Smeg St313 Instruction Manual
Have a look at the manual Smeg St313 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions
9
3. Description of the controls
3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on,
programming, switch-off, etc. procedures are only p ossible when the door is
open.
The panel shown is only a guideline example: the fo rm of the lights and
buttons may vary depending on the model.
1 ON/OFF BUTTON
Press this button to switch the dishwasher on/off.
2
SELECTED PROGRAM INDICATOR LIGHTS
Illumination of this light denotes the program sele cted and the
occurrence of a fault (troubleshooting).
3
PROGRAM SELECTION BUTTON
+ ADJUSTING THE WATER SOFTENING SYSTEM
Used to select the washing program required and adj ust the water
softening system.
4
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT
The light flashes to indicate that the appliance is in “water hardness
adjustment” mode.
SALT WARNING LIGHT (on some models only)
If the symbol is present, illumination of this lig ht denotes a
regenerating salt warning level.
5 RINSE AID WARNING LIGHT (on some models only)
Illumination of this light denotes a rinse aid warn ing level in the tank.
6 OPTIONS (on some models only)
User instructions
10
Depending on the model, this zone may contain one o r more of the
following options, identified by the relative symbo ls and described in
more detail in the relevant sections of the manual.
It is not possible to select any options when the soak program is being
used. All options except Flexi Tabs are disabled at the end of the
wash cycle. To disable the “Flexi tabs” option, press the relative
button (the light goes out).
Flexi Tabs
Specifically for the use of products which contain salt and
rinse aid as well as detergent.
HYCLEAN
Adds a final antibacterial rinse to the selected pr ogram.
Spread HALF LOAD WASH
Allows washing of just a few dishes placed in both baskets.
PROGRAM DELAY
Allows the program to be set to start with a delay of 3, 6 or 9
hours.
User instructions
11
PROGRAMS TABLE The manual contains the programs table for several models. To find the
table for your dishwasher, compare the program symb ols at the top of the
table with those on your control panel.
SETTING THE WASHING PROGRAM AND SWITCHING ON After identifying the most suitable program with th e aid of the programs
table:
· Press the ON/OFF button (1) and wait for the PROGRAM
INDICATOR LIGHT (2) to illuminate;
· Keep pressing the PROGRAM SELECTION button (3) until the
indicator light corresponding to the desired progra m illuminates;
· select the option required (if any and if the mode l provides options);
· close the door; after about 2 the program will start LIGHT will
flashing (indicating that the program is being exec uted).
User instructions
12
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION MINUTES (1)
WATER LITRES POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02
2 RAPID
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 50°C (2) Rinse at 66°C Dry
**
** **
4 NORMAL
IEC/DIN***
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry
105
13,5 1,35
5 ULTRA CLEAN
****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (3) Rinse at 70°C Dry
155
15,5 1,60
The ULTRA CLEAN program terminate with an extra anti-bacteria rinse that ensures
a further reduction in the bacteria level. If the temperature falls during this stage of
the program (e.g. because the door is opened or due to a power blackout), the
program lights (4) flash to warn that the anti-bacteria effect is not guaranteed.
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions
13
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION MINUTES (1)
WATER LITRES POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02
2 RAPID
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 50°C (2) Rinse at 66°C Dry
**
** **
4 NORMAL
IEC/DIN***
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry
105
13,5 1,35
5 SUPER
****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (3) Rinse at 70°C Dry
155
15,5 1,60
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions
14
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION MINUTES (1)
WATER LITRES POWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02
2 RAPID
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 50°C (2) Rinse at 66°C Dry
**
** **
4 HALF LOAD
Half load of dishes with normal dirt, washed immediately after use.
Wash at 65°C Cold rinse Rinse at 70°C Dry
90
11 1,20
5 SUPER
****
Very dirty pans and dishes, even with dried-on residues.
Hot prewash Wash at 70°C Cold rinse (3) Rinse at 70°C Dry
155
15,5 1,60
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions
15
NOTES AND REFERENCES Only run the soak program with half loads. Options cannot be used with the soak program.
* Standard programme under EN 50242.
** See information sheet provided
*** IEC/DIN reference programme.
**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in
the door or tablet. Configuration : see photo in “Using the baskets”.
