Sony Dav Dz720k Operating Instructions
Here you can view all the pages of manual Sony Dav Dz720k Operating Instructions. The Sony manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 11
11GB Getting Started – BASIC – 5Slide the speaker down slowly onto the pedestal. Note Do not catch the speaker cord between the speaker and the pedestal. Do not drop the speaker when mounting. 6Secure the speaker with the screws in order 1 to 2. Adjust the length of the speaker cord. Screws (2) (supplied)1 2
Page 12
12GB Getting Started – BASIC – This hookup is the basic connection of the system to the speakers and TV. For other TV connections, see page 21. For other component connection, see page 25. To accept progressive signals, see page 23. To change the color system (PAL or NTSC), see page 15. Refer to the connection diagram below, and read the additional information from 1 to 4 on the following pages. Step 2: Connecting the System and TV RAUDIO OUT L VIDEO IN COAXIAL AM FM75 SPEAKER FRONT R FRONT L SUR R...
Page 13
13GB Getting Started – BASIC – 1 Connecting the Speakers Required cords The connector and color tube of the speaker cords are the same color as the label of the jacks to be connected. Note Do not catch the speaker cord insulation in the SPEAKER jack. To avoid short-circuiting the speakers Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch another speaker...
Page 14
14GB Getting Started – BASIC – Tip When you want to output the TV sound or stereo sound of a 2 channel source from the 6 speakers, select the “Dolby Pro Logic,” “Dolby Pro Logic II MOVIE,” or “Dolby Pro Logic II MUSIC” sound field (page 30). 3 Connecting the Antenna (Aerial) To connect the AM antenna (aerial) The shape and the length of the antenna (aerial) is designed to receive AM signals. Do not dismantle or roll up the antenna (aerial). 1Remove only the loop part from the plastic stand. 2Set up...
Page 15
15GB Getting Started – BASIC – To connect the FM wire antenna (aerial) Connect the FM wire antenna (aerial) to the COAXIAL FM 75 Ω jack. Note Be sure to fully extend the FM wire antenna (aerial). After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the system to an outdoor FM antenna (aerial) as shown below. 4 Connecting the AC power cord (mains lead) Before connecting the AC power...
Page 16
16GB Getting Started – BASIC – Positioning the speakers For the best possible surround sound, all the speakers other than the subwoofer should be the same distance from the listening position (A). However, this system allows you to place the center speaker up to 1.6 meters (5 ft) closer (B) and the surround speakers up to 5.0 meters (16 ft) closer (C) to the listening position. The front speakers can be placed from 1.0 to 7.0 meters (3 to 23 ft) (A) from the listening position. Place speakers as...
Page 17
17GB Getting Started – BASIC – Follow the steps below to make the minimum number of basic adjustments for using the system. 1Turn on the TV. 2Press [/1. Note Disconnect the headphones when you perform the Quick Setup. You cannot operate steps after 10 with the headphones connected. Make sure that the function is set to “DVD.” 3Switch the input selector on your TV so that the signal from the system appears on the TV screen. [Press [ENTER] to run QUICK SETUP.] appears at the bottom of the screen....
Page 18
18GB Getting Started – BASIC – 10Connect the calibration mic to the A.CAL MIC jack on the front panel and press X/x to select [YES], then press . Set up the calibration mic at the ear level using a tripod, etc. (not supplied). The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. Be quiet during the measurement. Auto Calibration starts. Note Loud test sound is output when [AUTO CALIBRATION] starts. You cannot...
Page 19
Getting Started – ADVANCED – 19GB After connecting the AC power cord (mains lead), the demonstration appears in the front panel display. When you press "/1 on the remote, the demonstration turns off. Note When you press "/1 on the system, the demonstration does not turn off. When you set the demonstration mode in the AMP menu to on, the demonstration does not turn off even though you press "/1 on the remote. To turn off the demonstration, set the demonstration mode to off, then...
Page 20
20GB 1Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. See the illustrations below. 2Fasten the screws to the wall. For the center speaker For the other speakers 3Hang the speakers on the screws. Note Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied....