Smeg St 147 Instruction Manual

 
 
User instructions   
 
 
9  
 
 
3.  Description of the controls  
3.1 Front panel 
 
The ON/OFF is on the top edge of the panel, and all the dishwasher’s 
other controls and monitoring devices are on the central display. 
Programming and option selection are only possible with the door 
closed. 
 
 
 
 
NOTA: 
The displays illustrated in the instruction manual are purely guideline; 
symbols, programs and options may vary depending on the model 
purchased. 
 
 
 
 
 
 
The 4-figure INFORMATION...

 
 
User instructions   
 
10   
 
 
 
1 ON/OFF BUTTON 
2 SELECTION PROGRAMS BUTTON 
3 START/PAUSE BUTTON 
4 PROGRAMS LIGHTS 
5 PHASES/PROGRAM LIGHTS + 
PROGRAM DELAY (if the option is included) 
6 
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT 
The light flashes to indicate that the appliance is in “water 
hardness adjustment” mode. 
SALT WARNIN LIGHT 
Illumination of this light denotes a regenerating salt warning level. 
7 NO RINSE AID LIGHT 
8 OPTIONS (on some models only) 
9 INFORMATION DISPLAY...

 
 
User instructions   
 
 
11  
 
 
 
Depending on the model, this zone may contain one or more of the 
following options, identified by the relative symbols and described in 
more detail in the relevant sections of the manual. 
It is not possible to select any options when the soak program is being 
used. All options except Flexi Tabs are disabled at the end of the 
wash cycle. To disable the “Flexi Tabs” option, press the relative 
button (the light goes out).
 
 
 
Flexi Tabs 
Specifically for the...

 
 
User instructions   
 
12  
 
 
 
PROGRAMS TABLE 
         DURATION  CONSUMPTION PROGRAMME NUMBER & SYMBOL 
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS  MINUTES (1)  
 WATER LITRESPOWER KWh (1) 
1 SOAK 
 
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02 
2 RAPID 
 
Dishes with light dirt, washed immediately after use 
Wash at 38°C Rinse at 50°C 
 
27 
 
6,5 0,70 
3 NORMAL ECO (*)  
 
Crockery and cutlery normally soiled 
Cold prewash Wash at 45°C Rinse at 45°C Dry 
147’ 12,6...

 
 
User instructions   
 
 
13 
3.2 Washing programs    The dishwasher is equipped with a control panel, described in chapter 
3. Description of the controls, from which it is possible to carry out all 
the power switch-on, switch-off and programming operations. 
 
 
  
 Before starting a washing program make sure that: 
• The water supply tap is open. 
• The correct amount of detergent has been added to the 
dispenser. 
• The baskets have been correctly loaded. 
• The spray arms are able to rotate...

 
 
User instructions   
 
14  STARTING THE PROGRAM 
 To start the dishwasher, press the START/PAUSE button (3) for a few 
seconds, until the light of the first phase of the selected program starts to 
flash (confirmation beep). 
As the program runs, the PHASES/PROGRAM lights (5) will indicate the 
current cycle status. 
 
 
 
  The light of the phase in progress will flash, while the lights of the 
subsequent phases remain on. 
  
   END OF PROGRAM   
At the end of the program, a short beep sounds, the...

 
 
User instructions   
 
 
15  
 ANNULLING A PROGRAM  To annul the program  
• press the START/PAUSE button (3 ) for a few seconds; the light of 
the phase in progress remains on and the light of the program in 
progress flashes (confirmation beep); 
• Keep the START/PAUSE button (3) pressed until the PROGRAM 
PHASES lights (5) go out (confirmation beep). “ 
P0 ” will appear on 
the DISPLAY and pump-out of the water in the tank will begin, 
ending the program at the point where it was interrupted. When...

 
 
User instructions   
 
16  
  
If the water hardness has been set on a value above H3, and the “Flexi 
Tabs” option is activated, the relative  light flashes, warning of a setting 
error. Integrated products are not suitable for use with very hard water; 
this does not prevent the use of the option, but the washing results 
might not be of the best.  
 
HYCLEAN  Increases the temperature of the final hot rinse to 70°C to ensure a further 
reduction in the bacteria level. If the temperature in the...

 
 
User instructions   
 
 
17  
  
 TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT  
• Always try to run the dishwasher fully loaded. 
• Do not wash the dishes in running water. 
• Use the washing program that is most appropriate for each type of 
load. 
• Do not carry out any preliminary rinsing. 
• If available, connect the dishwasher to a hot water supply up to 
60°C.  TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT 
THE ENVIRONMENT  The phosphates contained in dishwasher detergents are...

 
 
User instructions   
 
18  
 
 
 
 
 
 
 
 
4. Operating instructions  
 
 
Once the dishwasher has been correctly installed, prepare for use as 
follows: 
 •  Adjust the water softening system; (present only on some models) 
•  Add the regenerating salt; 
(only on some models) 
•  Add the rinse aid and detergent. 
 
 
4.1 Using the water softening system (only on some models)  
 
 
 
 The amount of scale contained in the 
water (water hardness index) can cause 
whitish staining on the dry dishes,...