Smeg Sc436x8 Manual

Instructions for the user
73  Spray a water and washing up
liquid solution inside the oven using
a spray nozzle. Aim the spray
towards the side walls, roof, floor
and deflector (the coloured zone on
the figure to the side shows where
the solution can be sprayed).
Do not spray excessive amounts of the water and washing up liquid solution. We
recommend spraying approx. 20 times at the most.
 Close the door and set the assisted cleaning cycle.
9.7.2 Setting the assisted cleaning cycle
Once the preparations...

Instructions for the user
749.7.3 End of the assisted cleaning cycle
The water remaining at the end of the assisted cleaning cycle cannot be left
inside the oven for long (for example overnight).
You are advised to wear a pair of gloves during these processes.
At the end of the cleaning cycle, open the door and wipe away the less stubborn
dirt with a microfibre cloth. Use an anti-scratch sponge with brass filaments on
tougher encrustations.
We recommend removing the door as described in “10.2 Removing...

Instructions for the user
75
10.EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as gaskets, bulbs, etc. The following instructions describe
how to carry out these minor maintenance operations.
Before any intervention that requires access to live parts, disconnect the
power supply of the appliance.
10.1 Replacing the light bulb
If a light bulb needs to be replaced because it is worn or burnt out (in
multifunction models remove the guide...

Instructions for the user
76
10.2 Removing the door
10.2.1 With pins
Open the door completely.
Insert two pins into the holes indicated
A in the two hinges towards the back of
them until they engage.
Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
To reassemble the door, put the hinges
in the relevant slots in the oven, making
sure that grooved sections C are
resting completely in the slots.  Lower
the door and once it is in place remove
the pins from...

Instructions for the user
77
10.3 Removing the door seal
To permit thorough cleaning of the
oven, the door seal may be removed.
There are fasteners on all four sides to
attach it to the edge of the oven. Pull
the edges of the seal outwards to
detach the fasteners.
10.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. To facilitate
cleaning, it is possible to remove the door (see 10.2 Removing the door) and
place it on a canvas, or open it and lock the...

Instructions for the user
78
Removing the internal glass panel:
 Remove the internal glass panel by
pulling it upwards, following the
movement indicated by the arrows. Doing
this detaches the 4 pins attached to the
glass from their slots in the oven door.
Removing the intermediate glass panels
(on some models only):
 Some multifunction models have an
intermediate glass panel. Remove the
intermediate panel by lifting it upwards.
Cleaning:
 It is now possible to clean the external
glass panel and the...

Instructions for the installer
79
11.INSTALLING THE APPLIANCE
11.1 Electrical connection
The identification plate bearing the technical data, serial number and brand
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
The appliance must be connected to earth in compliance with electrical system
safety regulations.
If a fixed connection is being used, fit the power line with an omnipolar circuit-
breaker in accordance with the installation rules, located in a position...

Instructions for the installer
80
11.3 Positioning the oven
Never use the oven door to lever the oven into place when fitting. Avoid exerting
too much pressure on the oven door when open.
We recommend installing the oven with the help of a second person.
The base on which the oven is resting must be complete as shown in the
illustrations below.
The oven is designed for mounting into any piece of furniture as long as it is
heat-resistant (90°C).
Proceed according to the dimensions shown in figures 1, 2...

Instructions for the installer
81
FIG.1
ABCDE
Measurements 
(mm)583 ÷ 585554 ÷ 564 490 ÷ 500560 min.35 ÷ 40 

Instructions for the installer
82
FIG. 2 FIG. 3
FIG. 4 FIG. 5