Sim2 Multimedia Grand Cinema C3x Projector User Manual

							
cod. 46.0533.000
User and Installation Manual
c3X - c3X LITE  
						

							


MENUSOURCEESC

Switches off to stand-by
Activates the On Screen  Display MenuNavigates menu pages
▲,▼,◀,▶
Navigate through andmake adjustement to the On Screen Menu
Display the sourceSelection Menu
Deactivates the On Screen Menu
1  TELECOMANDO E TASTIERA DI CONTROLLO
LIGHT
F1ZOOM
FOCUSF2
0-9 KEYSSwitch  on  from  stand-by  mode  and  allow  direct source selection
STAND-BYSwitches off to stand-by
ESCAPEDeactivates the On Screen Menu
UP/DOWN/LEFT/RIGHT ARROW KEYSNavigate  through  andmake  adjustement  to  the  On Screen Menu
MENU +Activates the On Screen Display menusNavigate menu pages
MEMORIESActivates memories menu
INFODisplays the selected source informationand the projectors status
ASPECTSelects image Aspect ratio
VCRImproves the video recorder signals quality
SOURCE Display the source Selection Menu
BLANK SCREEN
MENU Activates the On Screen  Display MenuNavigates menu pages
FREEZEFreezes a moving picture
ZOOMActive le réglage du zoom de l’objectif.
FOCUSSelects focus lens adjustement
BACK LIGHT Turn on the back light
AUTOSelect Auto Adjust (automatic optimisation of the displayed image) 
						

							
3

Adaptation of the input signal resolution to the Projector resolution oc-curs without alterations of image quality, in accordance with an ample choice of aspect ratios, including several definable by the user.
All image adjustments can be performed with the remote control with the aid of the On Screen Display; alternatively, the unit can be controlled by from a home automation system through the serial port.
SIM2 carries out comprehensive functional testing in order to gua-
rantee the maximum product quality.
For  this  reason,  when  you  start  using  the  product  lamp  operating 
hours may already be at between 30 and 60. 
In  addition  to  the  regular  tests,  the  Quality  Control  department 
performs additional statistical tests at the time of shipment. 
In this case the packing may show signs of having been opened, 
and the accumulated lamp operating hours may be slightly higher 
than the hours associated with the standard tests.
Thanks  to  the  new  optical  system  based  on  three  chip  DMD™,  the c3X  allows  to  take  advantage  from  DLP™  technology,  the  Texas Instruments technology.
Each of the three DMD™ chip is dedicated to the modulation of one of  the  primar y  colors  coming  from  the  optical  prism,  the  refl  ected light, after combination by a second prism, is projected outside using an appropriate lens system.The technology of the  c3X allows to obtain images without rainbow effect or any other type of artefact, in order to enjoy an even more realistic images.
The large number of inputs available (1  composite Video inputs, 1 S-Video inputs,  c omponent or RGB inputs, 1 graphic RGB inputs, 1 DVI-D input,  1  HDMI™  Input)  ensures  the  system  supports  a  wide  variety  of analogue and digital sources: DVD players, V cRs, satellite and terrestrial receivers, computers, game consoles, video cameras, etc.
c onversion of interlaced video signals to progressive signals by means of prestigious DcDi™ technology produces fluid, natural, images free of flicker and stairstepping artefacts.Faithful  reproduction  of  signals  at  higher  resolutions  (such  as  high definition  video  and  graphics)  occurs  without  loss  of  information  or reduction of image sharpness thanks to the processor ’s high pixel rate signal acquisition capabilities.
DLP and DMD are registered trademarks of Texas Instruments.HDMI,  the  HDMI  logo  and  High-Definition  Multimedia  Interface  are  trademarks  or registered trademarks of HDMI Licensing LL c
1  INTRODUCTION
10   cLEANING AND MAINTENANcE  6
11   TROUBLESHOOTING GUIDE  6
1    OPTIONAL AccESSORIES  7
     A - Technical specifications  8
     B - On Screem Menu  9
     B - Dimensions  30
TABLE OF CONTENTS
1 PRESENTATION  3
 IMPORTANT SAFETY INSTRUcTION  4
3 DISIMBALLO  7
4 UNPAcKING  8
5 SWITcHING ON AND OFF THE PROJEcTOR  10
6  cONNEcTION  10
7  cONNEcTION PANEL 1
8 REMOTE cONTROL  14
9 ON ScREEN MENU  15 
						

