Sony Bdv E801 Operating Instructions

							External Audio Device
61GB
To set the ID of the surround 
amplifier
Refer to the operating instructions of the 
surround amplifier.
To set the ID of the S-AIR 
receiver
Refer to the operating instructions of the S-AIR 
receiver.
To use multiple S-AIR main units
You can use multiple S-AIR main units by 
setting a different ID for each component.You can enjoy the system’s sound by using the 
S-AIR receiver. The S-AIR receiver can be 
placed in another room for enjoying the 
system’s sound there.
For details of the S-AIR receiver, refer to the 
operating instructions of the S-AIR receiver.
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “S-AIR 
MODE” appears in the front panel 
display, then press   or c.
Note When the wireless transmitter is not inserted in 
the unit, “S-AIR MODE” cannot be selected.
4Press X/x to select the desired setting.
: The S-AIR receiver outputs 
sound according to functions set on the 
unit.
 “SEPARATE”: You can set the desired 
function for the S-AIR receiver while unit 
functions do not change.
5Press .
The setting is made.
6Press SYSTEM MENU.
The system menu turns off.
ID A S-AIR main unit
(This unit)
ID A
S-AIR sub unitID A
S-AIR sub unit
Other S-AIR 
main unit S-AIR main unit
(This unit)
ID A
S-AIR sub unitID A
S-AIR 
sub unitID B
S-AIR sub unit ID AID B
Enjoying the system’s sound in 
another room
For the S-AIR receiver
 
						

							62GB
7Select the desired function on the 
S-AIR receiver.
xWhen “PARTY” is set
The S-AIR receiver’s function changes 
sequentially as you press FUNCTION of 
the main unit (page 34) or S-AIR CH of the 
S-AIR receiver.
xWhen “SEPARATE” is set
The S-AIR receiver’s function changes 
by pressing S-AIR CH of the S-AIR 
receiver as follows.
“MAIN UNIT” t “TUNER FM” t 
“DMPORT” t “AUDIO” t …
To enjoy the same function as the unit, 
select “MAIN UNIT.”
8Adjust the volume on the S-AIR 
receiver.
Note When the sound is other than 2 channel stereo, multi-
channel sound is downmixed to 2 channel.
 The sound of the S-AIR receiver may be cut off by 
operation of the unit.
To control the system from the 
S-AIR receiver
You can control the system from the S-AIR 
receiver by using the following buttons.
For details, refer to the operating instructions of 
the S-AIR receiver.You can enjoy the S-AIR receiver while the unit 
is in standby mode by setting “S-AIR STBY” to 
“STBY ON.”
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “S-AIR 
STBY” appears in the front panel 
display, then press   or c.
Note When the wireless transmitter is not inserted in 
the unit, “S-AIR STBY” cannot be selected.
4Press X/x to select the desired setting.
 “STBY ON”: You can enjoy the S-AIR 
receiver while the unit is in standby mode 
or turned on. The power consumption 
during standby mode increases.

: You cannot enjoy the 
S-AIR receiver while the unit is in 
standby mode.
5Press .
The setting is made.
6Press SYSTEM MENU.
The system menu turns off.
Note When you turn the system off while “S-AIR STBY” 
is set to “STBY ON,” “S-AIR” flashes (when sound 
transmission between the unit and S-AIR receiver is 
not established), or lights up (when sound 
transmission between the unit and S-AIR receiver is 
established) in the front panel display.
Press Operation
N, X, x, 
./>Share the same operations on the 
remote and unit.
S-AIR CH Change the function of the system.
Enjoying the S-AIR receiver 
while the unit is in standby 
mode
For the S-AIR receiver
 
						

