Sony Ht Sf2300 Operating Instructions

							61GB
 
 
 
 
 
 
Other Operations
You can listen to the sound from the 
component connected through the DIGITAL 
MEDIA PORT adapter to the DMPORT jack 
on the receiver.
You can also view the images on the TV 
screen by connecting the video output of the 
DIGITAL MEDIA PORT adapter to the video 
input of the TV.
To detach the DIGITAL MEDIA PORT 
adapter from DMPORT jack
Press and hold both sides of the connector and 
then pull out the connector.
Notes
 When connecting the DIGITAL MEDIA PORT 
adapter, be sure the connector is inserted with the 
arrow mark facing toward the arrow mark on the 
DMPORT jack.
 Be sure to make DMPORT connections firmly, 
insert the connector straight in.
 As the connector of the DIGITAL MEDIA PORT 
adapter is fragile, be sure to handle with care when 
placing or moving the receiver.
1Press DMPORT.
You can also use the INPUT SELECTOR 
on the receiver to select “DMPORT”.
2Start playback of the connected 
component.
The sound is played back on the receiver 
and the image appears on the TV.
For details, refer to the operating 
instructions supplied with the DIGITAL 
MEDIA PORT adapter.
Notes
 Depending on the type of DIGITAL MEDIA 
PORT adapter, you can operate the connected 
component by using the remote. For details on 
remote button operation, see page 10.
 Be sure you have made the video connection from 
DIGITAL MEDIA PORT adapter to the TV  
(page 61).
Connecting the DIGITAL MEDIA 
PORT adapter
COAX IN AUDIO INDV D
DVD INSAT INBD INOUT
SA-CD/CDAUDIO INAUDIO INVIDEO 1
DIGITALHDMI
R
L
R
L
TV
DC5V      700mA MAX 
DMPORT
TV
DIGITAL 
MEDIA PORT 
adapter
* The type of connector varies depending on the 
DIGITAL MEDIA PORT adapter.  
For details, see the operating instructions supplied 
with the DIGITAL MEDIA PORT adapter.
AVideo cord (not supplied)A
Listening/watching a connected 
component through DMPORT 
connection
21RT
DMPO
DC5V      700m
A   MAX 
1
continued
 
						

							62GB
Tip
When listening to MP3 or other compressed music 
using a portable audio source, you can enhance the 
sound. Press MUSIC repeatedly to select 
“PORTABLE” (page 46).Using the Sleep Timer
You can set the receiver to turn off 
automatically at a specified time.
Press SLEEP repeatedly while the 
power is on.
Each time you press the button, the display 
changes cyclically as follows:
2-00-00 t 1-30-00 t 1-00-00 t 0-30-00 
t OFF
When sleep timer is activated, the display dims 
and “SLEEP” indicator lights up.
Note
If you press any buttons on the remote or receiver 
after the display dims, the display brightens up. 
After a while, the display dims again if no button is 
pressed. 
Tip
To check the remaining time before the receiver 
turns off, press SLEEP. The remaining time appears 
on the display. If you press SLEEP again, the sleep 
timer will be canceled.
 
						

							63GB
 
 
 
 
 
 
 
Using the Remote
Changing button 
assignments
You can change the factory settings of the 
input buttons to suit the components in your 
system. For example, if you connect a DVD 
recorder to the VIDEO 1 jacks on the receiver, 
you can set the VIDEO 1 button on this remote 
to control the DVD recorder.
1Hold down the input button of 
which you want to change the 
assignment.
Example: Hold down VIDEO 1.
2Referring to the table below, 
press the corresponding 
button for the category you 
want.
Example: Press 4.
Now you can use the VIDEO 1 button to 
control the DVD recorder.
Categories and the 
corresponding buttons
a)Sony VCRs are operated with a VTR 2 or VTR 3 
setting which correspond to 8 mm and VHS 
respectively.
b)Sony DVD recorders are operated with a DVD1 or 
DVD3 setting. For details, refer to the operating 
instructions supplied with the DVD recorders.
c)For details on the BD1 or BD3 setting, refer to the 
operating instructions supplied with the Blu-ray 
disc player or Blu-ray disc recorder.
To clear all remote button 
assignments
Press ?/1, DMPORT and MASTER VOL – at 
the same time.
The remote is reset to its factory settings.
Using the Remote
Categories Press
VCR (command mode  
VTR 3)
a)1
VCR (command mode  
VTR 2)
a)2
DVD player/DVD recorder 
(command mode DVD1)
b)3
DVD recorder 
(command mode DVD3)
b)4
CD player 5
Euro Digital Satellite 
Receiver6
DVR (Digital CATV 
terminal)7
DSS (Digital Satellite 
Receiver)8
Blu-ray disc player 
(command mode BD1)
c)9
Blu-ray disc recorder 
(command mode BD3)
c)0/10
TV
z (RM-
AAU022 only)
-/-- (RM-
AAU023 only)
Not assigned ENTER/
MEMORY
 