							
4

ATTENTION:
To reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing the top cover of 
the projector. Refer to trained, authorised personnel for technical assistance.
Prior to switching on the projector please read each chapter of this manu\
al carefully as this manual provides basic instructions for using the projector.The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal of the top cover, must be carried out by authorised, trained technicians. There are no user serviceable parts inside. To ensure safe and long term reliability please use power cables supplied with the projector. Observe all warnings and cautions.
This symbol indicates the presence of impor-
tant  instructions  regarding  use  and  mainte-
nance of the product.
2 IMPORTANT SAFETY INSTRUCTIONS
This symbol indicates the possible electric 
shock  hazard  associated  with  uninsu-
lated  live  components  in  the  interior  of 
the unit.
LAMP WARNING:If the lamp should suddenly break with a loud bang, air the room thoroughly before using it. Do not replace the lamp: seek qualified technical 
assistance from your nearest Dealer.
ENVIRONMENTAL INFORMATION:
The product you have purchased contains extracted natural resources that have been used in the manufacturing process. This product 
may  contain  substances  known  to  be  hazardous  to  the  environment  or  to  human  health.  To  prevent  releases  of  harmful  substances 
into the environment and to maximize the use of natural resources, SIM Multimedia provides the following information on how you can 
responsibly  recycle  or  reuse  most  of  the  materials  in  your  ”end  of  life”  product.  Waste  Electrical  and  Electronic  Equipment  (commonly 
know as WEE) should never be disposed of in the municipal waste stream (residential garbage collection). The “crossed-Out-Waste Bin” 
label  affixed  to  this  product  is  in  your  reminder  to  dispose  of  your  “End  of  Life”  product  properly.  Substances  such  as  glass,  plastic,  and 
certain chemical compounds are highly recoverable, recyclable, and reusable. You can do your part for the environment by following 
these simple steps:
1. When your electrical or electronic equipment is no longer useful to you, “take it back” to your local or regional waste collection 
administration for recycling.
2. In some cases, your “end of life” product may be “traded in” for credit towards the purchase of new SIM2 Multimedia equipment. 
Call SIM2 Multimedia to se if this program is available in your area.
3. If you need further assistance in recycling. Reusing, or trading in your “end of life” product, you may contact us at the Customer 
Care number listed in your products user guide and we will be glad to he\
lp you withy our effort.
Finally, we suggest that your practice other environmentally friendly actions by understanding and using the energy-saving features of this 
products (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and 
by disposing of a or recycling used properly. 
With your help, we can reduce the amount of natural resources needed to procedure electrical and electronic equipment, minimize the 
use  of  landfills  for  the  disposal  of  “end  of  life”  products,  and  generally  improve  our  quality  of  life  by  ensuring  that  potentially  hazardous 
substances are not released into the environment and are disposed of pro\
perly. 
						

							


•   Read this manual carefully and keep it in a safe place for future 
consultation.
	 This 	 manual 	 contains 	 important 	 information 	 on 	 how 	 to 	 install 	 and 	
use 	 this 	 equipment 	 correctly. 	 Before 	 using 	 the 	 equipment, 	 read 	
the 	 safety 	 prescriptions 	 and 	 instructions 	 carefully. 	 Keep 	 the 	 manual 	
for 	 future 	 consultation.
• 
  Do not touch internal parts of the unit.
	 The
	 unit 	 contain 	 electrical 	 parts 	 carr ying 	 high 	 voltages 	 and 	 opera
-
ting
	
at
	
high
	
temperatures.
	
Do
	
not
	
remove
	
the
	
cover
	
from
	
the
	
unit, 	
refer
	
to
	
qualified
	
service
	
personnel
	
for
	
all
	
repair
	
and
	
maintenance 	
requirements.
	
The
	
warranty
	
will
	
be
	
automatically
	
invalidated
	
if
	
the 	
cover
	
is
	
removed
	
from
	
the
	
unit.
	
