Sony Dav Sr2 Operating Instructions

Other Operations
61GB
By adjusting the remote signal, you can control 
your TV with the supplied remote.
Notes
 If you enter a new code number, the code number 
previously entered will be erased.
 When you replace the batteries of the remote, the 
code number may reset itself to the default (SONY) 
setting. Reset the appropriate code number.
Controlling TVs with the 
remote
Press and hold TV [/1 while entering your 
TV’s manufacturer’s code (see the table) 
using the number buttons. Then release TV...

62GB
Kiton 027
KTV 002, 020
LG/Goldstar 002, 020, 027, 028, 038
LOEWE 027, 028, 038
LXI(Sears) 002, 009, 012, 034, 046
MAGNAVOX 002, 020, 027, 034
MARANTZ 022
Mark 027
Matsui 010, 052, 053
Medion 027
Mitsubishi/MGA 002, 021, 022
NEC 002, 020, 023, 024, 048
NEI 027
NOKIA 025, 026
Nokia Oceanic 026
Nordmende 035, 042
Okano 027
ORION 007
PANASONIC 049, 050, 051
Philco 002, 004, 015, 020, 034
PHILIPS 013, 027, 034
Phoenix 027
PIONEER 029, 030, 031, 046, 049
Portland 002
Provision 027
PYE 027
QUASAR 039, 049...

Other Operations
63GB
Controlling the TV
You can control your TV using the buttons 
below.
Using the number buttons for 
controlling the TV
When you set the remote to the TV mode, you 
can use the number buttons for controlling the 
TV.
Press the TV button.
The TV button turns red and the remote is set to 
the TV mode. You can select the TV channels by 
using the number buttons.
>10 is for selecting the channel number greater 
than 10.
To cancel the TV mode, press the TV button 
again.
Notes
 Depending...

64GB
* Except for North American models.
Operation
Point the remote to the direction of TV and this 
system, then press SONY TV DIRECT once.
While transmitting the code from the remote, the 
TV button flashes.
If this function does not work, change the 
transmit time. The transmit time varies 
depending on the TV.
To change the transmit time
Press and hold TV CH + while entering the 
code for transmit time (see table below) using 
the number buttons.
The transmit time from the remote is selected.
If you...

Other Operations
65GB
You can use VCRs or other units connected to 
the VIDEO or SAT jacks. Refer to the operation 
manual supplied with the unit for further 
information on the operation.
Press FUNCTION repeatedly until VIDEO or 
SAT that you connected the unit to appears 
in the front panel display.
Each time you press FUNCTION, the mode of 
the system changes in the following sequence.
FM t AM t VIDEO t SAT t DVD t 
FM...You can enjoy multiplex broadcast sound when 
the system receive the AC-3...

66GB
xSUB
Sub sound is output from the left and right 
speakers.
xMAIN+SUB
Main sound and Sub sound are output from 
the left and right speakers.
xMAIN/SUB
Main sound is output from the left speaker 
and Sub sound is output from the right 
speaker.
5Press AMP MENU.
Turns off the AMP menu.
Presetting Radio Stations
You can preset 20 FM stations, and 10 AM 
stations. Before tuning, make sure to turn down 
the volume to minimum.
1Press TUNER/BAND repeatedly until 
the band you want appears in the front...

Other Operations
67GB
5Press ENTER.
A preset number appears in the front panel 
display.
6Press C/c/x/X to select/ the preset 
number you want.
7Press ENTER.
The station is stored.
8Repeat 1 to 7 to store other stations.
To change the preset number
Restart from step 1.
To change the AM tuning interval 
The AM tuning interval can be set to either 
10 kHz (default) or 9 kHz (for some areas).
To change the AM tuning interval, first tune in 
any AM station, then turn off the system by 
pressing "/1 on...

68GB
To listen to non-preset radio 
stations
Use manual or automatic tuning in Step 2. 
For manual tuning, press TUNING + or – on the 
remote repeatedly.
For automatic tuning, press and hold TUNING + 
or – on the remote. Press x when you stop the 
automatic tuning. 
Tips
 If an FM program is noisy, press FM MODE on the 
remote so that “MONO” appears in the front panel 
display. There will be no stereo effect, but the 
reception will improve. Press the button again to 
restore the stereo effect.
 To...

Other Operations
69GB
6Create an index name by using the 
cursor buttons:
Press X/x to select a character, then press c 
to move the cursor to the next position.
If you make a mistake
Press C/c repeatedly until the character to 
be changed flashes, then press X/x to select 
the desired character. Capital letters, 
numbers, and other symbols can be input 
for a radio station name.
7Press ENTER.
The station name is stored.You can set the system to turn off at a preset 
time, so you can fall asleep...

70GB
You can change the brightness of the front panel 
display by two steps.
1Press AMP MENU.
2Press x/X repeatedly until “CUSTOMIZE” appears in the front 
panel display, then press ENTER or c.
The system enters the Customize Menu 
mode.
3Press x/X repeatedly until “DIMMER” 
appears in the front panel display, then 
press ENTER or c.
4Press x/X to select the brightness of 
the front panel display.
5Press AMP MENU.
Turns off the AMP menu.You can return the system parameters such as 
speaker settings and...