Sim2 Multimedia Ht300 E Projector User Manual

							
21

n the initial phase of installation the configurable keys (F1, F2) 
serve as optical zoom and optical focus (Fig.34).
POWER ON
If active (AUTO) allows to power up the system directly from the 
power feeder, once the initializing phase is completed.
If not active (STAND-BY) once the initializing phase is completed 
the system remains in a stand-by mode waiting to receive the 
power on command from the remote control or the key pad.
TEST PATTERNS
Displays a series of five test patterns, useful for the installation 
of the projector.
Press 
‚ and ·  keys to browse pattern.
FACTORY DEFAULTS
Reconfigures  the  projector  to  original  factory  settings  except 
Position, Orientation, Y/C Delay, Zoom and Focus.
NoConfirm?
Yes
MENU
LANGUAGELists  the  languages  available  for  the  On  Screen  Display  me-nus.
SOURCE LISTIn order for projector to be more flexible, the following described 
functions  allow  to  modify  the  input  selection  menu  making  it 
more user friendly.
The  main  window  shows  all  the  inputs  available  on  the  
projector.
If one or more inputs are not utilized, it is often helpful to blank 
them from the input list (accessed with the 0 key).
Once the input has been chosen, in the drop menu that appears 
by  pressing  the 
fl  key,  it  is  possible  to  activate  the  source  (Fig. 35).
The  exclusion  or  activation  of  the  source  will  automatically 
renumber the remaining active inputs.
2  S-VIDEO 
4  GRAPHICS RGB 
5  HDMI    HDMI    
1  VIDEO  123  COMP / RGB 345
S-VIDEO 3  
COMP RGB 5
HDMI 12 VIDEO 1  
S-VIDEO 4  
Source list/Edit source name
ACTIVE 
NAME
Yes
No
Fig.35
The inputs with an active video signal (visible in the input se
-
lection menu) are marked with a check symbol.
It can be also helpful to identify the input with a name chosen by 
the user (for example with the name of the connected source) 
rather than with the signal type.
Once  chosen  to  have  the  input  visible,  in  the  drop  menu,  by 
selecting the Name option it is possible to rename the source 
in  use.This  will  make  it  easier  to  remember  the  source  con
-
nected to a specific input. You can use up to 12 alphanumeric 
letters to name the source (for more details check the “Insert 
text” section)
INSERT TEXTYou will be able to insert text easily and rapidly by accessing 
the text insertion menu 
(Fig.36))
 
Fig.36
The text insertion mode remains the same if text is being inser
-
ted  for  the  first  time  or  if  a  previously  inserted  name  is  being 
edited. The letter insertion can be done in any available position 
(represented by horizontal lines).
Use the 
‡ and fl keys to move between letters either left or 
right respectively.
Press the numeric key matching the letter  (Fig. 36), the first click 
of the key selects the first letter, the second click the second 
letter and so on.
The available letters are shown in the text insertion menu. 
						

