Sony Dav Dz340m Operating Instructions

21GB
Getting StartedCaution
 Contact a screw shop or installer for information regarding the wall material or screws to be used.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam. Install the speakers on a vertical and flat wall where reinforcement is applied.
 Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or 
improper screw installation,...

22GB
Getting Started
2Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. 
See the illustrations below.
3Fasten the screws to the wall, then hang the speaker on the wall.
30 mm 4 mm 
Hole on the back of 
the speaker
5 mm
10 mm
8 mm to 10 mm
Depth of fastened screw
145 mm For the center speakerFor the tall speakers (DAV-DZ640K/DAV-
DZ840K/DAV-DZ940K only)
For the small speakers (DAV-DZ340K/
DAV-DZ640K only)
400 mm
 

23GB
Getting Started
To install the front speakers on a wall using the wall mounting parts
(Indian models of DAV-DZ340K only)
1Pass the speaker cord through the mounting plate, then attach the mounting plate to the 
wall using commercially available screws.
Use the speaker cords as follows:
 Front left speaker (L): White
 Front right speaker (R): Red
2Remove the cover from the mounting bracket, pass the speaker cord through the hole 
on the rear side of the mounting bracket and out from the front side of...

24GB
Getting Started
3Tightly secure the speaker to the mounting bracket with the screw (supplied).
4Adjust the length of the speaker cord as you bring the shaft knob together with the 
mounting plate, then insert the knob firmly until it stops.
5After deciding the angle, secure a screw on the lower side (1), then secure a screw on 
the upper side (2).
Note Make sure that the wall is sufficiently thick before installing.
 Do not loosen the screws at the mounting plate or screw to secure the speaker to...

25GB
Getting StartedStep 2: Connecting the System
1Connect the speaker cord with the color tube to 3, and the speaker cord without the 
color tube to #.
The subwoofer speaker cord is fixed to the subwoofer.
Note Do not catch the speaker cord insulation (rubber covering) in the speaker terminals.
2Insert the connectors of the speaker cords to match the color of the SPEAKERS jacks 
of the unit until they click.
Connecting the speakers
Color tube
(–) (+)Rear of the speaker
Connector
SPEAKERSS
U
R
 RS
U
R...

26GB
Getting Started
1 Connecting the video to your TV
Depending on the jacks on your TV, select one of the connection methods.
xMethod 1: Video cord (supplied) connection
This is the basic connection.
xMethod 2: HDMI cable* connection
Picture quality will be improved compared to Method 1.
If your TV is compatible with the Audio Return Channel function, this connection also sends a digital 
audio signal from the TV. You do not need to make a separate audio connection for listening to TV 
sound. For...

27GB
Getting Started
* The High Speed HDMI cable is supplied with certain models/in certain areas only.
VIDEO IN
COMPONENT VIDEO INPB/CBPR/CRYHDMI IN
COMPONENT VIDEO OUTVIDEO OUTPBYPR
OUTARC
Method 2*Method 3 
(not supplied)Method 1 
(supplied)
 

28GB
Getting Started
2 Connecting the audio from your TV/set-top box
To listen to TV or set-top box sound via the system, select one of the connection methods.
xMethod 1: Audio cord (not supplied) connection
This is the basic connection and sends an analog audio signal.
xMethod 2: Digital optical cord (not supplied) connection (DAV-DZ840K/DAV-DZ940K only)
Sound quality will be improved compared to Method 1.
Note The TV (DIGITAL IN OPTICAL) jack is available on DAV-DZ840K/DAV-DZ940K only.
 The system can...

29GB
Getting Started
To change the color system (PAL or NTSC) (African, Asian, Indian, and 
Middle Eastern models only)
Depending on your TV, you may be required to select either PAL or NTSC for the color system.
The initial setting for African, Indian, and Middle Eastern models is PAL.
The initial setting for Asian models is NTSC.
1Turn off the system by pressing "/1.
2Turn on the system by pressing "/1 on the unit while pressing FUNCTION on the unit.
Each time you perform this operation, the...

30GB
Getting Started
Note After connecting the FM wire antenna (aerial), extend and keep it as horizontal as possible.
1Connect the AC power cord (mains lead).
The demonstration appears in the front panel display.
2Press "/1 on the remote to turn the system on, then press "/1 again to turn off the 
demonstration.
Connecting the antenna (aerial)
Connecting the AC power cord (mains lead)
ANTENNAC
O
A
X
IA
L
  7
5
F
M
or
FM wire antenna (aerial)
(supplied)
Wall outlet (mains): The shape of 
the wall...