Sony Dav Sr3 Operating Instructions

Getting Started
11GB
Check that you have the following items:
Speakers (5)
 Subwoofer (1)
 AM loop antenna (aerial) (1)
 FM wire antenna (aerial) (1)
 Speaker cords (3.5m × 3, 10m × 2) 
 Remote Commander (remote) RM-SP320 (1)
 Size AAA (R03) batteries (2)
 Foot pads (8)
 Operating Instructions
 Speakers - Connection and Installation (card) 
(1)You can control the system using the supplied 
remote. Insert two size AAA (R03) batteries by 
matching the 3 and # ends on the batteries to 
the...

12GB
Connect the supplied speaker system using the supplied speaker cords by matching the colors of the 
jacks to those of the cords. Do not connect any speakers other than those supplied with this system.
To obtain the best possible surround sound, specify the speaker parameters (distance, level, etc.) on 
page 24.
Required cords
Speaker cords
The connector and the color tube of the speaker cords are the same color as the label of the jacks to be 
connected.
To attach the foot pads
To prevent speaker...

Getting Started
13GB
Terminals for connecting the speakers
Connect the To the
Front speakers SPEAKER FRONT L (white) and R (red) jacks
Surround speakers SPEAKER SURR L (blue) and R (gray) jacks
Center speaker SPEAKER CENTER (green) jack
Subwoofer SPEAKER WOOFER (purple) jacks
AUDIO IN
VIDEO
SURROUND
BACK
SAT SPEAKERAUDIO IN
RL
RLCENTERFRONT LFRONT R
SURR L
WOOFER
WOOFERSURR R
EURO AV OUTPUT(TO TV)
Front speaker (R)
Center speakerFront speaker (L)
Surround speaker (R)
SubwooferSurround speaker (L)...

14GB
Notes on placing speakers
 Do not set the speakers in an inclined position.
 Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
 Use caution when placing the subwoofer, tall speakers, or speaker stands (not supplied) that are attached with the 
surround speakers on a specially treated (waxed, oiled, polished, etc.) floor, as staining or discoloration may result.
Notes on placing front...

Getting Started
15GB
Note for connecting the speaker cords to the system
Connect the stripped ends of the cords to the terminals, taking care to avoid contact between the cords. 
Make sure the cords are firmly connected to the speaker and speaker terminals.
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these 
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch 
another...

16GB
To change the speaker cables
If you want to use a different speaker cable, you can detach the plug for attachment to another cable.
Detaching 
With the catcher facing down, press and hold the plug down against a flat surface and remove the cords 
from plug.
Attaching
While pressing the plug down against a flat surface, insert the new speaker cords. 
Note that the cord marked with a line should be attached to the minus (-) side of the plug. 
Notes
 Be careful not to damage the surface you use (desk,...

Getting Started
17GB
Connect the supplied AM/FM antennas (aerials) for listening to the radio.
Terminals for connecting the antennas (aerials)
Notes
 To prevent noise pickup, keep the AM loop antenna (aerial) away from the system and other components.
 Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
When you connect the supplied AM loop antenna (aerial), the cord (A) and the cord (B) can be connected in either...

18GB
Tip
If you have poor FM reception, use a 75-ohms coaxial cable (not supplied) to connect the system to an outdoor 
FM antenna (aerial) as shown below.
COAXIAL
AMFM 75
Outdoor FM 
antenna (aerial)
System
 

Getting Started
19GB
Required cords
SCART (EURO AV) cord for connecting a TV (not supplied)
Audio cords (not supplied) 
When connecting a cord, be sure to match the color-coded sleeves to the appropriate jacks on the 
components.
Terminals for connecting video components
Connecting the system to a TV
Connect the system to your TV using the SCART (EURO AV) cord. Be sure to connect the SCART 
(EURO AV) cord to the T EURO AV OUTPUT (TO TV) jack on the system.
When you connect using the SCART (EURO AV) cord,...

20GB
Notes
 Make connections securely to prevent unwanted noise.
 Refer to the instructions supplied with the TV.
 The system cannot output component video signals.
 The system cannot output an audio signal to the connected TV. Only the audio signal of the TV is output from the 
system speakers.
Tips
 When you want to output the TV sound or stereo sound of a 2 channel source from the 6 speakers, select any sound 
field other than “AUTO FORMAT DIRECT AUTO” or “2CH STEREO” (page 46).
 If a distortion...