Smeg Sta6544tc Instruction Manual

 
User instructions   
 
 
9  
 
 
3.  Description of the controls  
 
3.1 Upper panel  All the dishwasher controls are grouped on the upper panel. Switch-on, 
programming, switch-off etc. procedures are only possible when the 
door is open.
 
  
 
 
1 ON/OFF BUTTON 
2 PROGRAM SELECTION BUTTON and INDICATOR LIGHT 
3 SALT WARNIN LIGHT 
4 RINSE AID WARNING LIGHT 
5 ENERSAVE BUTTON and LIGHT 
6 MULTIFUNCTION PRODUCT OPTION BUTTON and LIGHT 
7 SPEED PROGRAM BUTTON and LIGHT 
8 HALF LOAD BUTTON and LIGHT 
9...

 User instructions    
 
10 
SETTING THE WASHING PROGRAM AND SWITCHING ON To select the most suitable program for the dishes to be washed refer to 
the table below, which indicates the most appropriate program according 
to dish type and degree of soiling. 
 After using the table to identify the most appropriate washing program:  • press the ON/OFF button and wait for the PROGRAM INDICATOR 
LIGHT to illuminate; 
•  keep pressing the PROGRAM SELECTION button (2) 
corresponding to the desired program; 
•...

 
User instructions   
 
 
11 
PROGRAMME, NUMBER & SYMBOL  
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTES (1)  
WATER LITRES
 POWER KWh (1) 
1 SOAK 
 
Pans and dishes awaiting completion of the load. Cold prewash 15 3,5 0,02 
2 FAST 
 
Dishes with light dirt, washed immediately after use 
Wash at 38°C Rinse at 50°C 
 
27 
 
6,5 0,70 
3 GLASS 
 
Glass, china and mixed dishes with light dirt. 
Wash at 45°C Cold rinse Rinse at 70°C Dry 
 
65 
 
9,5 1,10 
4 ECO (*) 
 EN 50242...

 User instructions    
 
12 
QUICK TIME PROGRAMS 
 (see relevant section for explanation of functioning modes) 
 
PROGRAMME NUMBER E SYMBOL  
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTES (1)  
WATER LITRES POWER KWh (1) 
7 GLASS SPEED 
  +  
Glass, china and mixed dishes with light dirt. 
Wash at 50°C Cold rinse Rinse at 70°C 
 
60 
 
9,5 1,00 
8 ECO SPEED 
  +  
Dishes with normal dirt, even with dried-on residues. 
Cold prewash Wash at 60°C Cold rinse Rinse at 70°C 
 
70...

 
User instructions   
 
 
13 
 
NOTES AND REFERENCES Only run the soak program with half loads.  Options cannot be used with the soak program.  The ENERSAVE option (if featured) cannot be used with soak, ultra clean, or any 
programs which do not include the final drying stage. 
 * Standard programme under EN 50242. If present, the ENERSAVE option must 
be enabled. 
**  See information sheet provided 
*** IEC/DIN reference programme. If present, the ENERSAVE option must be 
enabled.
 
**** Reference...

 User instructions    
 
14                  3.2 Washing programs   
  
Before starting a washing program make sure that: 
• The water supply tap is open. 
• The correct amount of detergent has been added to the 
dispenser. 
• The baskets have been correctly loaded. 
• The spray arms are able to rotate freely and without 
obstruction. 
• The dishwasher door is securely closed.   
 
 QUICK TIME PROGRAMS Select this option together with any washing program (except the soak program) 
to SHORTEN the cycle by...

 
User instructions   
 
 
15 
 
SPREAD HALF LOAD Suitable when there are not many dishes to be washed, it saves energy 
and reduces the program duration.  Place dishes in both baskets then 
load the detergent dispenser than less than the normal amount for a full 
load.
 
 
 
MULTIFUNCTIONS DETERGENTS OPTION Ideal for multi-function detergents, this option allows washing to be 
optimised, with full benefits from the combined-action tablets. When this 
option is activated, any salt and rinse aid in the...

 User instructions    
 
16 
 CANCELLING THE CURRENT PROGRAM •  To cancel the currently selected program, open the door and hold 
down the PROGRAM SELECTION  button for a few seconds 
until the indicator lights for programs 5 and 6 illuminate 
simultaneously. 
 
 
 
•  Close the door. 
•  After approximately 1 minute the dishwasher will advance to the end 
of cycle. 
 
 CHANGING THE PROGRAM To change the program in progress, simply open the door and select a 
new program. When the door is closed the...

 
User instructions   
 
 
17  
 
 
  
 If the door has to be opened while washing is in progress, the program 
will be interrupted. The relative light will keep flashing and a beeper will 
signal that the cycle has not been completed. You must wait about 1 
minute before closing the door to restart the program. When the door is 
closed the program will continue from where it was interrupted. This 
operation should only be carried out if strictly necessary, because it 
might cause problems in execution...

 User instructions    
 
18  
 
 
 
 
 
 
 
4. Operating instructions  
 
 
Once the dishwasher has been correctly installed, prepare for use as 
follows: 
 •  Adjust the water softening system; 
•  Add the regenerating salt; 
•  Add the rinse aid and detergent. 
 
 
4.1  Using the water softening system  
 
 
 
 The amount of scale contained in the 
water (water hardness index) can cause 
whitish staining on the dry dishes, which 
tend to become dull over time. The 
dishwasher is equipped with an...