Sigarms Sig Auer Pistol P220 Instructions Manual

							11
Field Stripping
Before you take the pistol apart, make sure it's unloaded. This is essential
for your safety and the safety of others.
Field strip the pistol as follows:
Figure A

Press the magazine catch (43). Remove the magazine (51).
4
1618
43
51
Figure B

   Pull back the slide (4) as far as it will go and hold it in the open
position by pushing up the slide catch lever (18) with your thumb.

Check carefully to ensure that the chamber is empty and the magazine well
is clear.

Turn the take-down lever (16) to a vertical (6 o'clock) position. 
						

							12
Figure C

  Pull back the slide (4) slightly to disengage the slide catch lever (18). Hold
the slide firmly and allow it to glide forward gently. Now slip the complete
assembly, comprising slide (4), barrel (1), recoil spring and guide, forward
and off the frame (15).
Figure D

  Remove the recoil spring (3) and guide (2), taking care to control the release
of spring tension while pointing the assembly away from your body and in a
safe direction.
Figure E

  Remove the barrel (1) from the slide (4).

  The field stripped pistol is shown in Figure F.  Field stripping is quite
sufficient to allow cleaning after shooting. Further dismantling is a job for
qualified gunsmiths and armorers only.
1841
15
2 & 3
41 
						

							13
Assemble the pistol as follows:
Insert the barrel (1) into the slide (4); fit the recoil spring (3) and guide (2) into
place. If the recoil spring and guide were separated during stripping, ensure
that the narrower end of the spring is slipped over the guide first. During
spring compression, point the assembly away from your body. Slip the assem-
bled slide system onto the frame (15) until it contacts the end stop, and hold it
in place with the slide catch lever (18). Now, push up the take-down lever (16).
To close the slide, thumb down the slide catch lever (18). Decock the hammer
(29) with decocking lever (40)*. Insert the magazine.
* There's no decocking lever on the DAO. See page 7 of this manual.
4
1
2
3
15
164018
29
Figure F 
						

							14
Caring for your Pistol
WARNING
BEFORE PERFORMING ANY CLEANING OR MAINTENANCE,
MAKE SURE THE PISTOL IS COMPLETELY UNLOADED. 
THIS INCLUDES THE MAGAZINE AND CHAMBER.
Follow these instructions and your SIG SAUER pistol will remain in excellent
condition even after years of hard service.
NOTE: Your SIG SAUER pistol comes from the factory with a light coating of
protective grease and oils. Before you fire the pistol, you should disassemble,
clean and lubricate it as recommended on this page.
WARNING
BEFORE PERFORMING ANY DISASSEMBLY, MAKE SURE YOU
ARE WEARING EYE PROTECTION
Barrel and chamber:
Clean the barrel and the chamber from the rear with a quality cleaning solvent,
using a cleaning rod and brush of the correct caliber. Never clean the barrel
from the muzzle end. Wipe the interior and exterior of the barrel free of all
residue. Lightlylubricate the barrel, inside and out, with a quality lubricant
designed for firearms.
Breech face and locking insert:
Use a small nylon bristle brush to thoroughly clean these areas.
External metal surfaces:
After each use, wipe all metal surfaces with a cloth lightly soaked with a lubri-
cant preservative. This will remove any foreign material and preserve the fin-
ish of the pistol. Lightly lubricate the recoil spring (3), recoil spring guide (2)
and frame rails before reassembling the pistol.
NOTE:Some cleaning solvents may be harmful to the finish of your pistol.
Read the solvent manufacturer's product use instructions and warning labels
before using.
IMPORTANT
It is your responsibility to maintain your pistol, if rust appears in the bore, 
the barrel should be replaced.
PRIOR TO SHOOTING MAKE SURE THE BORE IS DRY. 
						