(1) The cycle duration and power consumption may va ry according to the water
and room temperatures, and the type and amount of d ishes.
(2) Some models feature an intermediate rinse.
(3) 1 or 2 cold rinses depending on the model.
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
- Annual energy consumption is based on 280 standard wash cycles with cold
water and consumption of low-energy operating modes . Actual consumption
depends on the way in which the appliance is used.
- Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the applian ce is used.
- Information refers to the
EN 50242 STANDARD programme (identified in the
programmes table), which is the most effective in t erms of combined energy
and water consumption. The programme is recommended for dishes with a
normal level of dirt.
- Energy consumption in “sleep” mode = 0.02 W.
- Energy consumption in “on” mode = 1.5 W.
- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions
16 3.2 Washing programs
Before starting a washing program make sure that:
· The water supply tap is open.
· The softener container contains regenerating salt .
· The correct amount of detergent has been added to the
dispenser.
· The baskets have been correctly loaded.
· The spray arms are able to rotate freely and without
obstruction.
· The dishwasher door is securely closed.
OPTION SELECTION
Options are selected by pressing the relative butto n by the symbol of the
option required; the light comes on to confirm that the option has been
activated.
· It is not possible to select any options when the soak
program is being used.
· All options except Flexi tabs are disabled at the end of the
wash cycle. To disable the “Flexi tabs” option, press the
relative button (the light goes out).
· All options, including Flexi tabs are disabled when a program
is CANCELLED after it has begun.
ADDITIONAL OPTIONS
Some models feature additional options, activated b y pressing two
buttons simultaneously . In this case, two lines in the control panel
graphics link the symbol of the additional option t o the two buttons to be
pressed simultaneously to enable it. (e.g. “Flexi Tabs” in this
illustration)
User instructions
17
Flexi Tabs
Ideal for multi-function detergents, this option allows washing to be
optimised, with full benefits from the combined-act ion tablets. When this
option is activated, any salt and rinse aid in the relative containers will
not be used.
If the option is not provided , we recommend the use of conventional
products (separate detergent, salt and rinse aid), because with
conventional washing cycles, combined products migh t create problems
such as a white deposit, poor drying results and re sidues left on dishes.
N.B.:
When the salt and rinse aid containers are empty, t he relative lights will
remain on even if the “Flexi Tabs” option is selected.
IMPORTANT:
when no longer required, the option must be deactivated by pressing
the relative button (the light goes out).
If the water hardness has been set on a value above H3 , and the “Flexi
Tabs ” option is activated, the relative light flashes, warning of a setting
error. Multi-function products are not suitable for use with very hard
water; this does not prevent the use of the option, but the washing
results might not be of the best.
ULTRA CLEAN The ULTRA CLEAN program prolongs the final hot rinse to ensure a
further reduction in the bacteria level. If the tem perature in the tank falls
during this stage of the program (e.g. because the door is opened or due
to a power blackout), the light of the option and t he program lights (2) flash
to warn that the additional washing phase has not b een completed
successfully. This does not mean that the wash prog ram has been less
effective than usual.
SPREAD HALF LOAD
Suitable when there are not many dishes to be washe d, it saves energy
and reduces the program duration. Place dishes in both baskets then
load the detergent dispenser than less than the nor mal amount for a full
load.
User instructions
18
PROGRAM DELAY
The start of the program can be delayed by 3, 6 or 9 hours.
This allows you to set the dishwasher to work at th e times of day most
convenient to you. After setting the program , press the button to select
the delay you require; the corresponding light will come on. When the
door is closed, the appliance will prewash the dish es, after which the
program delay set will come into effect. If you w ish to exit the
procedure without setting delayed start, press the button in sequence
until all three lights are out.
N.B.: It is not possible to select the PROGRAM DELAY option once the
cycle has begun.
CANCELLING THE CURRENT PROGRAM · To cancel the currently selected program open the door and hold
down the PROGRAM SELECTION (3) button for a few seconds
until the indicator lights for programs 4 and 5 illuminate
simultaneously (marked end).
· Close the door.
· After approximately 1 minute the dishwasher will a dvance to the end
of cycle.
CHANGING THE PROGRAM To change the program in progress, simply open the door and select a
new program. When the door is closed the dishwasher will automatically
select the new program.