Sigarms Sig Pro SP2009, SP2022, SP2340 Instructions Manual

11
Field Stripping
Before you take the pistol apart, make sure it's unloaded. 
This is essentialfor your safety and the safety of others.
Field strip the pistol as follows:
Figure A

Press the magazine catch. 

Remove the magazine.
Figure B

Pull back the slide (4) as far as it will go and hold it in the open position by  
pushing up the slide catch lever (17) with your thumb.

Check carefully to ensure that the chamber is empty and the magazine well
is clear (see below).
OM-SIGPRO-USA 6-2005.qxp...

12
Figure C

Take frame and slide in your right hand.

Pull slide (4) back slightly to release slide catch lever (17).

Allow slide to move forward slightly (about 1/8”) until the slide recess notch 
lines up with the tab on the slide catch lever (4b).

Using your left hand, press on the slide catch lever shaft from the right side 
of the pistol and remove the slide catch lever from the left side of the pistol.
Figure D

Hold the slide firmly and allow it to move forward slowly. 

Now slip the complete...

13
Figure E

Push the recoil spring guide (2) carefully forward and to one side or lift off
and remove recoil spring (3) and recoil spring guide (2) from slide (4).
Recoil spring is under tension - use care to control spring during removal!
Figure F
Remove the barrel (1) from the slide (4).
Figure G

Grip removal - press retaining lug (45a) to remove grip plate (45).

The grip plate should only be removed if weapon is extremely dirty (water, 
sand, mud, etc) or if changing between grip sizes....

14
User Disassembly (Field Stripping)
The field stripped pistol is shown in Figure Hbelow.  This level of disassembly 
is qute sufficient to allow for cleaning & lubrication after shooting. Further 
disassembly should only be done by qualified gunsmiths and armorers.
Figure H
WARNING
DO NOT ATTEMPT TO DISASSEMBLE YOUR PISTOL
BEYOND THE POINT EXPLAINED IN THIS MANUAL. 
OM-SIGPRO-USA 6-2005.qxp  6/1/2005  8:54 AM  Page 14 

15
Assembling the pistol
To reassemble the pistol after cleaning, simply reverse the disassembly steps.

Check that there is no foreign matter inside the pistol.

Push the grip plate back on frame from below until the grip plate retaining notch 
snaps into place.

With the slide upside down (sights down), place the barrel (1) in the slide (4).

Place the recoil spring (3) back on the recoil spring guide (2).

Insert recoil spring & guide assembly into slide.  Ensure the button on the 
flat end of the...

16
Caring for your Pistol
WARNING
BEFORE PERFORMING ANY CLEANING OR MAINTENANCE, 
MAKE SURE THE PISTOL IS COMPLETELY UNLOADED. 
THIS INCLUDES THE MAGAZINE AND CHAMBER.
Follow these instructions and your SIG SAUER pistol will remain in excellent
condition even after years of hard service.
NOTE: Your SIG SAUER pistol comes from the factory with a light coating of
protective grease and oils. Before you fire the pistol, you should disassemble,
clean and lubricate it as recommended on this page.
WARNING...

17
Transport and Storage
When transporting your pistol, keep it unloaded for your safety and for the 
safety of others. Know and comply with all laws governing the transport of
firearms in your locality. When storing your pistol, keep it unloaded and 
separated from ammunition, under lock and key and out of the reach of 
children and other inexperienced or unauthorized persons. 
Returning your Firearm 
When you return a pistol to the SIGARMS Inc. Service Department, here's
what to do: 
1.  The first...

18
Sights
The SIG SAUER pistol is equipped with drift adjustable fixed sights which have
proven their worth under severe conditions. The sights consist of a rear sight and a
front sight blade, designed and dimensioned to ensure rapid target acquisition even
when visibility is poor. You can adjust the sights as follows:
Windage (left/right):Change windage by moving the rear sight either to the left
or right in its dovetail. When you do this, follow the rear sight rule: Move the rear
sight in the direction...

19
Parts
Before you order any parts, please be advised that while most gunsmiths and
armorers are perfectly capable of repairing your firearm, we can't vouch for any
individual's skill or workmanship. Remember, unauthorized adjustments or
parts replacement can void your service policy. Your SIG SAUER pistol is a
precision instrument and some replacement parts may require a trained gunsmith
or armorer to ensure proper operation. Don't take chances; if your firearm ever
needs service, simply...

20
This instruction manual should always accompany this pistol and be 
transferred with it upon change of ownership.
Service Policy
If you have questions concerning the performance or servicing of your pistol,
please write or call:SIGARMS Inc.
Attention: Service Department
18 Industrial Drive
Exeter, NH 03833   USA
Phone: 603 772-2302  Fax: 603 772-9082
IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS
FOR OPERATING YOUR PISTOL, IT IS YOUR RESPONSIBILITY
TO CALL OUR SERVICE DEPARTMENT: Phone # 603 772-2302...