• 
 
Power supply disconnect device.
	 The
	
device
	
for
	
disconnecting
	
the
	
units
	
from
	
the
	
mains
	
power 	
supply
	
is
	
constituted
	
by
	
the
	
power
	
cable
	
plug.
	
Ensure
	
that
	
the 	
power
	
cable
	
plugs
	
and
	
the
	
electrical
	
mains
	
socket
	
outlets
	
are 	
easily
	
accessible
	
during
	
installation
	
operations.
	
To
	
disconnect
	
the 	
unit
	
from
	
the
	
electric
	
power
	
supply,
	
pull
	
the
	
plug
	
to
	
remove
	
it
	
from 	
the
	
socket
	
outlet.
	
Do
	
not
	
pull
	
the
	
power
	
cable.
1	 Projection 	 lens.
2	 Aesthetic 	 embrasures
3	 Remote
	 control 	 front 	 / 	 IR 	 sensor
4	 Cooling
	 air 	 inlet 	 vents

	 Adjustable 	 levelling 	 feet
6	 Adjustable
	 carr y-handle
7	 Lamp
	 Box
8
	 	 Fused 	 power 	 socket 	
9	 Main
	 power 	 switch
10	 Main
	 function 	 keys11	Composite 	 video 	 input
12 	 	S-Video
	 input
13
	 	RGB
	 / 	 YPrPb 	 input
14
	 	HDMI™
	 input
1
	 	Audio
	 Output
16
	 	Remote
	 Control 	 connector
17
	 	VGA
	 input
18
	 	Serial
	 interfaces 	 RS232
19
	 	
	Interfaces 	 USB 	 1.1
20	12Vdc 	 screen 	 output
PROjectOR
•  Use only the specified type of mains power supply.
	 Connect 	 the 	 units 	 to 	 a 	 mains 	 electrical 	 supply 	 with 	 rated 	 voltage 	 of 	
between 	 100-240 	 VAC, 	 0/60 	 Hz 	 and 	 equipped 	 with 	 a 	 protective 	
earth 	 connection. 	 If 	 you 	 are 	 unsure 	 of 	 the 	 type 	 of 	 mains 	 power 	
supply 	 in 	 your 	 home, 	 consult 	 a 	 qualified 	 electrician. 	 Ensure 	 that 	
the 	 power 	 draw 	 of 	 the 	 units 	 is 	 commensurate 	 with 	 the 	 rating 	 of 	
the 	 electrical 	 socket 	 outlets 	 and 	 any 	 extension 	 cables 	 that 	 are 	
used.
• 
 
c onnect the unit to a mains electrical supply
  Make 	 the 	 connection 	 as 	 shown 	 in 	 Fig.2
																																																																								\
											 Fig.2
100-240 Vac 50/60 Hz 
HDMI 1ESCSOURCE5
0I
1423+12V
USB 1.1R/Pr              RS232
GRAPHICS RGB
C/YB/PbHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
3
2VIDEO
MENU
ESCSOURCE
1
5
4
0I
8910
171615141819
131211
1
5
67
REMOTE
20 
						