							
22

Once one letter has been inserted, to insert the following one it 
is necessary to move with the cursor in the next right position 
with the 
‡ key of the remote control, repeat this procedure to 
insert other letters. 
Use the 
· key to switch from small case to capital letters and viceversa.
Any mistake can be deleted with the ‚ key once it has been 
positioned on the wrong letter.
Once the text insertion process is finished, it can be confirmed 
and saved by clicking the MENU+ key.
If you want to delete the modifications use the 
MENU- key of the 
remote control.
F1/F2 KEYS
This  allows  to  assign  different  functions  to  the  remote  control 
keys, named F1 and F2.
The window is made of 6 options, once for each line and bytwo 
columns showing the F1-F2 keys. The choice between F1 and 
F2  is  made  by  the 
‡  and fl  keys  of  the  remote  control;  the 
function given to F1 and F2 is chosen with the 
· and ‚ keys.
The  function  delivered  by  the  key  is  memorized  by  the  inter
-
section on the line and column.
In the following window are described the 6 options.
Source list
F1/F2 keys
Source info
OSD Backgroung
OSD Position
OSD Timeout Language
Menu
English
Zoom
Focus
Magnification
Blank
Color temperature
Gamma correction
F1 F2
Fig.37
Zoom
Allows to access the optic zoom, where the fl and ‡  keys allow 
to increase or decrease the size of the projected image.
Focus
Once selected, the fl and ‡ keys allow to focus the image.
Magnification
Allows  you  to  select  the  area  to  be  viewed  and  then  magnify 
the projected image. The degree of enlargement is selected in 
Zoom mode (identified by a magnifying glass in the centre of the 
image) using the 
fl and ‡  keys. The area of the picture to be  enlarged is selected  in Pan mode (symbol in the centr
e of the 
picture) using the  
· and fl, ‡   arrow keys. You can toggle 
between Zoom and Pan mode by pressing the  F1/F2
key on the remote control.
BlankBlanks  the  active  video  signal  producing  a  completely  black 
screen. Once pressed the key an indication of a few seconds 
on the OSD will confirm its activation. A click of any other key 
of the remote control allows to restore the previous settings.
Color temperatureThe following click of the key (F1 or F2) allows to choose between 
the different values of the grid (fig. 30). The | and | key allow to 
move  along  vertical  lines,  keeping  the  same  color  temperature 
but choosing different values from the black body curve. Using 
the  keys, you can choose different color temperature 
values.
Gamma correctionThe  following  click  of  the  key  (F1  or  F2)  allows  to  choose 
between  the  different  gamma  values  available.  You  can  also 
use the  keys to select the most appropriate curve.
SOURCE INFORMATIONWhen active (YES) each source change will show the information 
related to the signal. If not active (NO) there will be no information 
on the selected source.
OSD BACKGROUND
Determines  the  type  of  background  for  the  On  Screen  Di-
splay.
OSD TIMEOUTUse this adjustment to set the display time after which the On 
Screen Display will disappear.
OSD POSITIONAllows the On Screen Display to be positioned in a particular 
area of the projected image. The OSD can be positioned using 
the arrow keys for fine adjustments or keys 1...9 on the remote 
control to select one of 9 preset positions. 
						

							
23

MEMORIES
The  main  parameters  of  the  image  may  be  saved  in  distinct 
groups  of  values  (known  as  ‘Memories’);  these  parameters 
can  subsequently  be  applied  all  together  by  way  of  a  single 
command.
There are 3 distinct Memories (Memory 1, Memory 2, Memory 
3)  for each of the 8 signal types managed:
3  COMP/RGB(YCrCb 15KHz) 3  COMP/RGB(RGB 15KHz) 
3  COMP/RGB(YCrCb)  3  COMP/RGB(RGB) 
4  GRAPHICS RGB 
5  HDMI 1  VIDEO  
2  S-VIDEO  
making a total of 24 different available Memories.
The  image  parameters  that  can  be  saved/recalled  by  the 
Memories management system are the following:
Image 
Picture
BRIGHTNESS  ASPECT
CONTRAST  COLOR TEMP.
COLOR  OVERSCAN
TINT  GAMMA 
SHARPNESS 
FILTER 
SHARPNESS MODE
VIDEO TYPE
NOISE REDUCTION
Some  of  these  parameters  may  not  be  available  for  certain 
inputs or certain input signals, as indicated in Tables 1 and 2.
The  menu  page  for  the  Memories  management  functions  is 
activated by pressing the
   key on the remote control or the  
fl key on the keypad (Fig.38).
ZOOM
CONTROL (RS 232) GRAPHICS RGB12
4
���
� � � �
Fig.38
The  operations  that  can  be  performed  on  each  memory  se
-
lected are described here below. SAVE A MEMORY
To save the current values of the image parameters in Memory 
1, use the 
· and ‚ keys to move to line ‘1’ and then open the 
pull-down menu by pressing the  
fl  key  (Fig.39) . Then select the 
option ‘Save current settings’. To confirm that the operation has 
been  completed  successfully,  the  message  ‘Current  setti
ngs 
saved in Memory 1’ is displayed at the bottom of the screen and 
the letter ‘S’ appears to the left of the memory name. The same 
procedure is used to save parameters in Memories 2 and 3.
0  Auto
3        S   MEMORIA 1
Memories
Save current settings
Save initial settings
Rename
2   
     I   1       S   
Fig.39
RECALL A MEMORY
To recall a Memory, select the desired line and press 
‡. The 
parameters  saved  in  the  selected  Memory  will  be  applied  to 
the  image  displayed  and  a  message  will  appear  to  confirm 
the  operation  ‘Memory  1  recalled’.  The  Memory  recalled  will 
be  associated  with  the  source  and  signal  type,  and  will  be 
automatically  recalled  every  time  that  particular  source  and 
signal type combination is selected.
SAVE DEFAULT SETTINGS
To restore the original values to a previously modified Memory, 
select  the  line  corresponding  to  the  Memory  in  question  and 
open the pull-down menu ( 
fl key). Then select the line   “Save 
default  settings”.    To  confirm  that  the  operation  has  been 
completed  successfully,  the  message    ‘Initial  settings  saved 
in Memory 1’ is displayed at the bottom of the screen and the 
letter ‘I’ appears to the left of the name of the memory.
RENAME A MEMORY
It  is  possible  to  assign  a  name  to  each  Memory.  To  assign  a 
name (with a maximum length of 12 alphanumeric characters) 
to a Memory, select the option ‘Rename’ from the correspond
-
ing  pull-down  menu.  Enter  the  text  following  the  procedure 
indicated  in  paragraph 
“ SOURCE  LIST”.  informazioni,  che 
tengono  conto  delle  Memorie  eventualmente  selezionate  nel 
penultimo accesso alla pagina ‘Memorie’.
RESTORE CURRENT SETTINGS
On entering the ‘Memories’ menu, a copy of the current settings  
						