							External Audio Device
63GB
It is easy to set the same ID for the unit and an 
S-AIR sub unit, such as a surround amplifier or 
S-AIR receiver, to establish sound transmission. 
However, neighbors may also receive your 
system’s sound if IDs are the same, or you may 
receive sound from neighbors. To prevent this, 
you can identify the unit with a specific S-AIR 
sub unit by performing the pairing operation.
xBefore pairing
Sound transmission is established by the ID 
(example).
xAfter pairing
Sound transmission is established between the 
paired unit and S-AIR sub unit(s) only.
To perform pairing
1Place the S-AIR sub unit that you want 
to pair near the unit.
Note Remove headphones from the surround 
amplifier (if connected).
2Match the IDs of the unit and the S-AIR 
sub unit.
 To set the ID of the unit, see “To set the ID 
of the unit” (page 60).
 To set the ID of the S-AIR sub unit, refer 
to the operating instructions of the S-AIR 
sub unit.
3Press SYSTEM MENU.
4Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
5Press X/x repeatedly until “PAIRING” 
appears in the front panel display, then 
press  or c.
Note When the wireless transmitter is not inserted in 
the unit, “PAIRING” cannot be selected.
Identifying the unit with a 
specific S-AIR sub unit 
(Pairing operation)
For the surround amplifier
For the S-AIR receiver
This unit
ID A
ID A
S-AIR sub unitID A
S-AIR sub unit Your room
Neighbor
This unit
ID A
S-AIR sub unitID A ID A
S-AIR sub unit Your room
Neighbor
PairingNo transmission
 
						

							64GB
6Press X/x repeatedly until “START” 
appears in the front panel display, then 
press .
The unit starts pairing and “SEARCH” 
flashes in the front panel display.
To cancel pairing, press SYSTEM MENU.
7Start pairing of the S-AIR sub unit.
xFor the surround amplifier
Press POWER on the surround amplifier to 
turn on the surround amplifier and press 
PAIRING on the rear panel of the surround 
amplifier.
The PAIRING indicator of the surround 
amplifier flashes red when pairing starts.
When sound transmission is established, 
the PAIRING indicator of the surround 
amplifier turns red and “PAIRING” and 
“COMPLETE” appear alternately in the 
front panel display.
Tip To press PAIRING on the rear panel of the 
surround amplifier, a slim instrument, such as a 
paper clip, can be used.
xFor the S-AIR receiver
Refer to the operating instructions of the 
S-AIR receiver.
When sound transmission is established, 
“PAIRING” and “COMPLETE” appear 
alternately in the front panel display.
Note Perform pairing within several minutes of Step 
5. If you do not, “PAIRING” and 
“INCOMPLETE” appear alternately in the front 
panel display. To continue pairing, press   and 
start again from Step 5. To cancel pairing, press 
SYSTEM MENU.
8Press SYSTEM MENU.
The system menu turns off.
Note When you perform pairing, “(PAIRING)” appears 
beside ID on the display for selecting ID.
To cancel pairing
Change the ID setting of the unit by using the 
S-AIR ID switch of the unit. If you select a new 
ID, pairing is canceled.You can check the S-AIR status such as the 
S-AIR ID or pairing information.
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “S-AIR ID” 
appears in the front panel display, then 
press  or c.
The S-AIR ID of the unit appears in the 
front panel display. When the unit is paired, 
“(PAIRING)” appears beside ID.
4Press SYSTEM MENU.
The system menu turns off.
If you use multiple wireless systems which share 
the 2.4 GHz band, such as wireless LAN or 
Bluetooth, the transmission of S-AIR products 
or other wireless systems may be unstable. In 
this case, the transmission may be improved by 
changing the following “RF CHANGE” setting.
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “RF 
CHANGE” appears in the front panel 
display, then press   or c.
Note When the wireless transmitter is not inserted in 
the unit, “RF CHANGE” cannot be selected.
Checking the S-AIR status of 
the unit
If sound transmission is 
unstable
For the surround amplifier
For the S-AIR receiver
 
						

							External Audio Device
65GB
4Press X/x to select the desired setting.
: Normally select this. The 
system changes “RF CHANGE” to “ON” 
or “OFF” automatically.
 “ON”: The system transmits sound by 
searching for a better channel for 
transmitting.
 “OFF”: The system transmits sound by 
fixing the channel for transmitting.
5Press .
The setting is made.
6Press SYSTEM MENU.
The system menu turns off.
7When you set “RF CHANGE” to “OFF,” 
select the ID so that sound 
transmission is most stable (page 60).
Note In most cases, you will not need to change this 
setting.
– If “RF CHANGE” is set to “OFF,” transmission 
between the unit and S-AIR sub unit can be 
performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE 
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE 
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE 
802.11b/g channel 11
 The transmission may be improved by changing the 
transmission channel (frequency) of the other 
wireless system(s). For details, refer to the operating 
instructions of the other wireless system(s).
 
