Sony Htp 1100 Operating Instructions

							51GB
 
 
 
 
 
 
Using the Remote/Additional Information
Categories and the 
corresponding buttons
a)Sony VCRs are operated with a VTR 2 or VTR 3 
setting which correspond to 8 mm and VHS 
respectively.
b)Sony DVD recorders are operated with a DVD1 or 
DVD3 setting. For details, refer to the operating 
instructions supplied with the DVD recorders.
c)For details on the BD1 or BD3 setting, refer to the 
operating instructions supplied with the Blu-ray 
disc player or Blu-ray disc recorder.
To clear all remote button 
assignments
Press ?/1, DMPORT and MASTER VOL – at 
the same time.
The remote is reset to its factory settings.
Glossary
xDolby Digital
Digital audio encoding/decoding technology 
developed by Dolby Laboratories, Inc. It 
consists of front (Left/Right), center, surround 
(Left/Right) and sub woofer channels. It is a 
designated audio standard for DVD-video and 
also known as 5.1 channel surround. Since 
surround information is recorded and 
reproduced in stereo, more realistic sound with 
fuller presence is delivered than with Dolby 
surround.
xDolby Pro Logic II
This technology converts 2 channel stereo 
recorded audio into 5.1 channel for playback. 
There is a MOVIE mode for movies and 
MUSIC mode for stereo sources such as 
music. Old movies encoded in the traditional 
stereo format can be enhanced with 5.1 
channel surround sound.
xDolby Surround (Dolby Pro 
Logic)
Audio processing technology developed by 
Dolby Laboratories, Inc. Center and mono 
surround information is matrixed into two 
stereo channels. When reproduced, audio is 
decoded and output in 4 channel surround 
sound. This is the most common audio 
processing method for DVD-video.
xDTS Digital Surround
Digital audio encoding/decoding technology 
for theaters developed by DTS, Inc. It 
compresses audio less than Dolby Digital, 
delivering a higher quality sound 
reproduction. Categories Press
VCR (command mode VTR 3)
a)1
VCR (command mode VTR 2)
a)2
DVD player/DVD recorder 
(command mode DVD1)
b)3
DVD recorder 
(command mode DVD3)
b)4
CD player 5
Euro Digital Satellite Receiver 6
DVR (Digital CATV terminal) 7
DSS (Digital Satellite Receiver) 8
Blu-ray disc player 
(command mode BD1)
c)9
Blu-ray disc recorder 
(command mode BD3)
c)0/10
TV -/--
Not assigned ENTER/
MEMORY
Additional Information
continued
 
						

							52GB
xHDMI (High-Definition 
Multimedia Interface)
HDMI is an interface that supports both video 
and audio on a single digital connection. The 
HDMI connection carries standard to high 
definition video signals and multi-channel 
audio signals to audio/video components, such 
as HDMI equipped TVs, in digital form 
without degradation. The HDMI specification 
supports HDCP (High-bandwidth Digital 
Contents Protection), a copy protection 
technology that incorporates coding 
technology for digital video signals.
xSampling frequency
To convert analog audio to digital, analog data 
should be quantified. This process is called 
sampling, and the number of times per second 
the analog data is quantified is called the 
sampling frequency. A standard music CD 
stores data quantified at 44,100 times per 
second, which is expressed as a sampling 
frequency of 44.1 kHz. Generally speaking, a 
higher sampling frequency means better sound 
quality.
Precautions
On safety
Should any solid object or liquid fall into the 
cabinet, unplug the receiver and have it 
checked by qualified personnel before 
operating it any further.
On power sources
 Before operating the receiver, check that the 
operating voltage is identical with your local 
power supply. 
The operating voltage is indicated on the 
nameplate on the back of the receiver.
 The unit is not disconnected from the AC 
power source (mains) as long as it is 
connected to the wall outlet, even if the unit 
itself has been turned off.
 If you are not going to use the receiver for a 
long time, be sure to disconnect the receiver 
from the wall outlet. To disconnect the AC 
power cord, grasp the plug itself; never pull 
the cord.
 The AC power cord must be changed only at 
a qualified service shop.
On heat buildup
Although the receiver heats up during 
operation, this is not a malfunction. If you 
continuously use this receiver at a large 
volume, the cabinet temperature of the top, 
side and bottom rises considerably. To avoid 
burning yourself, do not touch the cabinet.
 