						

							64GB
Glossary
xCinema Studio EX
A surround sound mode that can be regarded 
as the compilation of Digital Cinema Sound 
technology, delivers the sound of a dubbing 
theater using three technologies: “Virtual 
Multi Dimensions”, “Screen Depth 
Matching”, and “Cinema Studio 
Reverberation”. 
“Virtual Multi Dimensions”, the virtual 
speaker technology, creates a virtual multi-
surround environment with actual speakers up 
to 7.1 channels, and brings the surround sound 
experience of a theater with the latest facilities 
into your home.
“Screen Depth Matching” reproduces treble 
attenuation, fullness, and depth of sound 
usually created in a theater using sound 
emission from behind the screen. This is then 
added to the front and center channels.
“Cinema Studio Reverberation” reproduces 
the sound characteristics of state-of-the-art 
dubbing theaters and recording studios, 
including Sony Pictures Entertainment’s 
dubbing studios. There are three modes, A/B/
C, available according to the studio type.
xDigital Cinema Sound (DCS)
A unique sound reproduction technology for 
home theater developed by Sony, in 
cooperation with Sony Pictures Entertainment, 
for enjoying the exciting and powerful sound 
of movie theaters at home. With this “Digital 
Cinema Sound” developed by integrating a 
DSP (Digital Signal Processor) and measured 
data, the ideal sound field intended by 
filmmakers can be experienced at home.
xDolby Digital
Digital audio encoding/decoding technology 
developed by Dolby Laboratories, Inc. It 
consists of front (Left/Right), center, surround 
(Left/Right) and subwoofer channels. It is a 
designated audio standard for DVD-video and 
also known as 5.1 channel surround. Since 
surround information is recorded and 
reproduced in stereo, more realistic sound with 
fuller presence is delivered than with Dolby 
surround.
xDolby Pro Logic II
This technology converts 2 channel stereo 
recorded audio into 5.1 channel for playback. 
There is a MOVIE mode for movies and 
MUSIC mode for stereo sources such as 
music. Old movies encoded in the traditional 
stereo format can be enhanced with 5.1 
channel surround sound.
xDolby Surround (Dolby Pro 
Logic)
Audio processing technology developed by 
Dolby Laboratories, Inc. Center and mono 
surround information is matrixed into two 
stereo channels. When reproduced, audio is 
decoded and output in 4 channel surround 
sound. This is the most common audio 
processing method for DVD-video.
xDTS Digital Surround
Digital audio encoding/decoding technology 
for theaters developed by DTS, Inc. It 
compresses audio less than Dolby Digital, 
delivering a higher quality sound 
reproduction.
Additional Information
 
						

							65GB
 
 
 
 
 
 
 