							
6

 Replace the safety fuse
 Before  making  the  replacement  disconnect  the  appli-
ance from the mains power supply.
 The  fuse  compartment  is  close  to  the  mains  power  con-
nector (Fig. 3). Use a slotted screwdriver to remove the fuse 
carrier () and replace the fuse (3). Insert a new spare fuse 
(4). Use only T 5A H fuses.
Fig.3
•  Beware of power supply cables. Position the power supply cables so that they do not consti-tute an obstruction. Position the power supply cables where they  cannot  be  reached  by  children.    Install  the  units  as close as possible to the wall electrical socket outlet. Do  not  tread  on  the  power  cables,  make  sure  that  they are not tangled or pulled; do not expose the power cables to heat sources; make sure that the power cables do not become knotted or kinked. If the power cables become damaged, stop using the system and request the assistan-ce of an authorised technician.
•  Disconnect the apparatus from the mains power supply in the event of electrical storms and when not in use. To avoid damage that could be caused by lightning striking in the vicinity of your home, disconnect the unit in the event of electrical storms or when the system will remain unused for prolonged periods. 
•  Avoid contact with liquids and exposure to humidity.  Do  not  use  the  unit  near  water  (sinks,  tanks,  etc.);  do  not place objects containing liquids on top of or near the unit and do not expose them to rain, humidity, dripping water or spray; do not use water or liquid detergents to clean the unit.
•  Prevent the unit from overheating. In order to allow the Projector cooling, keep at least 40 cm ( 16”) of space between the rear of the projector and the nearest wall or obstruction. Do not place the devices near heat  sources  such  as  heaters,  radiators  or  other  devices that generate heat (including amplifiers).  Do not obstruct ventilation openings. Do not place the unit in confined, poorly ventilated positions (bookcases, shelves, etc.). 
•  Do not expose the eyes to the intense light emitted by the lamp. Never  look  directly  at  the  lamp  through  the  ventilation opening when the unit is switched on. Risk  of  eyesight  impairment.  Ensure  also  that  children  do not look directly at the lamp. •  Beware of the lens movements Avoid positioning objects close the lens. The movements ( horizontal and vetical) could be  obstructed by objects, or damage may arise from the fall of the objects. 
•  Position the unit on a stable surface. To avoid serious injur y to persons and damage to property, make sure the units are placed on a level, flat and stable surface from which they cannot fall, tip over or slide. Pay special attention if the units are placed on a trolley so that they can be moved around. Ensure that the units are not subjected to impact. 
•  Do not insert objects through the unit openings. Make sure that no objects are inserted inside the units. If this should occur, disconnect the unit from the power supply 
immediately and call an authorised technician.
•  Energy Saving
   When  the  system  is  left  idle  for  a  long  period  disconnect 
the Projector from the main power supply.
 This precaution allows to save energy and to prevent wear 
and tear of the electronics devices.
ESCSOURCE
5
0I250 V T 3.15A H 
3
4
21 
						

							
7

1
2
3
4

3  UNPACKING
To  unpack  the  projector  safely  and  easily  please 
follow steps 1 to 5, as per drawing (Fig. 4).
It is recommended that the carton and packaging is 
retained for future use and in the unlikely event that 
your projector needs to be returned for repair.
Fig.4
PACKAGE CONTENTS
Fig.5
The carton should contain the following:
-  the projector  
- the remote control
- four 1.5V AAA batteries (for remote control)
- three  power  cables  for  the  projector  (EU,  UK, 
USA)
- the user and installation manual.
If any accessories are missing, contact your Dealer 
as soon as possible (Fig. 5).
Projector
User andinstallation manual.
Remote control
1.5V AAAbatteriesPower cablesEU, UK, US  
						

							
8

CAUTION:  In  the  case  of  ceiling  or  wall  mounting  using  a 
suspension  bracket,  follow  the  instructions  carefully  and 
comply  with  the  safety  standards  you  will  find  in  the  box 
together with the bracket. If you use a bracket different to 
the one supplied by SIM2 Multimedia, you must make sure 
that  the  projector  is  at  least  65  mm  (2-9/16  inch)  from  the 
ceiling and that the bracket is not obstructing the air vents 
on the lid and on the bottom of the projector.
Adjust the feet underneath to obtain a level position, lining up 
the base of the projected image to the base of the projection 
screen (Fig. 6).
+12VUSB 1.1R/CrCONTROL (RS232)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0I
Fig. 6
Position the projector the desired distance from the screen: the 
size of the projected image is determined by the distance from 
the lens of the projector to the screen and the zoom setting. See 
“Appendix c ”: Projection distances” for more information. 
Use the motorised lens zoom to adjust the image size and the 
motorised lens focus to achieve maximum clarity.
With  optimum  focus  you  should  be  able  to  clearly  see  each 
single  pixel  when  within  close  proximity  to  the  screen  (Fig.  7). 
7).+12VUSB 1.1R/CrCONTROL (R S232)GRAPHICS RGBC/YB/C bHVS-VIDEOAUDIO  OUTHDMI 1REMOTE32S-VI DEOME NUESCINPUT154
0I
ZOOM
ZOOM
ZOOM
ZOOM
F1
FOCUSAUTO ASPECTVCR
HELP ZOOM
F2
ZOOM
FUOCO
FUOCO
FUOCO
FUOCO
Fig. 7
L’immagine  può  essere  centrata  utilizzando  le  regolazioni  di 
spostamento motorizzato dell’obiettivo. Le traslazioni possono 
essere sia verticali che orrizontali (Fig. 8).
+12VUSB 1.1R/CrCONTROL (RS232)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0I
+12VUSB 1.1R/CrCONTROL (RS232)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0I
  Fig. 8Fig. 8
In  the  event  you  are  unable  to  centre  the  image  within  the 
screen  area,  tilt  the  projector  until  the  image  is  correctly  po-
sitioned.Any keystone error can be removed by the Keystone 
adjustment in the Set up menu (Fig.8-8a). 
4   INSTALLATION 
						