						

							53GB
 
 
 
 
 
 
 
Additional Information
On placement
 Place the receiver in a location with adequate 
ventilation to prevent heat buildup and 
prolong the life of the receiver.
 Do not place the receiver near heat sources, 
or in a place subject to direct sunlight, 
excessive dust, or mechanical shock.
 Do not place anything on top of the cabinet 
that might block the ventilation holes and 
cause malfunctions.
 Do not place the receiver near equipment 
such as a TV, VCR, or tape deck. (If the 
receiver is being used in combination with a 
TV, VCR, or tape deck, and is placed too 
close to that equipment, noise may result, 
and picture quality may suffer. This is 
especially likely when using an indoor 
antenna. Therefore, we recommend using an 
outdoor antenna).
 Use caution when placing the receiver or 
speakers on surfaces that have been specially 
treated (with wax, oil, polish, etc.) as 
staining or discoloration of the surface may 
result.
On operation
Before connecting other components, be sure 
to turn off and unplug the receiver.
If you encounter color 
irregularity on a nearby TV 
screen
The front speakers, center speaker and the sub 
woofer are magnetically shielded to allow it to 
be installed near a TV set. However, color 
irregularities may still be observed on certain 
types of TV sets. As the surround speakers are 
not magnetically shielded, we recommend that 
you place the surround speakers slightly 
further away from TV set (page 11).
If color irregularity is 
observed...
Turn off the TV set, then turn it on again after 
15 to 30 minutes.
If color irregularity is observed 
again...
Place the speaker further away from the TV 
set.
If howling occurs
Reposition the speakers or turn down the 
volume on the receiver.
On cleaning
Clean the cabinet, panel, and controls with a 
soft cloth slightly moistened with a mild 
detergent solution. Do not use any type of 
abrasive pad, scouring powder, or solvent, 
such as alcohol or benzine.
If you have any questions or problems 
concerning your receiver, please consult your 
nearest Sony dealer.
 
						

							54GB
Troubleshooting
If you experience any of the following 
difficulties while using the receiver, use this 
troubleshooting guide to help you remedy the 
problem.
Audio
There is no sound, no matter which 
component is selected, or only a very 
low-level sound is heard.
 Check that the speakers and components 
are connected securely.
 Check that both the receiver and all 
components are turned on.
 Check that MASTER VOLUME is not set 
to “VOL MIN”.
 Press MUTING to cancel the muting 
function.
 Check that you have selected the correct 
component with the input buttons on the 
remote or INPUT SELECTOR on the 
receiver.
 The protective device on the receiver has 
been activated. Turn off the receiver, 
eliminate the short-circuit problem, and 
turn on the power again.
There is no sound from a specific 
component.
 Check that the component is connected 
correctly to the audio input jacks for that 
component.
 Check that the cord(s) used for the 
connection is (are) fully inserted into the 
jacks on both the receiver and the 
component.
 Check that you have selected the correct 
component with the input buttons on the 
remote or INPUT SELECTOR on the 
receiver.
There is no sound from one of the front 
speakers.
 Make sure you have connected to both the 
L and R jacks of an analog component, and 
not only to either the L or R jack. Use an 
audio cord (not supplied).
The source sound input to the HDMI 
jack on the receiver is not output from 
the TV speaker.
 Check the HDMI connection.
 You cannot listen to the Super Audio CD 
by connecting HDMI.
 Depending on the playback component, 
you may need to set up the component. 
Refer to the operating instructions 
supplied with each component.
The left and right sounds are 
unbalanced or reversed.
 Check that the speakers and components 
are connected correctly and securely.
 Adjust the balance parameters using the 
LEVEL menu (page 33).
There is severe hum or noise.
 Check that the speakers and components 
are connected securely.
 Check that the connecting cords are away 
from a transformer or motor, and at least  
3 m away from a TV set or fluorescent 
light.
 Move your audio components away from 
the TV.
 The plugs and jacks are dirty. Wipe them 
with a cloth slightly moistened with 
alcohol.
There is no sound, or only a very low-
level sound is heard from the center/
surround speakers.
 Select a CINEMA STUDIO EX mode 
(page 41).
 Adjust the speaker level (page 26).
There is no sound from the sub woofer.
 Check that the sub woofer is connected 
correctly and securely.
 