						

							66GB
Using the Control for 
HDMI Function for 
“BRAVIA” Sync
This function is available on TVs with the 
“BRAVIA” Sync function only.
By connecting Sony components that are 
compatible with the Control for HDMI function 
with an HDMI cable, operation is simplified as 
below:
– Theatre Mode (page 67)
– One-Touch Play (page 67)
– System Power Off (page 67)
– Volume Limit (page 68)
– System Audio Control (page 68)
– Language Follow (page 68)
Control for HDMI is a mutual control function 
standard used by CEC (Consumer Electronics 
Control) for HDMI (High-Definition 
Multimedia Interface).
The Control for HDMI function will not work in 
the following cases:
– When you connect this system to a 
component which is not compatible with the 
Control for HDMI function.
– A component does not have an HDMI jack.
There are convenient buttons on the system’s 
remote for operating the TV, such as 
THEATRE, ONE-TOUCH PLAY, and TV "/1. 
For details, see “Controlling Your TV with the 
Supplied Remote” (page 72) and refer to the 
operating instructions of the TV.
Note Depending on the connected component, the Control 
for HDMI function may not work. Refer to the 
operating instructions supplied with the component.
 The Control for HDMI function may not work if you 
connect a component other than Sony, even if the 
component is compatible with the Control for HDMI 
function.
(Control for HDMI - Easy Setting)
The system is compatible with the Control for 
HDMI - Easy Setting function. If the TV is 
compatible with the Control for HDMI - Easy 
Setting function, you can set the system’s 
[Control for HDMI] function automatically by 
setting the TV. For details, refer to the operating 
instructions of the TV.
If the TV is not compatible with the Control for 
HDMI - Easy Setting function, set the Control 
for HDMI function of the system and TV 
manually.
Note For details on setting the TV, refer to the operating 
instructions.
1Make sure that the system and the TV 
are connected with an HDMI cable.
2Turn on the TV and press [/1 to turn on 
the system.
3Switch the input selector on your TV so 
that the signal from the system through 
the HDMI input appears on the TV 
screen.
4Set the Control for HDMI function of the 
system and TV.
The Control for HDMI function for system 
and TV is simultaneously set to on.
Other Operations
THEATRE
NIGHT
SLEEPDYNAMICBASS
TV
TVONE-TOUCH
PLAY
BRAVIA  Sync
Preparing for the Control for 
HDMI function
 
						

							Other Operations
67GB
To set the [Control for HDMI] 
function of the system to on/off 
manually
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [HDMI Settings], 
then press  .
The options for [HDMI Settings] appear.
4Press X/x to select [Control for HDMI], 
then press  .
5Press X/x to select the setting, then 
press .
: On.
 [Off]: Off.
Note During the setting of the Control for HDMI function 
for the system, the System Audio Control function 
does not work.
Tip The default setting of the Control for HDMI function 
of the system is [On].
(Theatre Mode)
If your TV is compatible with the Theatre mode, 
when you press THEATRE, you can enjoy the 
optimum video mode and sound quality suited 
for movies, and TV sound is output from the 
system’s speakers automatically. Also, the TV’s 
video mode switches to Theatre Mode.(One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV 
turns on, the TV is set for BD/DVD input 
selector, and the system starts playing a disc 
automatically.
Also, when you insert a disc, One-Touch Play is 
enabled. If One-Touch Play does not start (in the 
case of inserting a disc that is not compatible 
with the auto playback function), press N or 
ONE-TOUCH PLAY.
The system and TV work as follows (e.g.):
(System Power Off)
When you turn the TV off by using the POWER 
button on the TV’s remote or TV "/1 on the 
system’s remote, the system turns off 
automatically.
Note Before using the System Power Off function, set the 
function for TV power. For details, refer to the 
operating instructions of the TV.
 Depending on the status, the system or the connected 
components may not turn off automatically. For 
details, see the operating instructions supplied with 
the connected components.
Using the Theatre Mode
Watching BD/DVD by a single 
button press
This system TV
Turns on. (If not already 
turned on.)
r
Switches to “BD/DVD” 
function.
r
Starts playing the disc and 
outputs the sound.Turns on. (If not already 
turned on.)
r
Switches to HDMI input.
r
Minimizes sound level.
(System Audio Control)
Turning the system off in sync 
with the TV
 
						

