Sony F 35 User Manual

11Example of System Configuration
  Chapter 1   Overview
1-2-1 SRW-1 Docking System
An SRW-1 recorder can be mounted either on the top or rear of the camera head.
Power can also be supplied to the recorder via the DC IN connector (LEMO 8-pin) of the camera head.
Upper docking
The interface box can be attached to the rear.Rear docking
The interface box can be attached to the top.
1-2-2 Optical Fiber System Using the CA-F101
Attaching an optional CA-F101 Optical Fiber Camera 
Adapter to the camera enables...

12Locations and Functions of Parts
  Chapter 1   Overview
1-3 Locations and Functions of Parts
1-3-1 Camera Head
Front panel
aVF1 (viewfinder 1) connector (20-pin)
Connect a viewfinder (optional).
bCONTROL PANEL connector
Connect with the CAMERA connector of the supplied 
assistant panel (page 17).
cAccessory receptacles
Using these screw holes in combination with the accessory 
pockets (page 13) on the left side, you can fix a certain 
accessory to the left side of the camera.
dVF2 (viewfinder 2)...

13Locations and Functions of Parts
  Chapter 1   Overview
Left panel
aLevel vial
Used as a reference to check that the camera stands 
horizontally. It can be fine-adjusted when required.
If fine-adjustment is required, remove the cover and adjust 
it by rotating the three slotted-head screws. 
bL handle
The L handle is attached to the top of the camera head at 
the factory.
It has three screw holes (
3/8) for accessories on the upper 
side. The assistant panel (page 17) can be mounted on the 
outside of...

14Locations and Functions of Parts
  Chapter 1   Overview
h (network) connector (RJ-45 type, 10BASE-T, 
100BASE-TX)
For control from the MSU-900/950 Master Setup Unit, etc. 
via a network cable. 
The necessary settings are made using the NETWORK 
menu displayed on the viewfinder or monitor screen.
For safety, do not connect the connector for peripheral 
device wiring that might have excessive voltage to this 
port. Follow the instructions for this port.
Par mesure de sécurité, ne raccordez pas le...

15Locations and Functions of Parts
  Chapter 1   Overview
The firmware of the SRW-1 may be required to be updated 
for use with this camera. For details, consult your local 
Sony representative.
dAssignable 4/AUTO BLK BAL (auto black balance) 
switch
Push the switch downward to the AUTO BLK BAL side to 
start the auto black balance adjustment.
The function activated by pressing the switch upward to 
the 4 side can be selected using the subdisplay on the left 
panel or on the assistant panel or the menu...

16Locations and Functions of Parts
  Chapter 1   Overview
fMENU SEL (selection) /ENTER dial
Used to select or set the items on the subdisplay or the 
menu items on the viewfinder (monitor) screen.
Rear panel
aSafety release tab
bAccessory clamp lever
cLock release knob
dAccessory mount lever
For mounting/unmounting an SRW-1 HD Portable Digital 
Recorder or the interface box to/from the rear of the 
camera head. 
The mounting/unmounting mechanism is the same as that 
on the top (page 15).
For details, see...

17Locations and Functions of Parts
  Chapter 1   Overview
1-3-2 Assistant Panel (Supplied)
The most parts are common to those on the right panel of 
the camera head. Connecting the panel to the CONTROL 
PANEL connector (page 12) of the camera head permits 
the camera and recorder to be operated at hand.
aCAMERA connector
Using the supplied assistant panel cable, connect to the 
CONTROL PANEL connector of the camera head.
bAUX (auxiliary) connector
Connect to an external device as required.
The other...

18Locations and Functions of Parts
  Chapter 1   Overview
eCamera connector 1
When the interface box is mounted on the top or rear of the 
camera head, video/audio and control signals are sent/
received to/from the camera head.
fCamera connector 2
When the interface box is mounted on rear of the camera 
head, power is sent/received to/from the camera head. 

19
  Chapter 2   Installation and Preparations
Chapter
Mounting the Interface Box
2
Installation and 
Preparations
2-1 Mounting the 
Interface Box
The supplied interface box can be attached to the top or 
rear of the camera head.
Connection between the camera head and the interface box 
is achieved by mounting, eliminating additional cable 
connections.
 The same attaching/detaching system is used both on the 
top and the rear.
 The following instructions use the illustrations of 
attaching the interface...

20Mounting the Interface Box
  Chapter 2   Installation and Preparations
5Rotate the accessory mount lever downward (pull it in 
the opposite direction of the lens when attaching to the 
top).
6While holding the lock-release knob in the direction of 
the arrow, fold the accessory mount lever into its home 
position.
7Rotate the accessory clamp lever downward (toward 
the opposite direction of the lens when attaching to the 
top).
To detach
1Rotate the accessory clamp lever upward (toward the 
lens when...