Smeg Blv1r 1 Instruction Manual
Have a look at the manual Smeg Blv1r 1 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions
30
ADJUSTING THE UPPER BASKET
Version A:
the upper basket can be adjusted in two positions,
according to the user’s needs and according to the height of the dishes
in the lower basket. Proceed as follows:
• pull out the right-hand basket guide;
• remove the stop, first releasing it as shown in the diagram;
• push the guide to free the wheels;
• fit the upper or lower pair of whee ls into the guide, depending on the
setting required
;
• return the stop to its original position.
Version B:
• pull out the basket to its limit position and pull the right side
upwards. At this point it is possibl e to load larger sized plates into
the lower basket.
• To return to the original position, pull out the upper basket again and press the release lever.
User instructions 31 Version C: the top basket can be set in three different positions on both sides. The rack must be level on both sides. To raise the basket lift it, pulling on the front edge (1), to the first or second catch depending on the height required. To lower it, pull the release lever (2) . This is also possible with the basket loaded, but in this case when lowering the basket it should be held steady with one hand to avoid knocking the dishes.
User instructions
32
5. Cleaning and maintenance
Before carrying out any work, a lways unplug the appliance from the
electrical supply or switch off the all-pole disconnection device.
5.1 General warnings and recommendations Avoid the use of acidic or abrasive detergents. Clean the outer surfaces and door-lining of the dishwasher regularly
using a soft cloth moistened with water or with a normal detergent
suitable for painted surfaces. Clean the door gaskets with a damp
sponge. Periodically (once or twice a year) it is advisable to clean the
tank and gaskets, using a soft cloth and water to remove any deposits.
CLEANING THE WATER INTAKE FILTER
The water intake filter
A located at the outlet of the water supply tap
needs to be cleaned periodically.
After having closed the water supply tap, unscrew the end of the water
intake hose, remove the filter A and clean it delicately under running
water. Reassemble filter A in its seat and carefully screw the water
intake hose back into position.
CLEANING THE SPRAY ARMS
The spray arms can be easily removed for periodic cleaning of the
nozzles, to prevent possible clogging. Wash them under running water
and carefully replace t
hem in their seats, checking that their rotary
movement is in no way impeded .
• To remove the upper spray arm, unscrew locking ring R.
• To remove the lower spray arm, simply lift it up, pulling by the
central part.
• To remove the orbital spray arm assembly, take hold of the longer
arm and pull the orbital unit upward. Wash the arms under a jet of
running water and return them carefully to their seat. After
reassembly, check that the spray arms turn freely. Otherwise,
check that they have been installed correctly.
ORBITAL
User instructions 33 CLEANING THE FILTER UNIT • It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards; • push the centre filter D from the underside to remove it from the micro-filter: • separate the two parts which make up the plastic filter by pressing the body of the filter in t he zone shown by the arrows; • remove the centre filter by lifting it upwards. GENERAL WARNINGS AND RE COMMENDATIONS FOR CORRECT MAINTENANCE: • The filters should be cleaned under running water using a stiff brush. • When removing the filter , take care that there are no food residues on it. If any residues fall into the washing pit they might block hydraulic components, or f oul the spray arm nozzles. • It is essential to thoroughly clean the filters according to the above instructions: the dishwasher ca nnot function if the filters are clogged. • Carefully replace the filters in their seats, to avoid damaging the wash pump. PROLONGED DISUSE: • Run the soak program twice in succession. • Unplug the power cord from the socket. • Leave the door slightly open , in order to prevent the formation of unpleasant odours inside the washing tank. • Fill the rinse aid dispenser . • Shut off the water supply tap.
User instructions 34 BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE: • Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes. • Plug the power cord back into the socket. • Reconnect the water intake hose and open the tap again. TROUBLESHOOTING MINOR PROBLEMS In some cases it is possible to remedy minor problems by referring to the following instructions: If the program fails to start, check that: • the dishwasher is connected to the electrical power supply; • there is no power failure; • the water tap is open; • the dishwasher door is properly closed. If water remains inside the dishwasher, check that: • the drain hose is not kinked; • the drain siphon is not obstructed; • the dishwasher filt ers are not clogged. If the dishes are not being cleaned properly, check that: • the correct amount of det ergent has been added; • there is regenerating salt in side the special container; • the dishes are being loaded correctly; • the selected program is suitable for the dish types and their degree of soiling; • all the filters are clean and positioned correctly; • the spray arm nozzles are not obstructed; • there is no object obstructing the rotation of the spray arms.
User instructions 35 If the dishes fail to dry or remain dull, check that: • there is rinse aid inside the special container; • the rinse aid dispenser setting is correct; • the detergent used is of good quality and has not lost its effectiveness (for example, throu gh incorrect storage, with the box left open). If the dishes show signs of streaking, staining, etc., check that: • the rinse aid dispenser setting is not too high. If there are visible traces of rust inside the tank: • the tank is made of st eel, and therefore any rust marks are due to external elements (fragments of rust from the water pipes, pots, cutlery, etc.). Special products ar e commercially available to remove such marks; • check that the amount of deter gent being used is correct. Certain detergents can be more corrosive than others. • check that the cap of the salt cont ainer is securely closed, and that the water softening setting is correct. If after following the above troubles hooting instructions the problem persists, call the nearest After-Sales Centre. WARNING: any operations perfo rmed on the appliance by unauthorised persons are not covered by the warranty and shall be paid for by the user.
User instructions 36 6. Troubleshooting The dishwasher is capable of signall ing a number of faults through the simultaneous illumination of several i ndicator lights, with the following meanings: FAULT DESCRIPTION E1 Acquastop failure The anti-flooding system has been activated (for the relevant models only). The system is tripped in case of water leaks. Contact the after-sales service. E2 Safety level The system which limits the water level inside the dishwasher has been tripped. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. E3 Water heating malfunction The water is not heated or the heating parameters are not correct. Repeat the washing program; if the problem persists, contact the after-sales service. E4 Water temperature monitoring malfunction Interrupt the program and switch off the dishwasher. Switch the dishwasher ba ck on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. E5 Water intake malfunction The appliance does not take in water or does not do so correctly. Check that the water connections are correct, the water intake tap is turned on and the filter is not fouled. If the probl em persists, contact the after-sales service. E6 Water pump-out malfunction The appliance does not pump out the water or does not do so correctly. Check that the drain hose is not kinked or crushed and that the siphon and filter are not fouled. If the problem persists, contact the after- sales service.
User instructions 37 FAULT DESCRIPTION E7 Turbine flow-regulator malfunction (for the relevant models only) The appliance is not able to measure the amount of water loaded accurately. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. E8 Alternate washing system malfunction Interrupt the program and switch off the dishwasher. Switch the dishwasher ba ck on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. E9 Water intake system malfunction Contact the after-sales service. Light off Light on Light flashing If an alarm occurs the appliance interrupts the program in progress and signals a fault. • Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately. • The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program. • The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed. To “reset” an alarm is necessary: • Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again. If the malfunction persists, contact your authorised Service Centre.
User instructions 38 TECHNICAL DATA Width 600 mm Depth measured flush with the outer edge of the control panel Free standing: 600 mm Semi-integrated: 584 mm Height Free standing: from 885 mm to 905 mm Semi-integrated: from 818 mm to 868 mm Capacity 14 Standard place settings Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) Electrical characteristics See rating plate