							
24

is  saved  in  a  temporary  menu  (labelled  with 0  -  AUTO).  Once 
one or more memories have been recalled, you can restore the 
settings that were effective at the moment the Memories menu 
was  accessed  by  selecting 
0  -  AUTO.  However,  this  operation 
must be completed before the  ‘Memories’ menu page disap
-
pears  (30  seconds  after  the  last  operation  commanded  from 
the  remote  control  or  the  keypad).  The  next  time  it  appears, 
the temporary memory will contain new information that takes 
into account any Memories selected the penultimate time the 
‘Memories’ page was accessed.
Memory  0  (
-  AUTO)   can  be  used  even  when  you  do  not  wish 
to  enable  the  Memories  management  function  for  the  signal 
currently in use. Once Memory 0 has been selected, when a 
source  is  chosen,  the  settings  that  were  effective  at  the  time 
the    Memory  was  previously  recalled  will  be  automatically 
applied.  
INFO
Displays  the  current  status  of  the  projector  and  information 
concerning the projected video/graphic signal.
This function is displayed on pressing 
   on the remote control 
(or, in the absence of the On Screen Display, the 
‡ key on the 
remote control).
QUICK MENUS
The Quick menus allows the adjustment of most of the picture 
quality controls without recalling the main On Screen menus.
Brightness, Contrast, Color, Tint, Sharpness and Filter adjust
-
ments  appear  at  the  bottom  of  the  screen,  one  after  another, 
when Up and Down Arrow keys are pressed.
MESSAGES
The following messages could appear on your screen:
No Signal
The projector does not recognise any signal sent through the 
selected input.- Check that the selected input is actually connected to
  a video or graphic signal.
-  Verify  compatibility  of  video/graphic  signals  with  technical  specifications of your projector.
-  Check the integrity of cables used to connect various   sources.
Out of range
Either the resolution or the horizontal/vertical frequency of the 
input signal is too high.
- Input a signal that is within specifications.
10   CLEANING AND MAINTENANCE
The projector does not require internal cleaning. There are no 
user  serviceable  parts  inside  the  projector.    Please  refer  all 
service requirements to qualified personnel.
Cleaning the projector’s cover:
 
Use a soft slightly damp cloth. Do not use abrasive cleaners, 
solvents  or  other  harsh  chemicals,  as  this  will  damage  the 
finish  of  the  cover.  Avoid  direct  cleaning  of  the  rear  panel’s 
screen-printing.
Cleaning the lens:
The lens may be cleaned with a very soft, non-abrasive small 
brush, in order to remove dust particles.  Alternatively, use a soft 
dry cleaning cloth (of the type used for camera lens cleaning) 
to remove fingerprints and grease marks. 
						

