Sim2 Multimedia Projector Nero 3d 2 User Manual

							Connections
❶ ❷ ❸ ❹ ❺ ❻
❼ ❽
Inputs ❶
HDMI 1
HDMI 2 Accept both HDMI and DVI  digital video inputs.
❷
Components/RGB-HV Four RCA connectors. They accept both standard  
and high-definition component (YPrPb) and  
RGB - HV signals. Also used as RGB input for SCART  
RGBS signals.
❸
Video One RCA connector. Accepts composite video sig -
nals. Also used as composite sync input for SCART  
RGBS signals.
❹
Graphics RGB One  D-Sub 15 - pin female  connector. Accepts  
component or RGB high-definition signals.
Control/
Service ❺
USB USB 1.1 (type B) port for serial commands and  
firmware upgrade.
❻
RS-232 RS232 (female D-Sub 9 - pin) port for serial  
commands and firmware upgrade.
Outputs ❼
TRIG 1 12 V 100 mA max output, for motorized screen  
control. Activates when the projector is switched  
on.
TRIG 2 12 V 100 mA max output, for motorized screen  
masking systems control. See “ Screen ”  on page  
27 .
TRIG 3 12 V 100 mA max output, for motorized ana -
morphic lens position control. See “ Anamorphic
Lens ”  on page  27 .
❽
3D Sync OUT VESA DIN - 3 connector for 3D IR Emitter cable.
2    Overview Nero 3D
User Guide 11 
						

							3D IR Emitter
The 3D infrared emitter is designed to be placed near the projector and aimed at the  
screen. It receives the 3D sync signal from the projector and emits infrared pulses that  
bounce off the screen and the walls to reach the 3D glasses infrared receiver.
Note:   The emitter emits sync pulses only when the projector displays 3D content.
3D Glasses
When displaying 3D content, the projector alternately displays one image for the left  
eye and one image for the right eye in rapid succession. The 3D glasses turn on and off  
their lenses, in sync with the projector, so that each eye receives exactly the image in -
tended for it. The sync is possible thanks to the infrared pulses received by the glasses  
from the 3D IR emitter.
❶ ❷
❸ ❹ ❺
❶
Indicator light Indicates glasses status
❷
Battery compartment For CR2032 (3 V DC / 0.2 A) batteries
❸
IR receiver Receives infrared signals from the 3D Emitter
❹
Lens Liquid crystal shutter
❺
Button Button for on and off
2    Overview Nero 3D
User Guide 12 
						

							3 Installation
This section provides instructions for the installation of the  Nero 3D  projector.
Important:  Installation procedures should be performed by a qualified AV system spe -
cialist.
Location
When installing the  Nero 3D  projector, take the following considerations into account.
Installation Type
Select the installation type that best suits your needs:
• front or rear projection
• floor or ceiling mount
Lens Type
Choose the desired distance from the screen and select the lens type (T1, T2 or T3)  
that determines the desired screen size.
Cooling
Make sure that the planned location for the projector has adequate ventilation. Check  
that room temperature is below 35° C and that the projector is away from heating  
vents. Ensure a minimum 0.25 m (10 in.) clearance on the left, right and rear sides of  
the projector.
Power Outlets
Verify that the powers outlets are grounded and preferably shielded from power  
surges and fluctuations. A UPS is optional.  Nero 3D  power supply operates on any  
nominal line voltage between 100-240 V AC, 50-60 Hz.
Cables
Check planned cable lengths for video and control cables and make sure these lengths  
do not exceed specifications.
Ambient Light
Avoid or minimize light sources directed at the screen to preserve the quality of the  
projected image.
Mounting
The projector can be Floor mounted (upright) or Ceiling mounted (inverted). Choose  
the method that best suits your installation.
Important:  The projection lens is not centered to the chassis (it is off-center horizont -
ally by 75 mm or 2.95 in., see “ Dimensions ” on page  41  for details). Make sure the  
centerline of the lens is centered horizontally to the center of the screen.
Floor Mounting
Position the projector on a secure and flat surface (such as a table or a shelf). Adjust  
the three feet at the bottom of the projector until the projector is level on all sides.
3    Installation Nero 3D
User Guide 13 
						

