Sim2 Multimedia C3x 1080 Projector User Manual

4606230000
proc3
user and installation manual 

2
c3X 1080
MENU SOURCE
ESC 
Sets the unit to stand-by.
Activates the On Screen Display menus and allows navigation though the various pages.
▲,▼,◀,▶
Navigates between the On Screen Display menus and parameter settings.
Calls up the  Source Selection menu.
Deactivates the On Screen Display
1  REMOTE CONTROL AND KEYPAD
KEYS 0-9Select the sources directly. Switches on the panel from Standby.
STAND-BY / ONSets the panel to stand-by .
ESCAPEDeactivates the On Screen Display.
UP/DOwN/LEfT/RighT ARROw...

3
c3X 1080
Different input signal resolutions can be adapted to match the specified screen  resolution  without  loss  of  image  quality,  thanks  to  a  generous selection of preset aspect ratios, some of which are user definable.
All picture adjustments can be made with the remote control interac-ting with a simple menu-activated On Screen Display; alternatively, the projector can be controlled by a domestic automation system by its serial port or by USB port.
The appliance has been subjected to...

4
c3X 1080
CAUTiONTo reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing th\
e top cover of the projector.For technical assistance refer to trained personnel authorised by the man\
ufacturer.
Read all chapters of this manual carefully before switching on the projector. This manual provides basic instructions for using the C3X1080 system. installation, preliinary adjustments and procedures that necessitate the removal of the top cover and contact with...

5
c3X 1080
1 
5 
6+12V
USB 1.1 R/Pr
CONTROL (RS232) GRAPHICS RGB
C/Y
B/Pb
HV S-VIDEO
AUDIO OUT
HDMI 1
REMOTE
3
2S-VIDEO
MENUESC
SOURCE14
O
I
HDMI 2 MENU
119
8
12
10
15
16
17
13
14
18
19
14
2
3
7
•  
Read this manual carefully and keep it in a safe place for future consultation. This  manual  contains  important  information  on  how  to install  and  use  this  equipment  correctly.  Before  using  the equipment, read the safety prescriptions and instructions carefully. Keep the manual for future...

6
c3X 1080
•  Changing the fuses.
 Before changing the fuse disconnect the unit from the 
mains power supply.
 The  fuse  compartment  is  next  to  the  power  supply  con-
nector (Fig. 3). Remove the fuse holder (2) with a flat head 
screwdriver and replace the fuse (3). Fit a new spare fuse 
(4). Use only T 5A H fuses.
Fig.3
•  Be careful with cables.
 Make certain cables are routed so that people will not be 
impeded or tripped up.
 Keep all cables away from children. 
 Install the unit as close to...

7
c3X 1080
1
2
3
4
3  UNPACKiNg
To remove the C3X1080 system from its carton follow 
the diagrams (Fig. 4).
Keep  the  carton  for  use  when  transporting  or  ship-
ping the unit.
Fig.4
CONTENTS Of PACKAgE
1
1
2
3
6
4
5
Fig.5
1) Projector
2) Remote control 
3) Four 1.5V AAA batteries (for remote control)
4) Power cables (EU, UK, USA) for the projector
5) User manual
6) Live Color Calibration Cd Rom
If anything is missing, immediately inform your dealer.   

8
c3X 1080
Position the projector on a stable, suitable platform or utilise the 
optional bracket for a fixed ceiling installation.
wARNiNg:  if  using  the  ceiling  mount  bracket,  scrupulously 
observe  the  safety  instructions  included  with  the  bracket 
itself. if  using  a  bracket  other  than  that  supplied  by  SiM2 
Multimedia, make sure that the projector is at least 65 mm 
below the ceiling and that the bracket does not obstruct the 
air vents (intake and outlet).
If the projected image...

9
c3X 1080
To  activate  an  electric  motorised  screen  a  12  Volt  output  is 
provided at the rear of the projector (Fig. 10).
The output is activated (Voltage: 12 Vdc) when the projector is 
switched on and is de-activated (no Voltage output) when the 
projector is in stand-by mode.
You can also use black motirised curtains to delimit the screen 
when the projected image aspect ratio changes (Fig. 11a). This 
option is controlled via the output at the rear of the projector.
 
For rear projection...

10
c3X 1080
5   SwiTChiNg ThE PROJECTOR ON AND Off
wARNiNg: Connect the projector to a power supply with a 
nominal voltage within the following values: 110-240 V AC, 
50/60 hz. it must be earthed (f ig. 12).
GRAPHICS RGBHV
S-VIDEO
AUDIO OUT
HDMI 1
REMOTE2 S-VIDEO
MENUESC
INPUT1 
5 
4 
0 
I 
HDMI 15
Power Switch:
Position I: On
Position 0: Off
Fused
Power Socket
     
Power Plug
 
Fig. 12
In position  i the projector will initialise itself  (red and green leds 
on) and then goes into standby mode (red...