							
25

11   TROUBLESHOOTING GUIDE
No power  (Green and red LED are OFF) 
-  Check the power switch at the rear: it must be in position 
I.
-  Check if the power cable has been connected correctly to a 
working socket.
-  Check the power socket fuse, at the rear of the projector.
-  Replace the fuse on the mains socket with an identical type  
(T 3.15A H) (Fig. 2). 
-  Should the problem persist, seek authorised technical assi
-
stance.
The lamp is not coming on
-  Allow a few minutes pause between switching off and turning  on again (from stand-by). This will allow the lamp to cool down 
sufficiently.
-  If the lamp doesn’t come on – even though the projector has  had sufficient time to cool down – seek technical assistance 
from your nearest Dealer.
No image
-  Check that the selected input is actually connected to a active 
video or graphic signal.
-  Check that the above source actually works. 
-  Verify compatibility of video/graphic signals with the   technical  specifications of the projector.
-  Check the integrity of cables used to connect various sour
-
ces.
- Check temperature of the room: it must be below 35°C  
(95°F) 
- Check projector air vents on top and underneath the projector:  they must be free of obstruction.
- If the problem persists, consult your Dealer.
Image is disturbed, unstable or noisy
-  Verify compatibility of video/graphic signals with the technical  specifications of the  projector.   
-  Check the integrity of cables connecting projector to various  sources.
-  If the signal source is a terrestrial broadcast (via a VCR) check  that  the  receiving  channel  has  been  correctly  tuned  in  and 
that the aerial system is in good working order. 
- Should the problem be present with a signal coming from a 
video-recorder, ensure that the videotape is an Original “first 
generation” copy and in good condition. 
- Adjust  the  VCR’s  tracking  control  for  optimum  picture  per-
formance.  Ensure  the  VCR  mode  is  active  in  the  Picture  
menu.
Incomplete image along borders (vertical and horizontal) 
-  Compare compatibility of video/graphic signals and technical 
specifications of your projector.   
- Press  Auto (on your remote or keypad) to execute automatic 
adjustments.       
- Adjust the horizontal and vertical position of projected ima-
ge  by  selecting   
Position  on  the  Image  Adjustments 
menu.
- Adjust the width and height of image, selecting Aspect in 
the Image Adjustments menu.
Image too dark, too pale or unnaturally coloured
- Verify  compatibility  of  video/graphic  signals  with  technical 
specifications of your projector.   
- Go to  Picture  menu, select and regulate any of the following, 
accordingly: 
Contrast, Brightness, Color, and Tint.
-  If necessary, reset the  Color Temperature and 
Gamma 
Correction  (found on the  Image Adjustments  / Advan
-
ced Settings menu).
 Graphic image with poor quality vertical detail
 
-  Verify compatibility of video/graphic signals with technical 
specifications of your projector.
-  Press 
Auto (on your remote or keypad) to execute auto-
matic adjustments.
-  Adjust Frequency
 and Phase  parameters, found in the 
Image Adjustments menu, to optimise vertical detail of 
the projected image. 
						

							
26

You  can  purchase  the  following  optional  accessories  at  your 
Dealer:
  - Wall/Ceiling Bracket Kit.
12   OPTIONAL ACCESSORIES
Use  only  original,  or SIM2  Multimedia  approved,  acces-
sories.
CAUTION: for ceiling/wall installation, by means of 
suspension  bracket,  carefully  follow  the  instruc
-
tions and safety instructions recommended by the 
Manufacturer in the bracket’s literature.
Video  Image  showing  colour  misalignment  on  vertical 
details
-  Verify  compatibility  of  video/graphic  signals  with  technical  specifications of your projector.
-  Adjust  Y/C  Delay  settings  in  the  Image  Adjustments  /  Advanced Settings to reduce colour misalignment. For best 
results use an external colour bar test pattern source. 
           
Remote control does not work 
-  Check the batteries and for correct polarity.
-  Ensure  that  the  area  between  the  infrared  sensor  (front  of projector) and the remote control is free of obstruction.
-  Ensure that infrared sensors (front and rear of projector) are 
not exposed to intense light levels. 
						

