Smeg Sta6539l Instruction Manual
Have a look at the manual Smeg Sta6539l Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions
9
3. Description of the controls
3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on,
programming, switch-off etc. procedures are only po ssible when the
door is open.
1 ON/OFF BUTTON
Pressing this button energises the appliance.
2
SELECTED PROGRAM INDICATOR LIGHTS
Illumination of this light denotes the program sele cted and the
occurrence of a fault (troubleshooting).
3
PROGRAM SELECTION BUTTON
By pressing this button in sequence it is possible to select the
desired program.
4
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT
The light flashes to indicate that the appliance is in “water hardness
adjustment” mode.
SALT WARNIN LIGHT (on some models only)
If the symbol is present, illumination of this lig ht denotes a
regenerating salt warning level.
5 RINSE AID WARNING LIGHT (on some models only)
Illumination of this light signals that rinse aid d ispenser is empty.
6
QUICK TIME + EXTRA OPTION BUTTON
(see “EXTRA OPTIONS” section)
The button controls selection of the quick time pro grams.
(see table).
7
QUICK TIME PROGRAM LIGHT
Illuminates to indicate that one of the extra progr ams (see table) is
going to be executed.
User instructions
10
8
ENERSAVE OPTION + EXTRA OPTION BUTTON
(see “EXTRA OPTIONS” section)
Press the button to enable/disable the option.
9 ENERSAVE OPTION LIGHT
Illuminates to indicate that the function is activa ted.
10 HALF LOAD BUTTON
Press this button to activate the half load wash op tion.
11 HALF LOAD LIGHT
Illuminates to indicate that the function is activa ted.
12 3/1 OPTION (EXTRA OPTION) LIGHT
Illuminates to indicate that the function is activa ted.
13 PROGRAM DELAY BUTTON
Press this button to delay the start of the program .
14 INFORMATION DISPLAY (1 or 3 digits depending on model)
N.B.: symbols and styling are guideline and may vary dep ending on
the model or version of the dishwasher purchased.
Information displayed
Scheduled program duration yes
Remaining program time yes
Delayed start 1 - 24 hours
Error message Err
User instructions
11
PROGRAMS TABLE The manual contains the programs table for several models. To find the
table for your dishwasher, compare the program symb ols at the top of the
table with those on your control panel.
SETTING THE WASHING PROGRAM AND SWITCHING ON After identifying the most suitable program with th e aid of the programs
table:
· Press the ON/OFF button (1) and wait for the PROGRAM
INDICATOR LIGHT (2) to illuminate;
· Keep pressing the PROGRAM SELECTION button (3) until the
indicator light corresponding to the desired progra m illuminates;
· select the option required (if any and if the mode l provides options);
· close the door; after about 2 the program will start LIGHT will
flashing (indicating that the program is being exec uted).
User instructions
12
PROGRAMS TABLE
PROGRAMME, NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY
PROGRAM PROGRESS
DURATION
CONSUMPTION MINUTES (1)
WATER LITRES
POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load. Cold prewash
15
3,5 0,02
2 LIGHT
Delicate dishes with normal dirt.
Wash at 45°C Cold rinse Rinse at 70°C Dry
65
9,5 1,10
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues.
Cold prewash Wash at 50°C Cold rinse Rinse at 55°C Dry
**
** **
4 AUTO 60-70
IEC/DIN***
Pans and dishes with normal dirt, even with dried-on residues.
When the AUTO program is selected, the dishwasher recognises the type of dirt and automatically adjus ts the washing parameters as appropriate.
5 SUPER
****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (2) Rinse at 70°C Dry
155
15,5 1,60
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
The washing cycle will not take place if the dishwa sher door is left open
or not properly closed.
User instructions
13
QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes)
PROGRAMME NUMBER E SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION
CONSUMPTION MINUTI (1)
WATER LITRES
POWER KWh (1)
6 RAPID 27’
+
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
7 ECO QUICK
+
Dishes with normal dirt, washed immediately after use.
Cold prewash Wash at 55°C Cold rinse Rinse at 70°C
80
12,5 1,25
8 DAILY
+
Dishes with normal dirt, washed immediately after use.
Wash at 65°C Cold rinse Rinse at 70°C Dry
95
11 1,25
9 STRONG and FAST
+
Mixed dishes with normal dirt without dried-on residues.
Wash at 65°C Cold rinse Rinse at 70°C 55 9,5 1,35
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
The washing cycle will not take place if the dishwa sher door is left open
or not properly closed.
User instructions
14
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION MINUTES (1)
WATER LITRES POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02
2 GLASS
Glass, china and mixed dishes with light dirt.
Wash at 45°C Cold rinse Rinse at 70°C Dry
65
9,5 1,10
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 50°C Cold rinse Rinse at 55°C Dry
**
** **
4 NORMAL
IEC/DIN***
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry
105
13,5 1,35
5 ULTRA CLEAN
****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (2) Rinse at 70°C Dry
160
15,5 1,70
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. The ULTRA CLEAN program terminate with an extra anti-bacteria rins e that ensures a
further reduction in the bacteria level. If the tem perature falls during this stage of the
program (e.g. because the door is opened or due to a power blackout), the program
lights flash to warn that the anti-bacteria effect is not guaranteed.