						

							55GB
 
 
 
 
 
 
 
Additional Information
The surround effect cannot be 
obtained.
 Make sure you have selected a sound field 
with MOVIE or MUSIC button.
 Sound fields do not function for signals 
with a sampling frequency of more than 
48 kHz.
Dolby Digital or DTS multi channel 
sound is not reproduced.
 Check that the DVD, etc. you are playing 
is recorded in Dolby Digital or DTS 
format.
 When connecting the DVD player, etc., to 
the digital input jacks of this receiver, 
check the audio setting (the settings for the 
audio output) of the connected component.
Video
There is no picture or an unclear 
picture appears on the TV screen or 
monitor.
 Make sure you have connected the video 
output of your video component to the TV.
 Move your audio components away from 
the TV.
The source image input to the HDMI 
jack on the receiver is not output from  
the TV.
 Check the HDMI connection.
 Depending on the playback component, 
you may need to set up the component. 
Refer to the operating instructions 
supplied with each component.
Tu n e r
The FM reception is poor.
 Use a 75-ohm coaxial cable (not supplied) 
to connect the receiver to an outdoor FM 
antenna as shown below. If you connect 
the receiver to an outdoor antenna, ground 
it against lightning. To prevent a gas 
explosion, do not connect the ground wire 
to a gas pipe.
Radio stations cannot be tuned in.
 Check that the antennas are connected 
securely. Adjust the antennas and connect 
an external antenna, if necessary.
 The signal strength of the stations is too 
weak (when tuning in with automatic 
tuning). Use direct tuning (page 44).
 Make sure you set the tuning interval 
correctly (when tuning in AM stations 
with direct tuning).
 No stations have been preset or the preset 
stations have been cleared (when tuning 
by scanning preset stations). Preset the 
stations (page 45).
RDS does not work.a)
 Make sure that you are tuned to an FM 
RDS station.
 Select a stronger FM station.
ANTENNA
AM
Receiver
To groundGround wire 
(not supplied)  Outdoor FM antenna 
continued
 
						

							56GB
The RDS information that you want 
does not appear.a)
 Contact the radio station and find out 
whether they actually provide the service 
in question. If so, the service may be 
temporarily out of order.
a)Models of area code CEL, CEK only.
Remote control
The remote does not function.
 For receiver operation, you can only use 
the DISPLAY button when the TUNER 
input is selected.
 Point the remote at the remote sensor on 
the receiver.
 Remove any obstacles in the path between 
the remote and the receiver.
 Replace all the batteries in the remote with 
new ones, if they are weak.
 Make sure you select the correct input on 
the remote.
 The VIDEO 3 button on the remote is not 
available for receiver operation.
 
Error messages
If there is a malfunction, the display shows a 
message. You can check the condition of the 
system by the message. Refer to the following 
table to solve the problem. If any problem 
persists, consult your nearest Sony dealer.
If an error message appears while you perform 
Auto Calibration, see “Error and warning 
codes” (page 24) to solve the problem.
PROTECT
Irregular current is output from the 
speakers. The receiver will automatically 
turn off after a few seconds. Check the 
speaker connection and turn on the power 
again.
If you are unable to remedy the 
problem using the 
troubleshooting guide
Clearing the receiver’s memory may remedy 
the problem (page 21). However, note that all 
memorized settings will be reset to their 
factory settings and you will have to readjust 
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if 
service personnel changes some parts during 
repair, these parts may be retained.
Reference sections for clearing 
the receiver’s memory
To  c l e a r S e e
All memorized settings page 21
Customized sound fields page 43
 
						

							57GB
 
 
 
 
 
 
 
Additional Information
Specifications
Amplifier section
HT-SF1100 only
Power Output1)
Stereo mode (rated) 70 W + 70 W  
(4 ohms at 1 kHz,  
THD 1%)
Surround mode (reference) 
RMS Output 
FRONT
2): 143 W/ch
 (With SS-MSP2000)
CENTER
2): 143 W
(With SS-CNP2000)
SUR
2): 143 W/ch
(With SS-SRP2000)
SUBWOOFER
2): 285 W
(With SS-WP2000)
HT-SS1100 only
Power Output
1)
Stereo mode (rated) 70 W + 70 W 
(4 ohms at 1 kHz,  
THD 1%)
Surround mode (reference)
RMS Output 
FRONT
2): 143 W/ch
 (With SS-MSP1100)
CENTER
2): 143 W
(With SS-CNP1100)
SUR
2): 143 W/ch
(With SS-SRP1100)
SUBWOOFER
2): 285 W
(With SS-WP1100)
1)Measured under the following conditions:
2)Reference power output for front, center, surround 
speakers and subwoofer. Depending on the sound 
field settings and the source, there may be no 
sound output.
Inputs 
Analog Sensitivity: 1 V/50 kohms
Digital 
(Coaxial) Impedance: 75 ohms
Tone
Gain levels ±6 dB, 1 dB step
Reproduction frequency range:
28 – 20,000 Hz
FM tuner sectionTuning range 87.5 - 108.0 MHz
Antenna FM wire antenna
Antenna terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner sectionTuning range
Models of area code CEL, CEK
With 9-kHz tuning scale:
531 – 1,602 kHz
Antenna Loop antenna
Intermediate frequency 
450 kHz
GeneralPower requirements
Power output (DIGITAL MEDIA PORT)
DC OUT: 5 V, 700 mA
Power consumption
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 × 66.5 × 335 mm  
including projecting parts 
and controls
Mass (Approx.) 3.6 kg
Area code Power requirements
CEL, CEK 230 V AC, 50 Hz
Area code Power requirements
CEL, CEK 230 V AC, 50/60 Hz
Area code Power consumption
CEL, CEK 110 W
continued
 
