Smeg A1pyid7 Manual

							Instructions for the user
89
10.2 Removing the door
Open the door completely.
Insert two pins into the holes on the hinges
towards the back of them until they engage.
Grasp the door on both sides with both hands,
lift it forming an angle of around 30° and
remove it.
To reassemble the door, put the hinges in the
relevant slots in the oven, making sure that
grooved sections C are resting completely in
the slots.  Lower the door and once it is in place
remove the pins from the holes in the hinges. 
						

							Instructions for the installer
90
11.INSTALLING THE APPLIANCE
11.1 Installing in kitchen units
Veneers, adhesives or plastic coatings on adjacent furniture should be
temperature-resistant (no less than 90°C). If they are not sufficiently
temperature-resistant, they may warp over time. 
The appliance must be installed by a qualified technician and according to the
regulations in force.
Depending on the type of installation, this appliance belongs to class 2,
subclass 1 (Fig. A - Fig. B) or to class 1 (Fig. C).
It may be installed next to walls, one of which must be higher than the worktop,
at a minimum distance of 50 mm from the side of the appliance, as shown in
figures A and C relative to the installation classes.
Make sure that there is a minimum distance of 750 mm between the stoves of
the hob and any shelf that may be installed directly above it. If a hood is installed
above the hob, refer to the hood instruction manual to ensure the correct
clearance is left.
Built-in appliance (Class 2 subclass 1)
Built-in appliance (Class 2 subclass 1)
Free-standing appliance (Class 1) 
						

							Instructions for the installer
91
11.2 Electrical connection
Make sure the voltage and the cross-section of the power supply line match the
specifications indicated on the identification plate positioned on the appliance.
Do not remove this plate for any reason. A copy of the plate is attached to the
instructions.
The appliance must be connected to the power supply by a qualified technician.
Before performing any operations, switch off the power supply to the appliance.
The appliance must be connected to earth in compliance with electrical system
safety standards.
Where the appliance is connected to the power grid via plug and socket, both of
these must be of the same type and connected to the power cable in
accordance with current standards. The socket must be accessible after the
appliance has been built in. 
NEVER UNPLUG BY PULLING ON THE CABLE.
Should the earthing wire need replacing it must be longer than the conducting
wires so that, if the plug is torn off the power cable, it is the last to be detached.
Avoid use of adapters and shunts as these could cause overheating and a risk
of burns.
If a fixed connection is being used, fit the power line with an omnipolar circuit
breaker with a contact opening gap equal to or greater than 3 mm, in an easily
accessible position close to the appliance.
The manufacturer declines all responsibility for damage to persons or things
caused by non-observance of the above prescriptions or by interference with
any part of the appliance. 
						

							Instructions for the installer
92
POSSIBLE 
CONNECTION TYPESCABLE TYPE
(if not present)
380 - 415 V 3N~5-pole5 x 2.5 mm² H05V2V2-F
380 - 415 V 2N~4-pole4 x 4 mm² H05V2V2-F
220 - 240 V 1N~3-pole3 x 6 mm² H05V2V2-F
•  Use H05V2V2-F cables withstanding temperatures of 90°C or higher.
•  The values indicated above refer to the cross-section of the internal
conductor.
•  The tightening torque of the screws of the terminal supply wires must be 1.5
- 2 Nm.
The aforementioned power cables are sized taking into account the coincidence
factor (in compliance with standard EN 60335-2-6). 
						

							Instructions for the installer
93
11.3 Positioning the skirt
WARNING: The skirt provided is an integral part of the product; it must be
fastened to the appliance prior to installation.
•  Position the skirt above the top, taking care
to align holes A with holes B.
•  Secure the skirt to the top by tightening
screws C.
11.4 Positioning and levelling the appliance
After making the electrical and/or gas connections, properly level
the appliance on the floor to ensure better stability. Screw or
unscrew the bottom part of the foot until the appliance is stable and
level on the floor. 
						

							Instructions for the installer
94
11.5 Wall mounting instructions  (some markets only)
1 Fasten a hook bolt (not supplied) into the wall at
a height (h) of 800 mm from the floor.
The installer must provide the hook bolt when installing the appliance.
2 Attach the snap hook to the chain.
3 Attach the end of the chain to the hook bolt
fastened in the wall.
4 Finally, connect the snap hook to the appropriate
hole on the back of the appliance.