 
Additional Information
xHDMI (High-Definition 
Multimedia Interface)
HDMI (High-Definition Multimedia 
Interface) is an interface that supports both 
video and audio on a single digital connection, 
allowing you to enjoy high quality digital 
picture and sound. The HDMI specification 
supports HDCP (High-bandwidth Digital 
Contents Protection), a copy protection 
technology that incorporates coding 
technology for digital video signals.
xL.F.E. (Low Frequency Effects)
Sound effects of low frequencies which are 
output from a subwoofer in Dolby Digital or 
DTS, etc. By adding a deep bass with a 
frequency between 20 to 120 Hz, audio 
becomes more powerful.
xSampling frequency
To convert analog audio to digital, analog data 
should be quantified. This process is called 
sampling, and the number of times per second 
the analog data is quantified is called the 
sampling frequency. A standard music CD 
stores data quantified at 44,100 times per 
second, which is expressed as a sampling 
frequency of 44.1 kHz. Generally speaking, a 
higher sampling frequency means better sound 
quality.
xTSP (Time Stretched Pulse)
A TSP signal is a highly precise measuring 
signal that utilizes impulse energy, measuring 
a wide band, from low to high, in a short 
period.
The amount of energy used to measure signals 
is important to ensure measurement accuracy 
in a normal indoor environment. Using TSP 
signals makes it possible to measure signals 
effectively.
xx.v.Colour
x.v.Colour is a more familiar term for the 
xvYCC standard proposed by Sony, and is a 
trademark of Sony. xvYCC is an international 
standard for colour space in video. 
This standard can express a wider colour range 
than the currently used broadcast standard.
Precautions
On safety
Should any solid object or liquid fall into the 
cabinet, unplug the receiver and have it 
checked by qualified personnel before 
operating it any further.
On power sources
 Before operating the receiver, check that the 
operating voltage is identical with your local 
power supply. 
The operating voltage is indicated on the 
nameplate on the back of the receiver.
 The unit is not disconnected from the AC 
power source (mains) as long as it is 
connected to the wall outlet, even if the unit 
itself has been turned off.
 If you are not going to use the receiver for a 
long time, be sure to disconnect the receiver 
from the wall outlet. To disconnect the AC 
power cord, grasp the plug itself; never pull 
the cord.
 (Models of area code U, UC, CA only)  
One blade of the plug is wider than the other 
for the purpose of safety and will fit into the 
wall outlet only one way. If you are unable to 
insert the plug fully into the outlet, contact 
your dealer.
 The AC power cord must be changed only at 
a qualified service shop.
On heat buildup
Although the receiver heats up during 
operation, this is not a malfunction. If you 
continuously use this receiver at a large 
volume, the cabinet temperature of the top, 
side and bottom rises considerably. To avoid 
burning yourself, do not touch the cabinet.
continued
 
						

							66GB
On placement
 Place the receiver in a location with adequate 
ventilation to prevent heat buildup and 
prolong the life of the receiver.
 Do not place the receiver near heat sources, 
or in a place subject to direct sunlight, 
excessive dust, or mechanical shock.
 Do not place anything on top of the cabinet 
that might block the ventilation holes and 
cause malfunctions.
 Do not place the receiver near equipment 
such as a TV, VCR, or tape deck. If the 
receiver is being used in combination with a 
TV, VCR, or tape deck, and is placed too 
close to that equipment, noise may result, 
and picture quality may suffer. This is 
especially likely when using an indoor 
antenna. Therefore, we recommend using an 
outdoor antenna.
 Use caution when placing the receiver or 
speakers on surfaces that have been specially 
treated (with wax, oil, polish, etc.) as 
staining or discoloration of the surface may 
result.
On operation
Before connecting other components, be sure 
to turn off and unplug the receiver.
If you encounter color 
irregularity on a nearby TV 
screen
The front speakers and center speaker are 
magnetically shielded to allow it to be 
installed near a TV set. However, color 
irregularities may still be observed on certain 
types of TV sets. As the surround speakers and 
subwoofer are not magnetically shielded, we 
recommend that you place the surround 
speakers and subwoofer slightly further away 
from TV set (page 14).
If color irregularity is 
observed...
Turn off the TV set, then turn it on again after 
15 to 30 minutes.
If color irregularity is observed 
again...
Place the speaker further away from the TV 
set.
If howling occurs
Reposition the speakers or turn down the 
volume on the receiver.
On cleaning
Clean the cabinet, panel, and controls with a 
soft cloth slightly moistened with a mild 
detergent solution. Do not use any type of 
abrasive pad, scouring powder, or solvent, 
such as alcohol or benzine.
If you have any questions or problems 
concerning your receiver, please consult your 
nearest Sony dealer.
 