						

							58GB
Speaker section
HT-SF1100 only
 Front speakers (SS-MSP2000)
 Center speaker (SS-CNP2000)
 Surround speakers (SS-SRP2000)
Front speakers  2 way, magnetically 
shielded
Center speaker Full range, magnetically 
shielded
Surround speakers Full range
Speaker units
Front speakers 65 mm cone type,  
25 mm Balance Dome 
Tweeter
Center speaker 65 mm cone type
Surround speakers 65 mm cone type
Enclosure type Bass reflex
Rated Impedance 2.7 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers
92 × 538 × 74 mm 
300 × 1,229 (max.) ×  
300 mm with stand
Center speaker 260 × 91 × 80 mm
Mass (Approx.)
Front/surround speakers
1.0 kg 
2.8 kg with stand
Center speaker 0.6 kg
Subwoofer (SS-WP2000)
Speaker system  Magnetically shielded
Speaker unit  160 mm cone type
Enclosure type  Bass reflex
Rated Impedance 1.3 ohms
Dimensions (w/h/d) (Approx.)
196 × 320 × 400 mm 
including front panel
Mass (Approx.) 5.6 kg 
HT-SS1100 only
 Front speakers (SS-MSP1100)
 Center speaker (SS-CNP1100)
 Surround speakers (SS-SRP1100)
Front/center speakers  
Full range, magnetically 
shielded
Surround speakers Full range
Speaker units 57 mm cone type
Enclosure type Bass reflex
Rated Impedance 2.7 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers 
80 × 150 × 88 mm
Center speaker 250 × 85 × 88 mm
Mass (Approx.)
Front speakers 0.5 kg
Center speaker 0.7 kg
Surround speakers 0.4 kg
Subwoofer (SS-WP1100)
Speaker system  Magnetically shielded
Speaker unit  160 mm cone type
Enclosure type  Bass reflex
Rated Impedance 1.3 ohms
Dimensions (w/h/d) (Approx.)
200 × 382 × 337 mm 
including front panel
Mass (Approx.) 4.5 kg 
 
						

							59GB
 
 
 
 
 
 
 
Additional Information
Supplied speakers Front speakers (2)
 Center speaker (1)
 Surround speakers (2)
 Sub woofer (1)
Supplied accessoriesFM wire antenna (1)
AM loop antenna (1)
Remote commander RM-AAU017 (1)
R6 (size-AA) batteries (2)
Optimizer microphone (ECM-AC2 or  
ECM-AC2a) (1)
Speaker cords
 Long (2)
 Short (3)
Coaxial digital cord (1)
Foot pads
 Speakers
– HT-SS1100 only (20)
– HT-SF1100 only (4)
 Sub woofer (4)
Design and specifications are subject to 
change without notice.For details on the area code of the 
component you are using, see page 3.
 
						

							Sony Corporation   Printed in Malaysia
Index
Numerics
2 channel  42
2CH STEREO  42
5.1 channel  11
A
AUTO CALIBRATION  22
AUTO FORMAT DIRECT 
(A.F.D.)  38
B
Blu-ray disc player
connecting  18
C
CD player
connecting  15
playback  28
D
Digital Cinema Sound 
(DCS)  41
DIGITAL MEDIA PORT
connecting  48
Dolby Digital  51
DVD player
connecting  16
playback  29
DVD recorder
connecting  16
E
Error messages  56
H
HDMI
connecting  18
I
Initial setup  21
M
Menu
A. CAL  38
AU D I O  35
LEVEL  33
SUR  34
SYSTEM  36
TONE  34
TUNER  35
Muting  27
R
RDS  46
S
Satellite tuner
connecting  16
Selecting
component  27
sound field  40
Sleep Timer  50
Sound fields
resetting  43
selecting  40
Speakers
connecting  14
installing  11
Super Audio CD player
connecting  15
playback  28
T
TEST TONE  26
Tu ner
connecting  20
Tuning
automatically  43
directly  44
to preset stations  46
V
VCR
connecting  16