Smeg Blv2r 1 Instruction Manual

 
User instructions   
 
 
9  
 
 
3.  Description of the controls  
3.1 Upper panel  All the dishwasher controls are grouped on the upper panel. Switch-on, 
programming, switch-off etc. procedures are only possible when the 
door is open.
   
  
 
1 ON/OFF BUTTON 
Pressing this button energises the appliance. 
2 
SELECTED PROGRAM INDICATOR LIGHTS 
Illumination of this light denotes the program selected and the 
occurrence of a fault (troubleshooting). 
3 
PROGRAM SELECTION BUTTON 
By pressing this...

 User instructions    
 
10 
8 
ENERSAVE OPTION + EXTRA OPTION BUTTON 
(see “EXTRA OPTIONS” section) 
Press the button to enable/disable the option. 
9 ENERSAVE OPTION LIGHT  
Illuminates to indicate that the function is activated. 
10 HALF LOAD BUTTON 
Press this button to activate the half load wash option. 
11 HALF LOAD LIGHT 
Illuminates to indicate that the function is activated. 
12 Flexi Tabs OPTION (EXTRA OPTION) LIGHT 
Illuminates to indicate that the function is activated. 
13 PROGRAM DELAY...

 
User instructions   
 
 
11 
 PROGRAMME, NUMBER & SYMBOL  
 LOAD CROCKERY AND CUTLERY 
 PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTES (1)  
WATER LITRES
 POWER KWh (1) 
1 SOAK 
 
Pans and dishes awaiting completion of the load. Cold prewash 
 
15 
 
3,5 0,02 
2 LIGHT 
 
Delicate dishes with normal dirt.
Wash at 45°C Cold rinse Rinse at 70°C Dry 
 
65 
 
9,5 1,10 
 3 ECO (*) 
 EN 50242 
Dishes with normal dirt, even with dried-on residues. 
Cold prewash Wash at 50°C Cold rinse Rinse at 70°C Dry 
 
**...

 User instructions    
 
12 
QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes) 
 
 PROGRAMME NUMBER E SYMBOL  
LOAD CROCKERY AND CUTLERY  PROGRAM PROGRESS 
DURATION  CONSUMPTION 
MINUTI (1)  
WATER LITRES POWER KWh (1) 
6 RAPID 27’ 
+ 
Dishes with light dirt, washed immediately after use 
Wash at 38°C Rinse at 50°C 
 
27 
 
6,5 0,70 
7 ECO QUICK 
+ 
Dishes with normal dirt, washed immediately after use. 
Cold prewash Wash at 55°C Cold rinse Rinse at 70°C 
 
80 
 
12,5 1,25...

 
User instructions   
 
 
13 
 
NOTES AND REFERENCES Only run the soak program with half loads.  Options cannot be used with the soak program.  The ENERSAVE option (if featured) cannot be used with soak, ultra clean, or any 
programs which do not include the final drying stage. 
 * Standard programme under EN 50242. If present, the ENERSAVE option must 
be enabled. 
**  See information sheet provided 
*** IEC/DIN reference programme. If present, the ENERSAVE option must be 
enabled.
 
**** Reference...

 User instructions    
 
14 
3.2 Washing programs   
  
Before starting a washing program make sure that: 
• The water supply tap is open. 
• The correct amount of detergent has been added to the 
dispenser. 
• The baskets have been correctly loaded. 
• The spray arms are able to rotate freely and without 
obstruction. 
• The dishwasher door is securely closed.   
 
 
 QUICK TIME PROGRAMS Select this option together with any washing program (except the soak program) 
to SHORTEN the cycle by from a...

 
User instructions   
 
 
15 
 
 
SPREAD HALF LOAD Suitable when there are not many dishes to be washed, it saves energy 
and reduces the program duration.  Place dishes in both baskets then 
load the detergent dispenser than less than the normal amount for a full 
load.
 
 
 
 
 EXTRA OPTIONS - “Flexi Tabs” BUTTON
 Press buttons 6 + 8 (QUICK TIME PROGRAMS button + ENERSAVE 
option button) simultaneously to activate the Flexi Tabs option; the 
respective light comes on to confirm the selection. The...

 User instructions    
 
16 
 
 CANCELLING THE CURRENT PROGRAM
 •  To cancel the currently selected program, open the door and hold 
down the PROGRAM SELECTION (3) button for a few seconds 
until the indicator lights for programs 4 and 5 illuminate 
simultaneously (the word end is displayed on the window). 
 
 
 
•  Close the door. 
•  After approximately 1 minute the dishwasher will advance to the end 
of cycle. 
 
 
 
 
 
 
 CHANGING THE PROGRAM To change the program in progress, simply open the door...

 
User instructions   
 
 
17  
  
 TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT  
• Always try to run the dishwasher fully loaded. 
• Do not wash the dishes in running water. 
• Use the washing program that is most appropriate for each type of 
load. 
• Do not carry out any preliminary rinsing. 
• If available, connect the dishwasher to a hot water supply up to 60°C. 
• Use the ENERSAVE option. 
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT 
THE ENVIRONMENT  The phosphates contained in...

 User instructions    
 
18  
 
 
 
 
 
 
 
4. Operating instructions  
 
 
Once the dishwasher has been correctly installed, prepare for use as 
follows: 
 •  Adjust the water softening system; 
•  Add the regenerating salt; 
•  Add the rinse aid and detergent. 
 
 
4.1  Using the water softening system  
 
 
 
 The amount of scale contained in the 
water (water hardness index) can cause 
whitish staining on the dry dishes, which 
tend to become dull over time. The 
dishwasher is equipped with an...