							
27

A   TECHNICAL SPECIFICATIONS
OPTICAL HT280E 
Projection system:   optical  engine  based  on  1  DMD™ sealed housing, dusty proof
DMD™ panel:   resolution 1024x576 pixel
Brightness uniformity:   10% above or below the average  
Contrast ratio:   > 3000:1 (full On / full Off)
Projection lens:   zoom,  12  elements  AR  multilayer  coating, motorized focus and zoom, 
manual elevation
Aperture f#:   2.7 (zoom max) - 3.3 (zoom min)
Picture size:  50-250 inches (diagonal measure)
Aspect ratio:  4/3 and 16/9
Throw ratio:  2.1:1 - 3:1:1
(throw distance: picture width) 
Focus range: 2.2 - 13.0 m (7’ 3” - 42’ 8”) 
Throw Distance:  60”: 3m - 4.1m 
  80”: 4m - 5.5m 
  100”: 5m - 6.8m 
Keystone adjustement: up to 28° (optical: ± 10° digital: ±18°) Not available with 1080i input signal
Lamp:  120 W
Lamp life time:  8000 hours (average value measured  in the laboratory under optimal condi
-
tions; it can be sensibly reduced by 
the unit misusing)
OPTICAL HT300E 
Projection system:   optical  engine  based  on  1  DMD™  DarkChip3
TM chip,sealed  housing, 
dusty proof
DMD™ panel:   resolution 1280x720 pixel
Brightness uniformity:   10% above or below the average  
Contrast ratio:   > 3500:1 (full On / full Off)
Projection lens:   zoom,  12  elements  AR  multilayer  coating, motorized focus and zoom, 
manual elevation
Aperture f#:   2.7 (zoom max) - 3.3 (zoom min)
Picture size:  50-250 inches (diagonal measure)
Aspect ratio:  4/3 and 16/9
Throw ratio:  1.8:1 - 2.5:1
(throw distance: picture width) 
Focus range: 2.2 - 13.0 m (7’ 3” - 42’ 8”) 
Throw Distance:  60”: 2.4m - 3.3m 
  80”: 3.2m - 4.4m 
  100”: 4.0m - 5.5m 
Keystone adjustement: up to 26° (optical: ± 8° digital: ±18°)
Lamp: 120 W
Lamp life time:  8000 hours (average value measured  in the laboratory under optimal condi
-
tions; it can be sensibly reduced by 
the unit misusing) 
						

							
28

ELECTRICAL
Input Signals:  C V B S   o n   R C A / P h o n o   t y p e   c o n-
nector
  S-VHS on Mini-DIN connector
  RGBHV on DB15HD connector
  RGBS  /  YCrCb  on  RCA/Phono  type 
connector
  HDMI™
Horizontal frequency:  from  15  to  80  kHz  (up  to  to  UXGA  format @ 60 Hz)
Vertical frequency:  48-100 Hz
Video standards :  automatically selected (PAL B,G,H, I, 
M,N,60, SECAM, NTSC 3.58, 4.43)
High definition video:  ATSC HDTV (480p, 720p, 1080i)
Graphic standards :  VGA, SVGA, XGA, SXGA, UXGA
Deinterlacer:  Faroudja  chip  set,  DCDi
™,  3:2  pull 
down sequence convertion
Video processor:  DTI,  CTI,  comb  filter,  noise  reduc
-tion.
  Sharpness, Y/C delay and NTSC tint 
adjustments
Remote control:  via  infrared  remote  control  and  via  computer through RS232 serial inter
-face
Low Volt. Power Output:  two  12  Vdc  output,  100  mA  max  on 
jack connectors
Output :  Optical  Digital  Audio  on  TOSLINK 
connector
GENERAL
Supply:  from  100  to  240  Vac,  -10%  +6% tolerance
Frequency:  from 48 to 62 Hz
Consumption:  180 W max
Fuse:  T 3.15A H, 5 x 20 mm
Dimensions of projector:  3 5 2   m m   x   1 7 4   m m   x   3 1 8   m m 
(LxHxD)
  13”-7/8 x 6”-7/8 x 12”-1/2 (LxHxD)
Weight of projector:  5.0 kg (11 lbs)
Packaging and   4 0 0 m m   x   2 7 5   m m   x   4 0 5   m m 
(LxHxD)
gross weight:  1’ 4” x 11” x 1’ 4” (LxHxD) 
  double reinforced carton; expan
-dable anti-shock packaging;
  gross  weight,  including  accesso-ries: 
  8  kg  (17.7  lbs);  recyclable  packa-ging material 
ENVIROMENTAL
Operation temperature:  0 to 35°C (32° to 95°F)
Transportation temp.:  -10 to 55°C (14° to 131°F)
Storage temperature:  -10 to 55°C (14° to 131°F)
Humidity: 10% to 90% relative humidity non-
condensing
Safety:  EN 60950, UL 60950
Transportability:  desktop equipment
Electromagnetic   EN 55022 Class B
compatibility:  EN 55024
  EN 61000-3-2
  EN 61000-3-3
Transportation:  IEC 68-2-31, IEC 68-2-32 
						