							15
Transport and Storage
When transporting your pistol, keep it unloaded for your safety and for the 
safety of others. Know and comply with all laws governing the transport of
firearms in your locality. When storing your pistol, keep it separated from
ammunition, under lock and key and out of the reach of children and other
inexperienced or unauthorized persons. 
Returning your Firearm 
When you return a pistol to the SIGARMS Inc. Service Department, here's
what to do: 
1.  Make sure that the chamber and magazine(s) are unloaded and that no 
ammunition is included. 
2.  Package the firearm securely to prevent damage. Enclose a letter which 
includes your name, street address, daytime phone number, pistol model 
and serial number, and a detailed description of the problem you have expe-
rienced or the work you want performed. With the exception of extra maga-
zines, do not include cases, scopes, mounts or other accessories. 
If repairs are to be done under warranty, enclose copy of sales receipt. 
3.  Generally, an individual may ship firearms to the manufacturer for repair or 
service. Some states and localities, however, prohibit this. If you live in 
such an area, the firearms must be shipped by and returned to a Federally 
Licensed Firearms Dealer. 
4.  Individuals must ship handguns via UPS.  Federal law prohibits persons 
who do not possess a Federal Firearms License from shipping a handgun 
via the U.S. Postal Service. (Note: Any shipment of firearms outside of the 
USAborders is subject to the valid law of the specific country, which you 
must strictly follow.) 
5.  Ship your firearms insured and prepaid (we don't accept collect 
shipments) to:
SIGARMS Inc. 
Attention: Service Department Corporate Park 
18 Industrial Drive
Exeter, NH 03833 
USA 
						

							16
Sights
The SIG SAUER pistol is equipped with drift adjustable fixed sights which
have proven their worth under severe conditions. The sights consist of a rear
sight and a front sight blade, designed and dimensioned to ensure rapid target
acquisition even when visibility is poor. You can adjust the sights as follows:
Windage:Change windage by moving the rear sight either to the left or right
in its dovetail. When you do this, follow the rear sight rule: Move the rear
sight in the direction you want the group to go. Moving the rear sight 0.020"
in the dovetail changes the point of impact by approximately 3" at 25 yards.
(Note:SIGARMS has available a Combination Sight Pusher tool which makes
it easier to adjust and change sights.)
Elevation:There are different height combinations available for the front and
rear sights. The sights are numbered according to their height. You can change
elevation by changing either the rear or front sight. It's easier if you change the
rear sight first. Each rear sight change will move the impact of the bullet
approximately 2" at 25 yards. Each front sight change will move the impact of
the bullet approximately 1" at 25 yards.
Remember, a higher rear sight will raisethe impact of the bullet; a higher front
sight will lowerthe impact of the bullet.
Sight Options
Front Sight  Rear Sight
Number  Height  Number  Height
05  6.01 mm  05  5.52 mm
06  5.88 mm  06  5.80 mm
07  5.74 mm  07  6.07 mm
08  5.60 mm  08  6.35 mm
09  5.46 mm  09  6.62 mm
10  6.90 mm 
						

							17
Parts
Before you order any parts, please be advised that: while most gunsmiths and
armorers are perfectly capable of repairing your firearm, we can't vouch for any
individual's skill or workmanship. Remember, unauthorized adjustments or
parts replacement can void your service policy. Your SIG SAUER pistol is a
precision instrument and some replacement parts may require a trained gunsmith
or armorer to ensure proper operation. Don't take chances; if your firearm ever
needs service, simply return it to SIGARMS Inc. Remember, always specify
MODEL, CALIBERand SERIAL NUMBERof your pistol when ordering
parts.
If you order a part without returning the pistol to SIGARMS Inc., you're respon-
sible for ensuring that the part supplied is correct for your particular pistol and
that it is properly installed and fitted by a qualified gunsmith or armorer.
Inspection and Maintenance
Even the best of pistols, like fine automobiles, require periodic maintenance
and inspection. This may reveal a need for adjustment or repair. Even if your
pistol seems to be working well, don't take chances... have it checked annually
by a qualified gunsmith or armorer.
If you notice any mechanical malfunction, STOP using the firearm. UNLOAD
it and take it to a qualified gunsmith or armorer immediately for a thorough
examination. Similarly, if water, sand, or other debris enters the mechanism,
field strip the pistol immediately and thoroughly clean it. Failure to keep your
pistol cleaned, lubricated and in proper working order could lead to serious bodi-
ly injury or property damage.
SIGARMS Inc. CANNOT BE RESPONSIBLE FOR THE
FUNCTIONING OF ANY FIREARM WHICH HAS BEEN
ALTERED FROM FACTORY SPECIFICATIONS
WARNING
DO NOT ATTEMPT TO DISASSEMBLE YOUR PISTOL BEYOND THE
POINT EXPLAINED IN THIS MANUAL.  THIS SHOULD BE DONE 
ONLY AT THE FACTORY.
Some of the components are installed under great spring pressure
requiring special tools and fixtures for disassembly. 
						

