Sony Htp 1100 Operating Instructions

21GB
Getting Started5: Preparing the receiver 
and the remote
Connect the AC power cord to a wall outlet.Before using the receiver for the first time, 
initialize the receiver by performing the 
following procedure. This procedure can also 
be used to return settings you have made to 
their factory defaults. 
Be sure to use the buttons on the receiver for 
this operation.
1Press ?/1 to turn off the 
receiver.
2Hold down ?/1 for 5 seconds.
“INITIAL” appears on the display.
The following items are reset to...

22GB
Insert two R6 (size-AA) batteries in the  
RM-AAU017 remote commander.
Observe the correct polarity when installing 
batteries.
Notes
 Do not leave the remote in an extremely hot or 
humid place.
 Do not use a new battery with old ones.
 Do not mix alkaline batteries and other kinds of 
batteries.
 Do not expose the remote sensor to direct sunlight 
or lighting apparatuses. Doing so may cause a 
malfunction.
 If you do not intend to use the remote for an 
extended period of time, remove the...

23GB
Getting Started
Note
If the Muting function is on when we perform Auto 
Calibration, it will turn off automatically.
Example: HT-SS1100
1Connect the supplied optimizer 
microphone to the AUTO CAL 
MIC jack on the front panel.
2Set up the optimizer 
microphone.
Place the optimizer microphone at your 
listening position.You can also use a stool 
or tripod so that the optimizer 
microphone remains at the same height as 
your ears.
Tips
 Be sure to remove any obstacles in the path 
between the...

24GB
When measurement ends, “COMPLETE” 
appears on the display and the settings are 
registered.
After you have finished
Disconnect the optimizer microphone from the 
receiver.
Note
Auto Calibration cannot detect the sub woofer. 
Therefore, all sub woofer settings will be 
maintained.
Tips
 When Auto Calibration starts:
– Stand some distance from the speakers and the 
listening position to avoid measurement failure. 
This is because test signals are output from the 
speakers during measurement.
– Avoid...

25GB
Getting Started
Warning codes
During Auto Calibration, the warning code 
provides information on the measurement 
result. The warning code will appear on the 
display cyclically as follows:
Warning code t blank display t (warning 
code t blank display)
b) t PUSH t blank 
display t ENTER
b)Appears when there are more than one warning 
code.
You can choose to ignore the warning code as 
the Auto Calibration function will 
automatically adjust the settings. You can also 
change the settings manually....

26GB
7: Adjusting the speaker 
levels and balance 
(TEST TONE)
You can adjust the speaker levels and balance 
while listening to the test tone from your 
listening position.
Tip
The receiver employs a test tone with a frequency 
centered at 800 Hz.
1Press AMP MENU.
“1-LEVEL” appears on the display.
2Press  or b to enter the 
menu.
3Press V/v repeatedly to select 
“T. TONE”.
4Press  or b to enter the 
parameter.
5Press V/v repeatedly to select 
“T. TONE Y”.
The test tone is output from each speaker 
in...

27GB
 
Playback
Selecting a component
1
Press the input button to select 
a component.
You can also use INPUT SELECTOR on 
the receiver. 
The selected input appears on the display.
2Turn on the component and 
start playback.
3Press MASTER VOL +/– to 
adjust the volume.
You can also use MASTER VOLUME on 
the receiver.
To mute the sound
Press MUTING.
The muting function will be canceled when 
you do the following.
 Press MUTING again.
 Increase the volume.
 Turn off the receiver.
To avoid damaging your...

28GB
Listening/Watching a component
Listening to a Super Audio CD/CD
DMPORT VIDEO 1 VIDEO 2/BD DVD SAT TV SA-CD/CD TUNER
AUTO CAL MICINPUT SELECTORPRESET TUNINGSOUND FIELD MUTING?/1123
46
78
0/10ENTER9
SYSTEM STANDBYTV INPUT
SLEEPDMPORTTV ?/1 
AV ?/1VIDEO 1 VIDEO 2 VIDEO 3 DVD
2CH A.F.D.
RETURN/EXIT
TV CH –
PRESET –TV CH +
PRESET +
TUNING –
TVTUNING +REPLAY ADVANCEMENU MOVIE MUSIC
MEMORY DVD MENU
FM MODE CLEARTOOLS DISPLAYMUTING
TV VOL
MASTER VOLAUTO CAL
D.TUNING
D.SKIP AMP MENU SAT TV SA-CD/CD TUNER...

29GB
 
Playback
Watching a DVD
123
46
78
0/10ENTER9
SYSTEM STANDBYTV INPUT
SLEEPDMPORTTV ?/1 
AV ?/1VIDEO 1 VIDEO 2 VIDEO 3 DVD
2CH A.F.D.
RETURN/EXIT
TV CH –
PRESET –TV CH +
PRESET +
TUNING –
TVTUNING +REPLAY ADVANCEMENU MOVIE MUSIC
MEMORY DVD MENU
FM MODE CLEARTOOLS DISPLAYMUTING
TV VOL
MASTER VOLAUTO CAL
D.TUNING
D.SKIP AMP MENU SAT TV SA-CD/CD TUNER
?/1
-
F
Gg
f
.H mM
Xx10/
DMPORT VIDEO 1 VIDEO 2/BD DVD SAT TV SA-CD/CD TUNER
AUTO CAL MICINPUT SELECTORPRESET TUNINGSOUND FIELD MUTING?/1MASTER VOLUME
2...

30GB
Navigating through 
menus
By using the amplifier menus, you can make 
various adjustments to customize the receiver.
1Press AMP MENU.
“1-LEVEL” appears on the display.
2Press V/v repeatedly to select 
the menu you want.
3Press  or b to enter the 
menu.
4Press V/v repeatedly to select 
the parameter you want to 
adjust.
5Press  or b to enter the 
parameter.
6Press V/v repeatedly to select 
the setting you want.
The setting is entered automatically.
To return to the previous 
display
Press B.
To exit...