							
9

+12VUSB 1. 1R/CrCON TROL (R S232)GRAPHIC S RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMO TE32S-VIDEOMENUESCINPUT154
0I
TRAPEZIO 
20%

  
Fig. 8a
The  Orientation  adjustment  in  the  Set  up  menu  will  allow  the 
projector to be used for desktop front, ceiling front, desktop rear 
and ceiling rear installations (Fig. 9).
+12VUSB 1.1R/CrCONT ROL (RS2 32)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO O UTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0I
Fig. 9
To  activate  an  electric  motorised  screen  a  1  Volt  output  is 
provided at the rear of the projector.  This can be connected 
to  a  screen  interface  unit,  which  can  be  supplied  by  screen 
manufacturers (Fig. 10).
The output is activated (Voltage: 1 Vdc) when the projector is 
switched on and is de-activated (no Voltage output) when the 
projector is in stand-by mode.
Some  manufacturers  offer  screen-masking  systems  to  help 
frame the projected image and improve picture contrast. 
These systems can be connected to output  , at the rear of 
the projector (Fig. 11).
+12VUSB 1.1R/CrC ON TROL (RS2 32)GRAPHICS RGBC/YB/CbHVS-VID EOAUDIO OUTH DMI 1REMOTE32S-V IDEOMENUESCINPUT154
0I
For rear projection the screen must be translucent.
For  front  projection,  we  recommend  the  use  of  screens  with 
low gain specifications
+12VUSB 1.1R/CrCONT ROL (RS232)GRAPH ICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VI DEOMENUESCINPUT154
0I
The use of high gain screens should be avoided due to their limi-
ted viewing angle, which is undesirable for a large audience.
Preferably,  use  a  screen  with  black,  non-reflecting  borders, 
which will perfectly frame the projected image.
Avoid light shining directly on the screen during projection as 
this will reduce contrast and black level detail on the projected 
image.  For the true cinema experience best results are achie-
ved with little or no ambient light.
Furniture and other objects with reflecting surfaces, as well as 
light  coloured  walls  should  be  avoided,  as  they  are  likely  to 
interfere with the screen’s characteristics.
Fig. 11
Fig. 10 
						

							
10

5   SWITCHING ON AND OFF THE PROjECTOR
ACAUTION: Connect the projector to a power supply with a 
nominal voltage within the following values:  100-240 Vac, 
50/60 Hz. It must be earthed (Fig. 12).
GRAPHICS RGBHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESCINPUT
1
5
4
0I
Power Switch:Position I: OnPosition 0: Off
FusedPower Socket
Power Plug
Fig. 1
Upon switch on (in position I) the projector will initialise (red and 
green LEDs on).
Followed by stand-by mode (red LED on)  (Fig. 13).
HDMI 1MENU
ESCINPUT
5
HDMI 26
0I
Switch on from Stand-By 
By remote control: press   
By keyboard: press 
CONTROL (RS232)
GRAPHICS RGB
B/CbHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESC
1
5
4
Fig. 14
When switching on from stand-by, the projector will turn on the 
lamp; after a brief warm up period the image will be displayed 
(green LED on).The input automatically selected will be the last 
one memorised prior to switch off (Fig. 14).
You  may  experience  difficulties  switching  on  the  projector 
shortly after switching off: the lamp may fail to come on as it 
is too hot.
Fig. 13