							Ceiling Mounting
Invert the projector and suspend it from the ceiling using a specific bracket.
• To fit the bracket unscrew and remove the 3 rubber feet
• Attach bracket by using 3 x M6 screws not exceeding 15 mm in length
For ceiling mounting use only SIM2-approved ceiling brackets and adhere  
to the installation instructions and safety guidelines provided with the  
bracket. Do not over-tighten the screws.
Orientation
By default, the  Nero 3D  is configured for a Front installation (projector installed up -
right and in front of the screen). If the projector is installed behind the screen or inver -
ted, you can use the image orientation function of the projector (see “ Orientation ”  on  
page  29 )
Vertical Lens Shift
Ideally, the projector should be positioned at a right angle to the screen and in such a  
way that:
• the lens center and screen center are aligned with each other
• the projected image fills the screen perfectly
3    Installation Nero 3D
User Guide 14 
						

							If it is not possible to position the projector perpendicular to  
the projection screen (so that the lens center and screen cen -
ter are aligned with each other) you can use the mechanical  
lens control at the top of the projector to shift the projected  
image vertically:
• insert the provided hex wrench into the vertical lens  
shift adjuster
• turn the wrench to shift the lens in the desired direc -
tion
The  Nero 3D  provides up to 50% of vertical lens shift up. For example, with a 16:9 150  
in. diagonal size screen, you can shift the image up to 0.93 m (36.8 in.) above the  
screen center (see “ Projection Distances ”  on page  40 ).
Keystone
If the projector is ceiling-mounted and the screen is lower than the projector, you may  
need to tilt the projector by adjusting the ceiling mount. If you do so:
• the top and bottom borders of the image will be unequal in length
• the sides of the image will be inclined
If the tilt is not excessive, you can use the Keystone function of the projector to cor -
rect the image shape. See “ Keystone ”  on page  29 .
Note:  Keystone correction may cause artifacts in the image and may not be available  
when displaying specific 3D content (see  Table 4.2 ).
Zoom and Focus
The  Nero 3D  provides motorized Zoom and Focus controls. You can access these  
adjustments through the remote control directly:
• F1  key for optical Zoom
• F2  key for Focus
See “ F1-F2 Keys ”  on page  31  for details.
Connections
Proceed as follows to connect the  Nero 3D  to video sources, control devices, screen  
control systems, 3D sync emitter and AC power.
When connecting your equipment:
• turn off all equipment before making any connections
• use the correct signal cables for each source
• make sure cables are routed so that people are not impeded or become a trip  
hazard
• ensure that the cables are securely connected (tighten the thumbscrews on  
connectors that have them)
Video
Often the sources (Blu - ray Players, Set Top Boxes, Game Consoles and so on) have sev -
eral outputs. Choose HDMI whenever possible.
• HDMI  The major benefits of this signal type are:
◦ best image quality, because the signal is carried in the digital domain  
3    Installation Nero 3D
User Guide 15 
						

							throughout the entire signal path
◦ highest available resolution, because video sources can deliver full resolu -
tion content via HDMI only
◦ availability of 3D content, because most 3D compatible sources deliver 3D  
content from HDMI only
◦ optimization of several image parameters (2D/3D content, color space, as -
pect, signal range, over scan), thanks to auxiliary information (AVI in -
foframe) sent by the source device together with the signal.
If your source has dual HDMI outputs, we would recommend direct connec -
tion to the projector from one of the HDMI connections and the second HDMI  
output to the input of an appropriate AV receiver/processor for audio.
Sources with a DVI-D output can be connected to the HDMI input of the pro -
jector using a suitable DVI-D to HDMI cable. In this case no auxiliary informa -
tion is sent from the source to the projector.
Note:  HDMI uses a code known as HDCP (High-bandwidth Digital Copy Protec -
tio n), which protects the recorded supports from being copied illegally. The  
connection between the source and display require that the two devices per -
form a handshake and exchange code keys before being able to display an im -
age. The InstaPort technology allows a simultaneous pre-authentification of  
every attached device at the same it is connected, reducing drastically the  
time required for HDMI source switching. For this reason you may note a  
slight delay before the image appears on the screen, but it is perfectly normal.
• Graphics RGB  Input for Personal Computer and other sources that outputs  
RGB or YPrPb signals. These sources must be able to provide separate H/V  
sync or composite H+V sync.
• RGB/YPrPb   Input for DVD Players, Set Top Boxes and other sources that  
output one of the following signals:
◦ Component (YPrPb)
◦ RGB with composite sync on green (RGsB)
◦ RGB with HV composite sync
RGB connectors also provides RGB input for SCART RGBS sources. See “ Video ”  
below and “ RGBS Sync ”  on page  30 .
• Video  This is the the input for composite video sources (such as VCR or  
camcorders). This connector is also the composite sync input for SCART RGBS  
sources. See “ RGB/YPrPb ”  above and “ RGBS Sync ”  on page  30 .
Control
You can connect the  Nero 3D  projector to a Personal Computer or a control system  
through one of the following methods:
• RS-232 port, using a standard 9-pin straight serial cable
• RS-232 port, using a USB to serial converter cable. In this case, installation of a  
device driver provided by the cable manufacturer may be required
• USB port, using a USB Type A (rectangular) to Type B (square) cable connector.  
In this case, installation of a device driver provided by SIM2 may be required –  
ask your SIM2 Authorized Dealer
3    Installation Nero 3D
User Guide 16 
						

