Sony F5 Manual

Operating Clips With a Computer61
External Devices Connection
To use the ExpressCard slot of a 
computer
If the computer is equipped with an ExpressCard/
34 or ExpressCard/54 slot, you can directly insert 
the SxS memory card containing clips recorded 
with this camcorder and access the files.
Notes
 The SxS Device Driver Software must be installed on 
your computer.
 Operation is not guaranteed with all computers.
For support information for the driver, visit the 
following URL:...

External Synchronization62
External Devices Connection
When multiple units of the camcorder are used in 
the same shooting location, synchronized 
recording can be made with a specific reference 
signal, and the timecode can be matched among 
all the units.
Aligning the phase of the video signal 
(Genlock)
Genlock operation is enabled by supplying a 
reference signal to the GENLOCK IN connector 
(page 13) of the camcorder.
Valid reference signals depend on the system 
frequency setting.
You can check the...

Important Notes on Operation63
Appendices
Use and Storage
Do not subject the unit to severe shock
The internal mechanism may be damaged or the 
body warped.
Do not cover the unit while operating
Putting a cloth, for example, over the unit can 
cause excessive internal heat build-up.
After use
Always set the power switch to OFF.
Before storing the unit for a long period
Remove the battery pack.
Do not leave the camcorder with the lenses 
facing the sun
Direct sunlight can enter through the lenses, be...

Important Notes on Operation64
Appendices
About the LCD monitor
 Do not leave the LCD monitor facing direct 
sunlight, as this may damage the LCD monitor.
 Do not press/swipe the LCD monitor forcefully, 
or leave objects on the LCD monitor, as it may 
cause a malfunction, such as picture 
irregularity, etc.
 The LCD monitor may become warm in use. 
This is not a malfunction.
About the stuck pixels
The LCD panel fitted to this unit is manufactured 
with high precision technology, giving a 
functioning...

Formats and Limitations of Outputs65
Appendices
Output formats for the SDI OUT connector
Serial digital signals from the SDI OUT connector are output depending on the settings of the setup menu 
and format of the clip being played.
When outputting one type of SDI output by using the SDI OUT 1 to 4 connectors (PMW-F55 only)
When outputting two types of SDI output by using the SDI OUT 1, 2 (MAIN) and SDI OUT 3, 4 (SUB) 
connectors
Formats and Limitations of Outputs
Video Formats and Output Signals
The...

Formats and Limitations of Outputs66
Appendices
Output formats from the HDMI OUT connector
Serial digital signals from the HDMI OUT connector are output depending on the settings of the setup 
menu and format of the clip being played.
When the output format of SDI (Main) is 4096 × 2160 (PMW-F55 only)
1)Performs conversion from 17:9 to 16:9 (select “Letter Box (H-Fit)” or “Edge Crop (V-Fit).”
When the output format of SDI (Main) is less than 2048 × 1080
The “Frequency” 
setting in “System 
Setting” of the...

Formats and Limitations of Outputs67
Appendices
Output formats from the TEST OUT connector
Signals output from the TEST OUT connector are either the HD-Y or HD SYNC signals output from the 
SDI OUT connector/HDMI OUT connector.
The output signal differs depending on the setting of setup menu or output format setting of SDI (Main)/
SDI (Sub).
The “Frequency” 
setting in “System 
Setting” of the System 
menu
Output format of SDI 
(Main)Output format of SDI 
(Sub)Output format 
59.94 4096 × 2160 59.94P...

Error/Warning Indications68
Appendices
The camcorder informs you of situations where warning, caution, or an operation check is required, 
through messages on the LCD monitor/viewfinder screen, the REC lamp, and a buzzer.
The buzzer is output to the built-in speaker or to the headphones connected via the headphone connector.
The camcorder stops operation after the following indications.
When one of the following indications is generated, follow the message to resolve the problem.
Error/Warning...

Error/Warning Indications69
Appendices
Unknown Media(A)1)
Please ChangeA partitioned memory card or one that contains recorded clips 
exceeding the number permitted with this camcorder is loaded.
This card cannot be used with this camcorder. Remove it and 
load a compatible card.
Media Error
Media(A)
1) Needs to be 
RestoredAn error occurred with the memory card. The card requires 
restoration.
Remove the card, load it again, and restore it.
Media Error
Cannot Record to 
Media(A)
1)
Recording cannot be...

Error/Warning Indications70
Appendices
1)“Media(B)” for the card in slot B, “AXS Memory” for the AXS memory card. Copy Error! 
(CANCEL:Abort)
Cannot Use Media(A)
1)
A memory card that cannot be used with the camcorder is 
inserted.
Replace the card in the respective slot.
Cannot Use Media(A)
1)
Unsupported File SystemA memory card with different file system is inserted.
Replace the card, format it with the camcorder.
Warning indication 
on LCD/viewfinderBuzzerREC 
lampCause and measures