part Reference page
ALPHABETICAL ORDER
NUMBERS AND SYMBOLS
12qdqgqs qfqaq;9876543
GB01COV_HTR-210SS-CEL.book  Page 40  Wednesday, May 18, 2005  10:15 AM