							
29

B   DIMENSIONS
74 352 
174 
102 
318
(Fig.40b)(Fig.40a)
unit: mm (inches)
C   PROJECTION DISTANCES
Follow the table below to determine the optimal projection distance “L” between the screen (Fig.40a) and the center of the lens. 
This will help you to obtain the desired screen size.The manual lens shift adjustments allows the projected image to be moved 
vertically, up or down, in relation to the centre of the screen 
(Fig.40b). If the distance “H” between the centre of the screen and the 
centre of the lens exceed Hmax, it is necessary to tilt the projector and use the digital keystone to correct the image projected. 
H
H
LL  
						

							
30

Projection distance table HT280E
Projection distance table HT280E   Screen   Screen                             
  size    width                                 
  
(diagonal)              min L                Hmax                   max L                     Hmax      
Min projection distance
16/9
  3,4  11’  2” 
  4,1  13’  5” 
  4,8  15’  7” 
  5,5  17’  9” 
  6,2  20’  2” 
  6,8  22’  4” 
  7,5  24’  7” 
  8,2  26’  9” 
  10,3  33’  6” 
  12,3  40’  4” 
  13,7  44’  9”
Max projection distance
  1,1  43” 
  1,3  51” 
  1,6  63” 
  1,8  71” 
  2  79” 
  2,2  87” 
  2,4  94” 
  2,6  102” 
  3,3  130” 
  4  157” 
  4,4  173”    m   in.   m       ft. in.   m       ft. in.
  0,4 
1’ 5”   
  0,5   
1’ 9”  
  0,6 
2’ 0”   
  0,7 
2’ 4”   
  0,8  
2’ 7”   
  0,9 
2’ 10”  
  1,0  
3’ 1”   
  1,0  
3’ 5”   
  1,3  
4’ 3”   
  1,6 
5’ 2”   
  1,7  
5’ 9”   m       ft. in.
  m       ft. in.
  0,6 
2’ 0”   
  0,7   
2’ 4”  
  0,8 
2’ 9”   
  1,0 
3’ 2”   
  1,1  
3’ 7”   
  1,2  
3’ 11”  
  1,3  
4’ 4”   
  1,4  
4’ 9”   
  1,8  
6’ 0”   
  2,2 
7’ 1”
  2,4 
7’ 11”
  2,5  8’  1” 
  3,0  9’  7” 
  3,5  11’  3” 
  4,0  13’  0” 
  4,4  14’  6” 
  4,9  16’  2” 
  5,4  17’  8” 
  5,9  19’  4” 
  7,4  24’  3” 
  8,9  29’  2” 
  9,9  32’  4”
50”
60”
70”
80”
90”
100”
110’
120”
150”
180”
200”
in.
  Screen   Screen                             
  size    width                                
  
(diagonal)                min L         Hmax                  max L                     Hmax      
Min projection distance
4/3
  4,2  13’  8” 
  5,1  16’  6” 
  5,9  19’  3” 
  6,7  22’  1” 
  7,6  24’  9” 
  8,4  27’  6” 
  9,3  30’  4” 
  10,1  33’  1” 
  12,6  41’  4” 
  -  -
  -  -
Max projection distance
  1  39” 
  1,2  47” 
  1,4  55” 
  1,6  63” 
  1,8  71” 
  2  79” 
  2,2  87” 
  2,4  94” 
  3  118” 
  3,6  142” 
  4  157”    m   in.   m       ft. in.   m       ft. in.
  0,5 
1’ 9”   
  0,7   
2’ 2”  
  0,8 
2’ 6”   
  0,9 
2’ 10”  
  1,0  
3’ 2”   
  1,1  
3’ 6”   
  1,2  
3’ 11”  
  1,3  
4’ 3”   
  1,6  
5’ 3”   
  1,9 
6’ 4”   
  2,2  
7’ 3”   m       ft. in.
  m       ft. in.
  0,7 
2’ 5”   
  0,9   
2’ 11”
  1,0 
3’ 5”   
  1,2 
3’ 11”  
  1,3  
4’ 5”   
  1,5  
4’ 10”  
  1,6  
5’ 5”   
  1,8  
5’ 10”  
  2,2  
7’ 3”   
  -  -
  -  -
  3,0  9’   7” 
  3,7  12’  1” 
  4,3  14’  1” 
  4,9  16’  0” 
  5,5  18’  0” 
  6,1  20’  0” 
  6,7  22’  0” 
  7,3  24’  0” 
  9,1  30’  0” 
  11,0  36’  0” 
  12,2  40’  0”
50”
60”
70”
80”
90”
100”
110’
120”
150”
180”
200”
in.