Sim2 Multimedia Projector Ht380 User Manual

11
5   SwiTChiNg ThE PROJECTOR ON AND Off
wARNiNg: Connect the projector to a power supply with a 
nominal voltage within the following values: 110-240 V AC, 
50/60 hz. it must be earthed (f ig. 12).
Position I : on
Position O : off
Power switch
Fused power 
socket  Power plug
 
Fig. 12
In position i the projector will initialise itself  (red and green leds 
on) and then goes into standby mode (red led on) (Fig. 13).
HDMI AUDIO
OUT
ZOOM
CONTROL (RS 232) GRAPHICS RGB
R/Cr
G/Y
B/Cb
HV
2
435
ATTENTION: pour...

12
SwiTChiNg Off AND RETURNiNg TO STANDBY
With the remote control: press  .
With the keypad: press .
When switching off, the projector goes into stand-by mode and 
stores the input selection at the time of switch-off.
The  fans  keep  running  until  the  lamp  cools  down  (green  and 
red leds on), after which they automatically switch off. Do not 
switch off the projector with the power switch until the fans have 
stopped running.  
6  CONNECTiONS
To obtain the best performance from your projector, we...

13
hT380 - Connection panel 
31245
Television receiver
DVD player
VCR
Videocamera
Video game console
Television receiver
HDTV receiver
DVD player
VCR
Video game console
ComputerDVD player
HDTV receiver
Fig.16
6
HDMI AUDIO 
OUT 
ZOOM 
CONTROL (RS 232)  GRAPHICS RGB 
R/Cr 
G/Y 
B/Cb 
HV 
1 2 
4 3 5 
 
ATTENTION: pour ne pas compromettre 
la protection contre les resque dincende 
remplacer par un fusible de meme type 
et de mems caracteristique 
CAUTION: for continued protection against 
risk of fire,...

14
of the pictures reproduced by the D80 in the two cases:  the 
deinterlacing performed by the HT380 is often more effective 
than that performed by the source itself.
gRAPhiCS RgB
This input should be connected to an RGB-type video or graphic 
signal using a cable with a DB15HD type connector.
The signal source device (typically a personal computer or game 
console) must be able to provide separate H/V synchronisation or 
composite H+V synchronisation.
hDMi™
HDMI™  (High  Definition  Multimedia...

15
RS232 iNTERfACE CONNECTOR 
The projector can be controlled from a PC: simply hookup 
the interface connector to a PC ’s RS232 serial cable.
Do  not  place  objects  between  the  remote  control  and  the 
receiver on the projector, as this can prevent the remote from 
working.
MOTORiSED SCREEN OUTPUTS
12Volt
120 mA
 
The  projector  is  equipped  with  two  outputs  (Voltage:  12  Vdc) 
for motorised projection screen and screen masking systems, 
used for masking off the projection area to match the...

16
MAiN MENU
To  access  the  main  menu  of  the  On  Screen  Display  press 
the MENU key on the keypad or the MENU+ or MENU- key on the 
remote control. 
The  main  menu  is  divided  into  four  windows, PICTURE,  IMAGE, 
SETUP  and  MENU,  in  which  the  various  adjustments  are  grouped 
according to the frequency of use. Use the ▲ and ▼ keys to 
select  the  line  corresponding  to  the  adjustment  you  wish  to 
make (Fig. 21). 
The  various  menus  only  offer  the  relevant  adjustments  in...

17
To  access  these  submenus,  press  the  

18
NORMAL:  projects  the  image  occupying  the  full  height  of  the 
screen  while  maintaining  the  aspect  ratio  of  the  input  signal. 
When the input signal aspect ratio is 4:3 black vertical bands 
are displayed on the right and left of the picture.
ANAMORPHIC: correctly displays a 16:9 image.
LETTERBO x: serves to display a 4:3 letterbox image (with source 
signal having black bands above and below the picture) so that 
it fills the 16:9 screen and maintains the correct aspect ratio....

19
gAMMA CORRECTiONDetermines the system’s response to the grey scale, empha-sising or attenuating the different grades of brightness (blacks, dark, medium, light grey, whites) in the projected image. The projector has a range of gamma functions which enable you  to  display  any  image  to  the  best  effect  for  the  type  of video  source,  the  ambient  lighting  and  your  subjective  pre-ferences.There  are  4  sets  of  gamma  curves:  Standard  (ST),  Enhanced 
 ST1  For general use
 ST2
 ST3...

20
SIM2 (EN) and Graphics (GR), User. The Standard curve has been defined  for  general  use,  and  is  set  for  videocameras,  digital cameras, and for viewing films or photos on your PC. The Enhan-ced set is suitable for watching movies. The Graphics set is suited to  displaying  synthetic  graphics  (PC,  CAD,  PC  presentations, etc.). User enables you to define your own curve. You can thus select the coefficient which determines the curve.  Values from 1.5 to 2.2 allow you to emphasise the detail...