Smeg Pla6442x Instruction Manual

 
User instructions   
 
 
9  
 
 
3.  Description of the controls  
3.1 Front panel  All the dishwasher controls are grouped on the front panel. 
 
 
 
1 ON/OFF BUTTON 
2 SELECTION PROGRAM BUTTONS (P1…P5) 
3 OPTION SELECTION BUTTON
4 CONFIRM OPTIONS BUTTON 
5 DELAY PROGRAM BUTTON 
6 START/PAUSE BUTTON 
7 POWER ON LIGHT 
8 PROGRAMS INDICATOR LIGHTS 
9 INFORMATION DISPLAY 
10 RECESSED DOOR HANDLE 
 
N.B.: symbols and styling are guideline and may vary depending on 
the model or version of the dishwasher...

 User instructions    
 
10 
 
3.2 Information display 
  The dishwasher is equipped with a practical DISPLAY which provides 
information on the programmed dishwasher functions. 
 
 
  
 
 
A 4-FIGURE DISPLAY 
B RINSE AID WARNING LIGHT 
C SALT WARNING LIGHT 
D START/PAUSE BUTTON 
E OPTIONS LIGHT  
 
  
PROGRAMS TABLE The manual contains the programs table for several models. To find the 
table for your dishwasher, compare the program symbols at the top of the 
table with those on your control panel....

 
User instructions   
 
 
11  PROGRAMS TABLE 
 
 
PROGRAMME NUMBER & SYMBOL 
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTES (1)  
 WATER LITRESPOWER KWh (1) 
1 SOAK 
 
Pans and dishes awaiting completion of the load Cold prewash 15 3,5 0,02 
2 GLASS 
 
Glass, china and mixed dishes with light dirt. 
Wash at 45°C Cold rinse Rinse at 70°C Dry 
 
65 
 
9,5 1,10 
3 ECO (*) 
 EN 50242 
Dishes with normal dirt, even with dried-on residues 
Cold prewash Wash at 50°C Cold rinse Rinse...

 User instructions    
 
12 
QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes)  
 PROGRAMME NUMBER E SYMBOL  
LOAD CROCKERY AND CUTLERY  PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTI (1)  
WATER LITRES POWER KWh (1) 
6 RAPID 27’ 
+ 
Dishes with light dirt, washed immediately after use 
Wash at 38°C Rinse at 50°C 
 
27 
 
6,5 0,70 
7 ECO QUICK 
+ 
Dishes with normal dirt, washed immediately after use. 
Cold prewash Wash at 55°C Cold rinse Rinse at 70°C 
 
80 
 
12,5 1,25 
8...

 
User instructions   
 
 
13 
NOTES AND REFERENCES Only run the soak program with half loads.  Options cannot be used with the soak program.  The ENERSAVE option cannot be used with soak, ultra clean, or any programs 
which do not include the final drying stage. 
 * Standard programme under EN 50242. The ENERSAVE option must be 
enabled. 
**  See information sheet provided 
*** IEC/DIN reference programme. The ENERSAVE option must be enabled. 
**** Reference program for laboratories: Detergent: 20g in...

 User instructions    
 
14 
3.3 Washing programs   The dishwasher is equipped with a control panel and an INFORMATION 
DISPLAY from which it is possible to carry out all the power switch-on, 
switch-off and programming operations. 
  
  
 Before starting a washing program make sure that: 
• The water supply tap is open. 
• The correct amount of detergent has been added to the 
dispenser. 
• The baskets have been correctly loaded. 
• The spray arms are able to rotate freely and without 
obstruction. 
•...

 
User instructions   
 
 
15 
 START PROGRAM
At this point, in order to start the machine, it is only enough to press the 
START/PAUSE (6) for some seconds until the symbol START/PAUSE 
(D) start to flash and confirmation “beep” is heard. From this moment the 
cycle duration on the DISPLAY (9) starts to decrease. 
This phase, that updates itself during the cycle, is “indicative” since it is 
influenced by the washing conditions such as dishwasher type and 
quantity, entry temperature etc. For this...

 User instructions    
 
16 
 STOPPING A PROGRAM
To cancel a program which is running: 
•  Interrupt the program (see 
INTERRUPTING A PROGRAM) 
• Press the START/PAUSE button   and hold it down; the 
display will show P0 and the dishwasher will immediately 
switch to the end of the cycle and drain the tank (during this 
process, the START/PAUSE symbol will flash). When the 
drain procedure ends, the end of cycle End message 
appears on the display. 
 
 
 
 
  
 In case that the door is opened during the...

 
User instructions   
 
 
17 
 PROGRAM DELAY
 
The PROGRAM DELAY  button can be pressed to delay the start of the 
washing program by from 1 to 12/24 hours depending on the model. This 
option allows the dishwasher to be operated at the time of day of the users 
choice. The first time the PROGRAM DELAY   button is pressed the 
option light comes on and 1:h appears on the DISPLAY.  The button can 
then be pressed again, to set the delay required (
2:h, 3:h, … etc.). If no 
button is pressed for a few...

 User instructions    
 
18  
 OPTIONS   The options are controlled by the OPTION 
SELECTION button . 
Press the button to access the procedure, 
confirmed by flashing of one of the OPTIONS 
lights (E). 
 
 N.B.: ThePROGRAM DELAY light only comes on when the specific 
PROGRAM DELAY button  is pressed. 
 
 
 
 
Press the SELECT OPTIONS button  again to display the next option. 
To confirm an option, press the CONFIRM OPTION button   (the light 
stops flashing and remains on). This operation can be carried...