Sim2 Multimedia Ht3000 E Projector User Manual

11
ht3000e
5   SwiTChiNg ThE PROJECTOR ON AND Off
wARNiNg: Connect the projector to a power supply with a 
nominal voltage within the following values: 100-240 V AC, 
50/60 hz. it must be earthed (f ig. 12).
GRAPHICS RGBHV
S-VIDEO
AUDIO OUT
HDMI 1
REMOTE2 S-VIDEO
MENUESC
INPUT1 
5 
4 
0 
I 
Power Switch:
Position I: On
Position 0: Off
Fused
Power Socket
     
Power Plug
 
Fig. 12
In position  i the projector will initialise itself  (red and green leds 
on) and then goes into standby mode (red led on)...

12
ht3000e
Initialisation 
Status Led blueLed red
Standby 
On 
Cooling 
: Of : On
: Flashing
Error (*)
Logo Backlit 
Blue Color
Red Color
Of / Blue Color 
(*)
Red Color
Red Color 
SwiTChiNg Off AND RETURNiNg TO STANDBY
With the remote control: press  .
With the keypad: press .
When switching off, the projector goes into stand-by mode and 
stores the input selection at the time of switch-off.
The  fans  keep  running  until  the  lamp  cools  down  (green  and 
red leds on), after which they automatically...

13
ht3000e
hT3000E - Connection panel 
31245
Television receiver
DVD player
VCR
Videocamera
Video game console
Television receiver
HDTV receiver
DVD player
VCR
Video game console
ComputerDVD player
HDTV receiver
Fig.16
6
+12V
USB 1. 1 R/Pr
CONTROL (RS232 )
GRAPHICS RG B
C/
Y B
/P b 
HV S
-VIDEO
AUDIO O UT
HDMI 1
REM OTE
3 
2 S-VID EO
MEN U ESC
S
OURC E
1 
 4 
 O 
I 
 
1 VIDEO 
GRAPHICS RGB 
4 
3 RGB - YPrPb 
HDMI 
5 
HDMI 
6 
5 
2 S-VIDEO
H
DM I 26   

14
ht3000e
of the pictures reproduced by the HT3000E in the two cases:  
the  deinterlacing  performed  by  the HT3000E  is  often  more 
effective than that performed by the source itself.
gRAPhiCS RgB / YPrPb
This input should be connected to an RGB-type or YPrPb-type 
video signal using a cable with a DB15HD type connector.
Using  RGB-type  signal,  your  source  device  must  be  able  to 
provide separate H/V synchronisation, composite H+V synchro-
nisation or composite synchronisation on green...

15
ht3000e
RS232 iNTERfACE CONNECTOR 
The projector can be controlled from a PC: simply hookup 
the interface connector to a PC ’s RS232 serial cable or to a 
PC's USB 1.1 cable.
Do  not  place  objects  between  the  remote  control  and  the 
receiver on the projector, as this can prevent the remote from 
working.
MOTORiSED SCREEN OUTPUTS
+12V
USB 1.1 R/Cr
               RS232 GRAPHICS RGB
C/Y
B/Cb 
HV S-VIDEO
AUDIO OUT
HDMI 1
REMOTE
3 
2 S-VIDEO
MENU1 4 
12Volt
120 mA
 
The  projector  is...

16
ht3000e
MAiN MENU
To  access  the  main  menu  of  the  On  Screen  Display  press 
the MENU key on the keypad or the MENU+ or MENU- key on the 
remote control. 
The  main  menu  is  divided  into  four  windows, PICTURE,  IMAGE, 
SETUP  and  MENU,  in  which  the  various  adjustments  are  grouped 
according to the frequency of use. Use the ▲ and ▼ keys to 
select  the  line  corresponding  to  the  adjustment  you  wish  to 
make (Fig. 21). 
The  various  menus  only  offer  the  relevant...

17
ht3000e
To  access  these  submenus,  press  the  

18
ht3000e
NOiSE REDUCTiON 
This adjustment serves to select the noise reduction filter value. 
In this latter case, simply click on the slider and set the value 
with the ◀ and ▶ keys on the remote control. 
iMAgE
This  menu  features  adjustments  relating  to  picture  position, 
aspect ratio, magnification etc.
ASPECT
This  adjustment  allows  you  to  change  the  dimensions  and 
aspect  ratio  (relationship  between  width  and  height)  of  the 
displayed image. There are five preset aspects...

19
ht3000e
sising or attenuating the different grades of brightness (blacks, dark, medium, light grey, whites) in the projected image. The projector has a range of gamma functions which enable you to display any image to the best effect for the type of video source, the ambient lighting and your subjective preferences. There  are  4  sets  of  gamma  curves:  Standard  (ST),  Enhanced SIM2  (EN)  and  Graphics  (GR),  User.  The  Standard  curve  has been  defined  for  general  use,  and  is  set  for...

20
ht3000e
Enhanced set is suitable for watching movies. The Graphics set is suited to displaying synthetic graphics (PC, CAD, PC presenta-tions, etc.). User enables you to define your own curve. You can thus select the coefficient which determines the curve. Values from 1.5 to 2.2 allow you to emphasise the detail of dark images,  but  reduce  overall  contrast.  Values  higher  than  2.2 increase overall contrast, but reduce the detail of dark areas. 
For the most common video sources, the...