Sony Dav Fx999w Operating Instructions

Getting Started
31GB
– your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (MONITOR 
OUT (VIDEO/S VIDEO)).
About DVD software types and the conversion method
DVD software can be divided into 2 types: film-based software and video-based software. 
Video-based software is derived from TV, such as dramas and sit-coms, and displays images at 30 
frames/60 fields per second. Film-based software is derived from film and displays images at 24 frames 
per second. Some DVD software contains...

32GB
DAV-FX1000W
To connect the AUDIO OUT jacks of a TV to the SAT (AUDIO IN) jacks 
of this system
Connect a TV to the SAT (AUDIO IN) jacks using an audio cord (not supplied). When connecting a 
cord, be sure to match the color-coded sleeves to the appropriate jacks on the components.
 Be sure to make connections securely to avoid hum and noise.
 If your TV does not have AUDIO OUT jacks, you cannot output the TV sound from the speakers of this system.
 To listen to the TV sound, select the function...

Getting Started
33GB
To reset to NTSC, turn off the system and then turn on again by pressing "/1 while pressing and 
holding X on the system.
If the color system of the TV is NTSC
Do the same operation above to set the system to NTSC from PAL.
 

34GB
 
You can enjoy other component by connecting the VIDEO/AUDIO OUT jacks of another component.
Connecting the system and the other component
Outputs the other component through the speakers of this system.
DAV-FX999W
Step 4: Other Component Hookup
RAUDIO
OUT
L
VIDEO
OUT
RAUDIO
OUT
L
VIDEO
OUTOPTICAL 
DIGITAL
OUT
AUDIO IN
RL
RL
AUDIO INVIDEO IN
VIDEO IN
COAXIAL
AM
FM75SPEAKERSAT DIR-T1COMPONENT VIDEO  OUTMONITOR OUTDIGITAL IN OPTICAL
(DVD ONLY)
VIDEO
(DVD ONLY)S VIDEOYPB/CBPR/CR
FRONT R FRONT L CENTER...

Getting Started
35GB
DAV-FX1000W
To connect the VIDEO/AUDIO OUT jacks of other component to the 
VIDEO or SAT (VIDEO/AUDIO IN) jacks of this system
Connect the VCR or other components to the VIDEO or SAT (VIDEO/AUDIO IN) jacks using the 
video/audio cord (not supplied). When connecting a cord, be sure to match the color-coded sleeves to 
the appropriate jacks on the components.
If you connect a digital satellite receiver with an DIGITAL OUT 
(OPTICAL) jack
The digital satellite receiver can be connected...

36GB
Before connecting the AC power cord (mains 
lead) of this system to a wall outlet (mains), 
connect the speakers to the system (page 15).
To turn on the system
Press "/1.
To turn off the system
Press "/1. The system enters standby mode.
While playing a disc, do not turn off the system 
by pressing "/1. Doing so may cancel the menu 
settings. When you turn off the system, first 
press x to stop playback and then press "/1.After connecting the AC power cord (mains 
lead), the...

Getting Started
37GB
After connecting the speakers, surround 
amplifier, IR transmitter, IR receiver, and the 
AC power cords (mains leads), adjust the 
wireless system for good transmission.
1Press "/1 on the system and POWER 
on the surround amplifier.
The system and surround amplifier turn on 
and the POWER/ON LINE indicator turns 
red.
2Orient the IR transmitter and IR 
receiver to face each other.
Adjust the position until the POWER/ON 
LINE indicator turns green.
 The IR transmitter is movable...

38GB
To hang the IR receiver on a wall
1Install a commercially available screw 
in the wall so that it protrudes 4 mm.
2Detach the IR receiver stand and hang 
it via hole on the rear side of the IR 
receiver on the screw.
Make sure that the IR receiver does not 
move after installation.
 When reattaching the IR receiver stand to the IR 
receiver, attach the stand so that both delta marks on 
the IR receiver and stand are aligned (page 16). 
To hang the IR transmitter on a 
wall
1Rotate the stand of the...

Getting Started
39GB
 Use screws suitable for the material and strength of 
the wall.
 Do not install the IR transmitter or IR receiver to a 
wall of low strength.
 Sony is not liable for any damage or accident incurred 
by incorrect installation (i.e. low strength wall, etc.), 
incorrect use of this product, or natural disaster.
 When connecting/disconnecting cords, detach the IR 
transmitter or IR receiver from the wall first.
Follow the steps below to make the minimum 
number of basic adjustments...

40GB
The Setup Display for selecting the 
language used in the on-screen display 
appears.
5Press X/x to select a language.
The system displays the menu and subtitles 
in the selected language.
 The selectable language is different depending 
on the area. 
6Press ENTER.
The Setup Display for selecting the aspect 
ratio of the TV to be connected appears.
7Press X/x to select the setting that 
matches your TV type.
xIf you have a 4:3 standard TV
[4:3 LETTER BOX] or [4:3 PAN SCAN] 
(page 92)
xIf you have a...