							68GB
(System Audio Control)
You can enjoy TV sound in this system by easy 
operation.
To use this function, connect the system and the 
TV with an audio cord and an HDMI cable 
(page 22).
You can use the System Audio Control function 
as follows:
 You can enjoy TV sound from the speakers of 
the system by means of a simple operation. For 
details, see the operating instructions of the 
TV.
 When the system is turned on, TV sound will 
be output from the speakers of the system.
 When TV sound is output from the speakers of 
the system, you can adjust the volume and turn 
off the sound of the system using the TV 
remote.
Note While the TV is in PAP (picture and picture) mode, 
the System Audio Control function will not work. 
When the TV exits PAP mode, the output method of 
the TV returns to the one before PAP mode.
(Volume Limit)
If you change the output method of the TV to the 
system speaker on the TV menu or by pressing 
THEATRE, loud sound may be output 
depending on the volume level of the system. 
You can prevent this by limiting the maximum 
level of the volume. For details, see [Volume 
Limit] (page 85).(Language Follow)
When you change the language for the on-screen 
display of the TV, the system’s on-screen 
display language is also changed after turning 
the system off and on.
Enjoying TV sound from the 
speakers in this system
Setting the Maximum Volume 
Level of the System
Changing the language for the 
on-screen display of the TV
 
						

							Other Operations
69GB
Calibrating the 
Appropriate Settings 
Automatically
[Auto Calibration]
D. C. A. C. (Digital Cinema Auto Calibration) 
can set the appropriate surround sound 
automatically.
Note The system outputs a loud test sound when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and neighbors.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Auto Calibration], 
then press  .
The confirmation display for [Auto 
Calibration] appears.
5Connect the calibration mic to the 
A.CAL MIC jack on the rear panel.
Set up the calibration mic at ear level using 
a tripod, etc. (not supplied). The front of 
each speaker should face the calibration 
mic, and there should be no obstruction 
between the speakers and the calibration 
mic.
6Press X/x to select [Start].
To cancel, select [Cancel].
7Press .
[Auto Calibration] starts.
The system adjusts the speaker settings 
automatically.
Be quiet during the measurement.
Note Before [Auto Calibration], make sure that the 
surround amplifier turns on and you install the 
surround amplifier in the appropriate location. If 
you install the surround amplifier in an improper 
location, such as another room, proper 
measurement will not be obtained.
 When you use the Wireless Surround Speaker 
Kit (WAHT-SBP1, optional) for the surround 
back speakers (page 16), install the speakers in 
appropriate location and turn the surround 
amplifier on.
 Loud test sound is output when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and 
neighbors.
EZW-T100
AUD
IO
D
IG
IT
A
L
 INA
U
DIO
 I
NA
U
DIO
 I
N
A. CAL MICE
C
M
-A
C
2
COAXIALOPTICAL
R L
R LE
XTTV
TVD
IG
IT
A
L
 INS
A
T
/C
AB
L
EDC5V500mA  MAX
A
N
T
E
N
N
A
F
MC
O
A
X
I
A
L7
5
Calibration mic
 
						

							70GB
8Confirm the conclusions of [Auto 
Calibration].
The conclusions appear on the TV screen. 
Press C/c to change the page. The first page 
shows the distance of speakers. The second 
page shows the level of speakers.
Note If measurement fails, follow the message then 
retry [Auto Calibration].
9Press X/x to select [OK] or [Cancel], 
then press  .
xThe measurement is OK.
Disconnect the calibration mic, then select 
[OK]. The result is implemented.
xThe measurement is not OK.
Follow the message, then select [OK] to 
retry.
Note While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
– do not insert or eject a disc.
– do not connect the headphones to the surround 
amplifier.
– do not disconnect the calibration mic.
Setting the Speakers
[Speaker Settings]
To obtain the best possible surround sound, set 
connection of the speakers and their distance 
from your listening position. Then use the test 
tone to adjust the level and the balance of the 
speakers to the same level.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Speaker Settings], 
then press  .
The [Speaker Settings] display appears.
5Press X/x to select the item, press  .
Setup the following settings.
x[Connection]
If you do not connect center or surround 
speakers, set the parameters for [Center] and 
[Surround]. Since the front speaker and 
subwoofer settings are fixed, you cannot change 
them.
When you use the Wireless Surround Speaker 
Kit (WAHT-SBP1, optional) for the surround 
back speakers (page 16), set [Surround Back] 
also.
[Front]
[Yes]
[Center]
[Yes]: Normally select this.
[None]: Select this if no center speaker is used. 
[Surround]
[Yes]: Normally select this.
[None]: Select this if no surround speaker is 
used.
[Surround Back]
[Yes]: Select this if surround back speakers are 
used.
[None]
: Select this if no surround back speaker 
is used.