						

							67GB
 
 
 
 
 
 
 
 
Additional Information
Troubleshooting
If you experience any of the following 
difficulties while using the receiver, use this 
troubleshooting guide to help you remedy the 
problem.
Audio
There is no sound, no matter which 
component is selected, or only a very 
low-level sound is heard.
 Check that the speakers and components 
are connected securely.
 Check that both the receiver and all 
components are turned on.
 Check that MASTER VOLUME is not set 
to “VOL MIN”.
 Press MUTING to cancel the muting 
function.
 Check that you have selected the correct 
component with the input buttons.
 The protective device on the receiver has 
been activated. Turn off the receiver, 
eliminate the short-circuit problem, and 
turn on the power again.
 Check that the IN MODE setting is 
correct.
There is no sound from a specific 
component.
 Check that the component is connected 
correctly to the audio input jacks for that 
component.
 Check that the cord(s) used for the 
connection is (are) fully inserted into the 
jacks on both the receiver and the 
component.
There is no sound from one of the front 
speakers.
 Make sure you have connected to both the 
L and R jacks of an analog component, and 
not only to either the L or R jack. Use an 
audio cord (not supplied).
There is no sound from digital sources 
(from COAXIAL or OPTICAL input jack).
 Check that the IN MODE is set to 
“AUTO”.
The left and right sounds are 
unbalanced or reversed.
 Check that the speakers and components 
are connected correctly and securely.
 Adjust the balance parameters using the 
LEVEL menu (page 39).
There is severe hum or noise.
 Check that the speakers and components 
are connected securely.
 Check that the connecting cords are away 
from a transformer or motor, and at least  
3 meters (10 feet) away from a TV set or 
fluorescent light.
 Move your audio components away from 
the TV.
 The plugs and jacks are dirty. Wipe them 
with a cloth slightly moistened with 
alcohol.
There is pop noise from a specific 
component connected to this receiver 
when you turn on the component.
 Check that the IN MODE is set to 
“AUTO” for the selected input (page 60).
There is no sound, or only a very low-
level sound is heard from the center/
surround speakers.
 Select a CINEMA STUDIO EX mode 
(page 47).
 Adjust the speaker level (page 30).
 Check that the speakers are connected 
securely.
continued
 
						

							68GB
There is no sound from the subwoofer.
 Check that the subwoofer is connected 
correctly and securely.
The surround effect cannot be 
obtained.
 Make sure the sound field function is on 
(press MOVIE, or MUSIC).
 Sound fields do not function for signals 
with a sampling frequency of more than 
48 kHz.
Dolby Digital or DTS multi channel 
sound is not reproduced.
 Check that the DVD, etc. you are playing 
is recorded in Dolby Digital or DTS 
format.
 When connecting the DVD player, etc., to 
the digital input jacks of this receiver, 
check the audio setting (the settings for the 
audio output) of the connected component.
There is no sound from the component 
connected to the DIGITAL MEDIA PORT 
adapter.
 Adjust the volume of this receiver.
 The DIGITAL MEDIA PORT adapter 
and/or component is not connected 
correctly. Turn off the receiver, then 
reconnect the DIGITAL MEDIA PORT 
adapter and/or component.
 Check the DIGITAL MEDIA PORT 
adapter and/or component device to make 
sure it supports this receiver.
Video
There is no picture or an unclear 
picture appears on the TV screen or 
monitor.
 Make sure you have connected the video 
output of your video component to the TV.
 Move your audio components away from 
the TV.
 Depending on the DIGITAL MEDIA 
PORT adapter, video output may not be 
possible.
HDMI
The source sound input to the HDMI 
jack on the receiver is not output from 
the receiver or the TV speaker.
 Check the setting of Audio for HDMI in 
the VIDEO menu (page 42).
 Check the HDMI connection (page 20).
 You cannot listen to the Super Audio CD 
by connecting HDMI.
 Depending on the playback component, 
you may need to set up the component. 
Refer to the operating instructions 
supplied with each component.
The source image input to the HDMI 
jack on the receiver is not output from 
the TV.
 Check the HDMI connection (page 20).
 Depending on the playback component, 
you may need to set up the component. 
Refer to the operating instructions 
supplied with each component.
 