							Note:  RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to  
5   m (16 ft.).
Triggers
Some Home Theater devices can be controlled through a 12 V signal. The projector  
can output three 12 V (100 mA max) signals:
• TRIG1 for motorized screens control
• TRIG2 and TRIG3 are for motorized screen masks and anamorphic lens motors  
control. See “ Screen ”  and “ Anamorphic Lens ”  on page  27  for instructions on  
how to do configure them from OSD
Note:  Three jack adapters are shipped with the projector.
IR Emitter
The IR emitter sends the infrared pulses that sync the 3D glasses. Proceed as follows  
to install the emitter:
1. place the emitter near the projector on a secure surface or use an appropriate  
mount kit
2. connect the supplied 3D IR emitter to the projector  3D Sync Out  output
3D Glasses
The glasses are shipped with the battery already inserted in its compartment:
1. Remove the battery insulating sheet by pulling it. As a result of this, the  
glasses turn on.
2. Press the button once (for less than 1 second) to turn them off. You will see  
the indicator light ramp from bright to off.
For more information on glasses status and transitions, refer to “ 3D Glasses ”  on page  
20 .
To install the battery:
1. Open the battery cover.
2. Insert one CR2032 battery making sure the polarity match the mark inside the  
battery cover.
3. Replace the cover.
Replace the battery with a new one when the glasses fail to work prop -
erly. Dispose of used battery according to local regulations. Keep away  
from children.
AC Power
Choose the AC power cord that is appropriate in your area among those shipped with  
the product. Plug the female end of the power cord to the AC receptacle located on  
the right hand side of the projector (100-240 V AC, 50-60 Hz) and the other end into a  
grounded AC outlet. An high-quality surge protector is recommended while a UPS is  
optional.
3    Installation Nero 3D
User Guide 17 
						

							Switching On and Off
Switching On
1. Turn on the main power switch on the right hand side of the projector. The  
projector enters the low power Standby status. The indicator light on the left  
hand side of the projector turns red and the status display next to it shows  . .
2. Press any of the numeric keys ( 0 - 9 ) on the remote control or the  I/O  button  
on the projector keypad to switch on the projector.
3. The indicator light turns green and red and the status display shows  88  for a  
while.
4. When the projector is ready for use an image appears on screen (this can take  
approximately one minute).
5. If a valid signal is detected, an image appears on the screen, otherwise a black  
screen with a “No Signal ”  message is displayed.
Switching Off
1. Press and hold the  Off  key on the remote control or the  I/O  button on the  
projector keypad.
The indicator light flashes green and red to indicate that the projector is cool -
ing down. Cooling fans remain on for approximately four minutes to cool the  
lamp. In the meanwhile the projector cannot be turned on again.
2. After cooling is complete the projector enters Standby status. The indicator  
light turns solid red and the status display turns black, unless an error or  
warning code is displayed.
Warning:   Wait for the cooling fans to turn off before turning off the main power  
switch or unplugging the projector.
3    Installation Nero 3D
User Guide 18 
						

