Smeg Blv2ne 1 Instruction Manual
Have a look at the manual Smeg Blv2ne 1 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions 9 3. Description of the controls 3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off etc. procedures are only possible when the door is open. 1 ON/OFF BUTTON Pressing this button energises the appliance. 2 SELECTED PROGRAM INDICATOR LIGHTS Illumination of this light denotes the program selected and the occurrence of a fault (troubleshooting). 3 PROGRAM SELECTION BUTTON By pressing this button in sequence it is possible to select the desired program. 4 WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT The light flashes to indicate that the appliance is in “water hardness adjustment” mode. SALT WARNIN LIGHT (on some models only) If the symbol is present, illumination of this light denotes a regenerating salt warning level. 5 RINSE AID WARNING LIGHT (on some models only) Illumination of this light signals that rinse aid dispenser is empty. 6 QUICK TIME + EXTRA OPTION BUTTON (see “EXTRA OPTIONS” section) The button controls selection of the quick time programs. (see table). 7 QUICK TIME PROGRAM LIGHT Illuminates to indicate that one of the extra programs (see table) is going to be executed.
User instructions 10 8 ENERSAVE OPTION + EXTRA OPTION BUTTON (see “EXTRA OPTIONS” section) Press the button to enable/disable the option. 9 ENERSAVE OPTION LIGHT Illuminates to indicate that the function is activated. 10 HALF LOAD BUTTON Press this button to activate the half load wash option. 11 HALF LOAD LIGHT Illuminates to indicate that the function is activated. 12 Flexi Tabs OPTION (EXTRA OPTION) LIGHT Illuminates to indicate that the function is activated. 13 PROGRAM DELAY BUTTON Press this button to delay the start of the program. 14 INFORMATION DISPLAY N.B.: symbols and styling are guideline and may vary depending on the model or version of the dishwasher purchased. SETTING THE WASHING PROGRAM AND SWITCHING ON To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling. After using the table to identify the most appropriate washing program: • press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; • keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desired program illuminates; • close the door; after about 2 the program will start. While it is in progress, the relative LIGHT will flash (indicating that the program is being executed).
User instructions 11 PROGRAMME, NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTES (1) WATER LITRES POWER KWh (1) 1 SOAK Pans and dishes awaiting completion of the load. Cold prewash 15 3,5 0,02 2 LIGHT Delicate dishes with normal dirt. Wash at 45°C Cold rinse Rinse at 70°C Dry 65 9,5 1,10 3 ECO (*) EN 50242 Dishes with normal dirt, even with dried-on residues. Cold prewash Wash at 50°C Cold rinse Rinse at 70°C Dry ** ** ** 4 AUTO 60-70 IEC/DIN *** Pans and dishes with normal dirt, even with dried-on residues. When the AUTO program is selected, the dishwasher recognises the type of dirt and automatically adjusts the washing parameters as appropriate. 5 SUPER **** Very dirty pans and dishes, even with dried-on residues. Hot prewash Wash at 70°C Cold rinse (2) Rinse at 70°C Dry 155 15,5 1,60 IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. The washing cycle will not take place if the dishwasher door is left open or not properly closed.
User instructions 12 QUICK TIME PROGRAMS (see relevant section for explanation of functioning modes) PROGRAMME NUMBER E SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTI (1) WATER LITRES POWER KWh (1) 6 RAPID 27’ + Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27 6,5 0,70 7 ECO QUICK + Dishes with normal dirt, washed immediately after use. Cold prewash Wash at 55°C Cold rinse Rinse at 70°C 80 12,5 1,25 8 NORMAL QUICK + Dishes with normal dirt, washed immediately after use. Cold prewash Wash at 70°C Cold rinse Rinse at 70°C 85 13 1,40 9 STRONG and FAST + Mixed dishes with normal dirt without dried-on residues. Wash at 65°C Cold rinse Rinse at 70°C 55 9,5 1,35 IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. The washing cycle will not take place if the dishwasher door is left open or not properly closed.
User instructions
13
NOTES AND REFERENCES Only run the soak program with half loads. Options cannot be used with the soak program. The ENERSAVE option (if featured) cannot be used with soak, ultra clean, or any
programs which do not include the final drying stage.
* Standard programme under EN 50242. If present, the ENERSAVE option must
be enabled.
** See information sheet provided
*** IEC/DIN reference programme. If present, the ENERSAVE option must be
enabled.
**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in the
door or tablet. Configuration: see photo in “Using the baskets”.
(1) The cycle duration and power consumption may vary according to the water and
room temperatures, and the type and amount of dishes.