						

							69GB
 
 
 
 
 
 
 
 
Additional Information
The control for HDMI function does not 
work.
 Check the HDMI connection (page 20).
 Make sure “CONTROL FOR HDMI” is 
set to “CTRL ON” in VIDEO menu. 
 Make sure the connected component is 
compatible with the Control for HDMI 
function.
 Check the Control for HDMI settings on 
the connected component. Refer to the 
operating instructions of the connected 
component.
 Repeat the procedures of “Preparing 
Control for HDMI function” if you change 
the HDMI connection, connect/disconnect 
the AC power cord, or there is a power 
failure (page 56).
No sound is output from the receiver 
and TV speaker while using the System 
Audio Control function.
 Make sure the TV is compatible with the 
System Audio Control function.
 If the TV does not have System Audio 
Control function, set the “AUDIO FOR 
HDMI” settings in VIDEO menu to
– “TV+AMP” if you want to listen to the 
sound from the TV speaker and 
receiver.
– “AMP” if you want to listen to the 
sound from the receiver.
 If you cannot listen to the sound of a 
component connected to the receiver
– Select the appropriate input when you 
want to watch a program on a 
component connected via HDMI 
connection to the receiver.
– Change the TV channel when you want 
to watch a TV broadcast.
– Select the component or input you want 
to watch when you watch a program on 
the component connected to the TV. 
Refer to the operating instructions of the 
TV on this operation.
Tu n e r
The FM reception is poor.
 Use a 75-ohm coaxial cable (not supplied) 
to connect the receiver to an outdoor FM 
antenna as shown below. If you connect 
the receiver to an outdoor antenna, ground 
it against lightning. To prevent a gas 
explosion, do not connect the ground wire 
to a gas pipe.
Radio stations cannot be tuned in.
 Check that the antennas are connected 
securely. Adjust the antennas and connect 
an external antenna, if necessary.
 The signal strength of the stations is too 
weak (when tuning in with automatic 
tuning). Use direct tuning (page 50).
 Make sure you set the tuning interval 
correctly (when tuning in AM stations 
with direct tuning).
 No stations have been preset or the preset 
stations have been cleared (when tuning 
by scanning preset stations). Preset the 
stations (page 50).
RDS does not work.a)
 Make sure that you are tuned to an FM 
RDS station.
 Select a stronger FM station.
ANTENNA
AM
Receiver
To groundGround wire 
(not supplied)  Outdoor FM antenna 
continued
 
						

							70GB
The RDS information that you want 
does not appear.a)
 Contact the radio station and find out 
whether they actually provide the service 
in question. If so, the service may be 
temporarily out of order.
a)Models of area code CEL, CEK only.
Remote control
The remote does not function.
 For receiver operation, you can only use 
the DISPLAY button when the TUNER 
input is selected.
 Point the remote at the remote sensor on 
the receiver.
 Remove any obstacles in the path between 
the remote and the receiver.
 Replace all the batteries in the remote with 
new ones, if they are weak.
 Make sure you select the correct input on 
the remote.
Error messages
If there is a malfunction, the display shows a 
message. You can check the condition of the 
system by the message. Refer to the following 
table to solve the problem. If any problem 
persists, consult your nearest Sony dealer.
If an error message appears while you perform 
Auto Calibration, see “When error codes 
appear” (page 28) to solve the problem.
PROTECT
Irregular current is output from the 
speakers. The receiver will automatically 
turn off after a few seconds. Check the 
speaker connection and turn on the power 
again.
If you are unable to remedy the 
problem using the 
troubleshooting guide
Clearing the receiver’s memory may remedy 
the problem (page 25). However, note that all 
memorized settings will be reset to their 
factory settings and you will have to readjust 
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if 
service personnel changes some parts during 
repair, these parts may be retained.
Reference sections for clearing 
the receiver’s memory
To clear See
All memorized settings page 25
Customized sound fields page 48