If the dishwasher door is open or not properly clos ed, the washing cycle
will not start.
User instructions
15
QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes)
PROGRAMME NUMBER E SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION
CONSUMPTION MINUTI (1)
WATER LITRES
POWER KWh (1)
6 RAPID 27’
+
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
7 ECO QUICK
+
Dishes with normal dirt, washed immediately after use.
Cold prewash Wash at 55°C Cold rinse Rinse at 70°C
80
12,5 1,25
8 DAILY
+
Dishes with normal dirt, washed immediately after use.
Wash at 65°C Cold rinse Rinse at 70°C Dry
95
11 1,25
9 STRONG and FAST
+
Mixed dishes with normal dirt without dried-on residues.
Wash at 65°C Cold rinse Rinse at 70°C
55
9,5 1,35
If the dishwasher door is open or not properly clos ed, the washing cycle
will not start.
User instructions
16
NOTES AND REFERENCES Only run the soak program with half loads. Options cannot be used with the soak program.
* Standard programme under EN 50242. If present, the ENERSAVE option must
be enabled .
** See information sheet provided
*** IEC/DIN reference programme. If present, the ENERSAVE option must be
enabled.
**** Reference program for laboratories: Detergent: 25g in the dispenser + 10g in
the door or tablet. Configuration : see photo in “Using the baskets”.
(1) The cycle duration and power consumption may va ry according to the water
and room temperatures, and the type and amount of d ishes.
(2) 1 or 2 cold rinses depending on the model.
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
- Annual energy consumption is based on 280 standard wash cycles with
cold water and consumption of low-energy operating modes. Actual
consumption depends on the way in which the applian ce is used.
- Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the applian ce is used.
- Information refers to the
EN 50242 STANDARD programme (identified in the
programmes table), which is the most effective in t erms of combined energy
and water consumption. The programme is recommended for dishes with a
normal level of dirt.
- Energy consumption in “sleep” mode = 0.02 W.
- Energy consumption in “on” mode = 1.5 W.
- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions
17
3.2 Washing programs
Before starting a washing program make sure that:
· The water supply tap is open.
· The correct amount of detergent has been added to the
dispenser.
· The baskets have been correctly loaded.
· The spray arms are able to rotate freely and without
obstruction.
· The dishwasher door is securely closed.
QUICK TIME PROGRAMS Select this option together with any washing progra m (except the soak program)
to SHORTEN the cycle by from a minimum of 10% to a maximum of 55%,
depending on the cycle selected. To activate this o ption, press the QUICK TIME
button (light comes on) after selecting the progra m required. The option is
automatically deactivated at the end of the program .
ENERSAVE This option can be selected with the wash programme of choice to
further reduce energy consumption. Drying is aided by a special device
that automatically releases the door, which opens s lowly and smoothly
by a few centimetres. This ensures perfect drying a nd greater control of
rinsing temperatures, which can be kept at lower le vels for significant
energy saving.
Once the door has opened, the dishwasher
emits a short
beep and programme lights
nos. 4 and 5 (marked “end”) flash to indicate
the end of the washing cycle.
Enersave
is activated automatically every time a wash cycle is
selected (except for programs that do not include t he final drying phase;
see programs table) and can be disabled before the program is started.
When the function is activated, opening of the door must not be
impeded in any way; do not leave anything in the space in front of th e
door necessary to allow it to open.
Do not re-close the door during automatic opening as this would
damage the mechanism. Wait for the pushers to retract before re-closing
the door.
User instructions
18
SPREAD HALF LOAD Suitable when there are not many dishes to be washe d, it saves energy
and reduces the program duration. Place dishes in both baskets then
load the detergent dispenser than less than the nor mal amount for a full
load.
EXTRA OPTIONS - “Flexi Tabs” BUTTON Press buttons 6 + 8 (QUICK TIME PROGRAMS button + ENERSAVE
option button) simultaneously to activate the Flexi Tabs option; the
respective light comes on to confirm the selection. The option is
optimised for use of detergents which are complete with salt and rinse
aid, known on the market as, triple action, etc. With this option
activated, any salt and rinse aid If you wish to us e detergents which
already contain salt and rinse aid already in the d ishwasher will not be
used.
N.B.: even with the Flexi Tabs option selected, the regenerating
salt/rinse aid lights will still stay on if their c ontainers are empty.
IMPORTANT: the option continues to be active until it is deactivated by
pressing buttons 6 + 8 simultaneously; the light will then go out.
This products are not suitable for use with excessi vely hard water.
Therefore, if the water hardness is set higher than H3, the Flexi Tabs
OPTION light flashes to indicate a setting error. This does not prevent
the use of the option, but the washing results migh t not be of the best.
DELAYED START The start of the washing program can be delayed to program the
dishwasher to operate at the preferred time of day (e.g. overnight). Press
the PROGRAM DELAY button to activate the option and display a 1 hour
delay. Keep pressing to select the delay required, which may be up to 9,
12 or 24 hours depending on the model.
When the door is closed, the appliance will prewash the dishes, after
which the program delay set will come into effect .