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
- Annual energy consumption is based on 280 standard wash cycles with
cold water and consumption of low-energy operating modes. Actual
consumption depends on the way in which the appliance is used.
- Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the appliance is used.
- Information refers to the EN 50242 STANDARD programme (identified in the
programmes table), which is the most effective in terms of combined energy
and water consumption. The programme is recommended for dishes with a
normal level of dirt.
- Energy consumption in “sleep” mode = 0.02 W.
- Energy consumption in “on” mode = 1.5 W.
- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions 14 3.2 Washing programs Before starting a washing program make sure that: • The water supply tap is open. • The correct amount of detergent has been added to the dispenser. • The baskets have been correctly loaded. • The spray arms are able to rotate freely and without obstruction. • The dishwasher door is securely closed. QUICK TIME PROGRAMS Select this option together with any washing program (except the soak program) to SHORTEN the cycle by from a minimum of 10% to a maximum of 55%, depending on the cycle selected. To activate this option, press the QUICK OPTION button (light comes on) after selecting the program required. The option is automatically deactivated at the end of the program. ENERSAVE This option can be selected with the wash programme of choice to further reduce energy consumption. Drying is aided by a special device that automatically releases the door, which opens slowly and smoothly by a few centimetres. This ensures perfect drying and greater control of rinsing temperatures, which can be kept at lower levels for significant energy saving. Once the door has opened, the dishwasher emits a short beep and programme lights nos. 4 and 5 (marked “end”) flash to indicate the end of the washing cycle. Enersave is activated automatically every time a wash cycle is selected (except for programs that do not include the final drying phase; see programs table) and can be disabled before the program is started. When the function is activated, opening of the door must not be impeded in any way; do not leave anything in the space in front of the door necessary to allow it to open. Do not re-close the door during automatic opening as this would damage the mechanism. Wait for the pushers to retract before re-closing the door.
User instructions 15 SPREAD HALF LOAD Suitable when there are not many dishes to be washed, it saves energy and reduces the program duration. Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load. EXTRA OPTIONS - “Flexi Tabs” BUTTON Press buttons 6 + 8 (QUICK TIME PROGRAMS button + ENERSAVE option button) simultaneously to activate the Flexi Tabs option; the respective light comes on to confirm the selection. The option is optimised for use of detergents which are complete with salt and rinse aid, known on the market as 3 in 1, triple action, etc. With this option activated, any salt and rinse aid If you wish to use detergents which already contain salt and rinse aid already in the dishwasher will not be used. N.B.: even with the Flexi Tabs option selected, the regenerating salt/rinse aid lights will still stay on if their containers are empty. IMPORTANT: the option continues to be active until it is deactivated by pressing buttons 6 + 8 simultaneously; the light will then go out. If the water hardness has been set on a value above H3, and the “Flexi Tbas” option is activated, the relative light flashes, warning of a setting error. Multi-function products are not suitable for use with very hard water; this does not prevent the use of the option, but the washing results might not be of the best. DELAYED START The start of the washing program can be delayed to program the dishwasher to operate at the preferred time of day (e.g. overnight). Press the PROGRAM DELAY button to activate the option and display a 1 hour delay. Keep pressing to select the delay required, which may be up to 9, 12 or 24 hours depending on the model. When the door is closed, the appliance will prewash the dishes, after which the program delay set will come into effect.
User instructions 16 CANCELLING THE CURRENT PROGRAM • To cancel the currently selected program, open the door and hold down the PROGRAM SELECTION (3) button for a few seconds until the indicator lights for programs 4 and 5 illuminate simultaneously (the word end is displayed on the window). • Close the door. • After approximately 1 minute the dishwasher will advance to the end of cycle. CHANGING THE PROGRAM To change the program in progress, simply open the door and select a new program. When the door is closed the dishwasher will automatically select the new program.
User instructions 17 TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT • Always try to run the dishwasher fully loaded. • Do not wash the dishes in running water. • Use the washing program that is most appropriate for each type of load. • Do not carry out any preliminary rinsing. • If available, connect the dishwasher to a hot water supply up to 60°C. • Use the ENERSAVE option. TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: • separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; • do not pour the detergent directly on the dishes. If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program. END OF CYCLE At the end of the washing cycle the dishwasher gives a short acustic signal and the program indicators nr 4 and 5 start blinking (the word end is displayed on the window). To switch off the dishwasher, open the door and press the ON/OFF button (1). REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket.
User instructions 18 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: • Adjust the water softening system; • Add the regenerating salt; • Add the rinse aid and detergent. 4.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF – 24-31°dH). When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1.7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. • When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. • Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated. • Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. SALT