							4 Operation
Viewing 3D Content
3D stereo visualization offers clear and sharp 3D images thanks to 3 chip DLP Imaging  
technology. This technique achieves channel separation using active shutter glasses.
• Active shutter glasses turn on and off in rapid succession and stop light reach -
ing your eyes. The glasses are synced using a IR emitter connected to the pro -
jector.
• When an image is destined for the left eye, the right lens of the glasses goes  
dark preventing any of the image for your left eye from reaching the right eye.  
The left lens is completely open.
• The process repeats very quickly (up to  120  times per second) for each eye.
• The human brain combines the two images and creates the illusion of 3D.
Important:  Read 3D safety information at the beginning of this User  Guide  before  
viewing 3D content.
Your  Nero 3D  projector is capable of displaying 3D Images of exceptional high quality;  
to ensure maximum enjoyment and trouble free viewing we recommend the following  
guidelines.
• You will need a Blu - r ay player or equivalent that is capable of play -
ing 3D content and is HDMI 1.4 compliant plus of course a copy of  
a film that has released on Blu - r ay in 3D. Only films with the 3D logo are com -
patible.
• Ensure your player has the latest software installed.
• If your Blu - ray Player has dual HDMI outputs, we would recommend direct  
connection to the projector from one of the HDMI connections and the  
second HDMI output to the input of an appropriate AV receiver/processor for  
audio.
• If you are routing all of your HDMI sources through an AV receiver/processor  
the product must be 3D compatible and HDMI 1.4 compliant. Ensure your  
equipment has the latest firmware installed (refer to the manufacturer for fur -
ther information).
• Other 3D content providers are available such as Satellite Broadcasters, Cable  
providers, VOD and Streaming services, gaming consoles such as PlaySta -
tion   3. Details of the 3D service provided can be obtained by contacting your  
local/regional operators.
To watch 3D Content via  Blu - ray
• Switch on the Nero 3D and all other relevant products such as Blu - ray player  
and AV receiver and ensure the correct inputs have been selected.
• Insert your 3D Blu - r ay disc and press play, follow the on-screen menus.
Note:  Some discs contain both the 3D and 2D versions of the film, ensure you  
select the correct one.
4    Operation Nero 3D
User Guide 19 
						

							• Switch on your 3D glasses. Refer to the instructions supplied with the glasses  
to ensure correct operation.
• The projector will automatically detect the 3D signal and you will be prompted  
to wear your glasses via the OSD.
To Watch 3D Content via Satellite, Cable and Games Console
• Switch on the Nero 3D and all other relevant products such as Satellite  
receiver and AV receiver and ensure the correct inputs have been selected.
• Select the appropriate 3D channel.
• If the projector displays two distorted images side by side or one on top of  
each other, select the 3D menu by pressing    II   on the remote control.
• Select 3D mode via the OSD (this will expand the menu). Select the correct  
version of the 3D format using the up/down/left/right keys.
• Switch on your 3D glasses. Refer to the instructions supplied with the glasses  
to ensure correct operation.
Important:  All 3D technologies currently available today filter out a large amount of  
light. Therefore it is perfectly normal for the 3D image to be noticeably dimmer when  
compared to the picture in 2D mode. Adjust the 3D picture and lamp settings accord -
ingly for 3D viewing.
3D Glasses
Follow the simple instructions below to operate your 3D glasses:
• On  Press the button once (see “ 3D Glasses ”  on page  12 ). You will see the  
indicator light ramp from off to bright, and then turn off again. You are now in  
SIM2 Cinema mode and the glasses and the projector are synced. If, for any  
reason, the glasses behave differently, reset them (see below).
• Off  Press the button once. You will see the indicator light ramp from bright to  
off.
Note:  Glasses will turn themselves off after a few minutes without the sync  
signal.
• Reset    In the unlikely event that you need to reset your glasses, remove the  
battery from its compartment, and then replace it.
Note:  For battery replacement refer to “ 3D Glasses ”  on page  17 .
3D Menu
To view 3D content additional adjustments are required. With 3D content playing,  
press   II  o n the remote to access the OSD  3D  menu.
3D Mode
• 3D  Activates 3D mode and the IR emitter will be activated. Automatic selec -
tion is determined by the source sending the projector the correct informa -
tion. If the incorrect 3D image is displayed after approximately 10 seconds go  
to the 3D Input Format and manually select the correct 3D mode for the in -
coming signal.
4    Operation Nero 3D
User Guide 20