							18
This instruction manual should always accompany this pistol and be 
transferred with it upon change of ownership.
Service Policy
If you have questions concerning the performance or servicing of your pistol,
please write or call:SIGARMS Inc.
Attention: Service Department
18 Industrial Drive
Exeter, NH 03833   USA
Phone: 603 772-2302  Fax: 603 772-9082
IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS
FOR OPERATING YOUR PISTOL, IT IS YOUR RESPONSIBILITY
TO CALL OUR SERVICE DEPARTMENT: Phone # 603 772-2302
BEFORE USING YOUR FIREARM.
Warranty Statement
Based on Magnuson-Moss Warranty Act, SIGARMS Inc. offers no express
warranty on their product line. However, SIGARMS Inc. recognizes its
obligations concerning service to owners of SIGARMS products.
SIGARMS Inc. stands behind its products and will continue to provide ser-
vice to their product line as they have over the years. SIGARMS Inc. prod-
ucts will be serviced for a period of one year from date of retail purchase,
for defects in materials or workmanship, at no charge to the purchaser. Be
sure to retain your sales slip as proof of purchase date when making a claim.
WARNING
Always use the decocking leverto decock your SIG SAUER pistol.
This is the only way to safely lower the hammer from the cocked position
and prevent an accidental discharge.
This warning applies to all pistols with decocking levers. The positive
way to safely lower the hammer is by use of the decocking lever.
Never lower the hammer by pulling the trigger and attempting to ease
the hammer forward manually. Manually lowering the hammer is danger-
ous and prevents full application of the pistol's safety features.
The decocking lever is the only proper means of lowering the hammer
and assuring that the hammer rests in the intercept notch.
Again, DO NOT THUMB THE HAMMER DOWN:the consequence
can be serious injury or death - only and ALWAYS use the
decocking lever! 
						

							19
Specifications SIG SAUER P220 & P245
Mechanically-Locked, Recoil-Operated, Semiautomatic Pistol
Trigger:Double-Action/Single-Action or Double-Action Only
4 Point Safety System:1. Patented automatic firing-pin lock
2. Decocking Lever (DA/SA Only)
3. Safety Intercept Notch
4. Disconnector
P220 P245
Caliber  .45 ACP .45 APC
Length, overall  7.8"                 7.28˝
Height, overall  5.6"                 5.0˝ 
Width, overall  1.4"                 1.34˝
Barrel length  4.4"  3.9˝
Rifling twist  1 in 16"  1 in 16˝
Rifling grooves  6 6
Sight radius  6.3"  5.7˝
Weight, w/o magazine  27.8 oz.  27.5 oz.
Weight, empty magazine  2.6 oz.  2.5 oz.
Trigger pull weight  DA 10 Ibs.,       DA 10 lbs.
SA 4.5 Ibs.       SA 4.5 lbs.
Magazine capacity  7 rounds          6 rounds
8 rounds 
(optional)
All weights and dimensions are approximate
Specifications subject to change without notice 
						

							20
Specifications - SIG SAUER P225
Mechanically Locked, Recoil-Operated, Semiautomatic Pistol
Trigger:Double-Action/Single-Action or Double-Action Only
4 Point Safety System:1. Patented automatic firing-pin lock
2. Decocking Lever (DA/SA Only)
3. Safety Intercept Notch
4. Disconnector
Caliber  9mm Luger (Parabellum)
Length, overall  7.1"
Height, overall  5.2"
Width, overall  1.3"
Barrel length  3.9"
Rifling twist  1 in 10"
Rifling grooves 6
Sight radius  5.7"
Weight, w/o magazine  25.9 oz.
Weight, empty magazine 2.7 oz.
Trigger pull weight  DA 10 Ibs.,
SA 4.5 Ibs.
Magazine capacity  8 rounds
All weights and dimensions are approximate
Specifications subject to change without notice