Siemens Sx 66t096 Operating Instructions

							Rinse aiden
11
, Rinse aidRinse aid 
As soon as the rinse-aid refill  
indicator P is lit on the fascia, there 
is still a rinse-aid reserve of 1-2 rinsing  
processes. Refill with rinse aid. 
The rinse aid is required for stain-free  
utensils and clear glasses. Use only  
rinse aid for domestic dishwashers. 
Combined detergents with rinse-aid  
component may be used up to a water 
hardness of 21° dH (37° fH,  
26° Clarke, 3.7 mmol/l) only. If  
the water hardness is over 21° dH, 
rinse aid must be used. 
1. Open the dispenser 9* by pressing 
and lifting the plate on the cover.
2. Carefully pour rinse aid up  
to the max. mark in the filler opening. 3.
Close cover until it clicks shut.
4. To prevent excessive foam formation  
during the next rinse cycle, remove  
any rinse aid which has run over with  
acloth.
Setting amount of rinse aid 
The amount of rinse aid can be set from  
§ :‹‹  to  §:‹‡ . Please set rinse aid on 
§ :‹†  to obtain very good drying results 
( § :‹†  is already set in factory).
Change this setting, only if streaks  
(select lower setting) or water stains  
(select higher setting) are left on the  
utensils. 
1. Open the door.
2. Switch on ON/OFF switch  (.
3. Hold down programme button  # 
and press START button  ) until 
• :‹ .... is indicated on the digital 
display.
4. Release both buttons. 
The LED for button  # flashes and 
the digital display  8 displays the 
factory setting  •:‹… .
5. Press programme button  # until 
the factory set value  §:‹†  is 
indicated on the digital display  8.  
To change the setting: 
1. Press programme button 3.
Each time the button is pressed, the  
set value increases by one level;  
when the value of §:‹‡  has been 
reached, the display jumps back  
to §:‹‹  (off). 
2. Press START button ). 
The set value is saved. 
3. Close the door.



 
						

							enUtensils
12
Switching off rinse aid refill  
indicator 
If the rinse-aid refill indicator 
P is 
impaired (e.g. when using combined  
detergents containing rinse aid  
component), it can be switched off.

						

							Utensilsen
13
Unloading the dishwasher 
To prevent water from dripping off the  
upper basket onto the utensils in the  
lower basket, it is recommended  
to empty the appliance from the bottom 
up. 
Hot utensils are sensitive to shock!  
Therefore, when the programme ends,  
leave the utensils to cool down in the  
dishwasher until they can be handled. 
Note 
When the programme ends, water  
droplets can still be seen inside  
the appliance. This does not affect  
the drying of the utensils. 
Cups and glasses 
Top basket 
12 Pans
Bottom basket 
9
Tip 
Heavily soiled utensils (pans) should  
be placed in the bottom basket. The  
more powerful spray jet provides 
a better dishwashing result. 
Tip 
Other examples, such as the best way  
of loading your dishwasher, can  
be found on our homepage as a free  
download. The corresponding Internet  
address can be found on the back page  
of these instructions for use.
            
						

							enUtensils
14
Cutlery drawer 
Arrange the cutlery in the cutlery drawer  
1*
 as illustrated. Separately arranged 
utensils are easier to remove after 
washing. 
The drawer can be taken out. 
Depending on the model, you can fold  
down the side shelves to provide more  
room for taller items of cutlery. The front  
rows of prongs can be folded down  
to provide room for wider handles. 
Fo ld in g spikesFolding spikes *
* depending on model 
The spikes can be folded down to  
improve arrangement of pans, bowls  
and glasses. 
Small accessories holder *
Sm a ll a c c
es sor
ie s  ho ld er
* depending on model 
Light-weight plastic accessories, e.g.  
cups, lids, etc. can be held securely in  
the small accessories holder. 
Adjusting the height of the  
basket 
The height of the upper utensils basket  
12  can be adjusted in 3 stages to 
create more space either in the upper or  
lower basket.



 
  
						

							Detergenten
15
Appliance height 81.5 cm 
Appliance height 86.5 cm 
1.
Pull out the top basket  12 out. 
2. To lower  the basket, press in the left 
and then the right lever on the  
outside of the basket. In doing so,  
hold the sides of the basket along  
the upper edge to prevent it from  
suddenly dropping.
3. Toraise  the basket, hold the basket 
on the sides of the upper edge and  
lift it up.
4. Before re-inserting the basket again,  
ensure that it is at the  same height 
on both sides. Otherwise, the  
appliance door cannot be closed  
and the upper spray arm will not be 
connected to the water circuit. 
. DetergentDetergent
You can use tablets as well as powder  
or liquid detergents for dishwashers, but  
never use washing up liquid.  
The dosage can be individually adjusted  
with powder or a liquid detergent  
according to the degree of soiling.  
Tablets contain an adequately large  
amount of active ingredients  
for all cleaning tasks. Modern, powerful  
detergents predominantly use a low- 
alkaline formulation with phosphate  
and enzymes. Phosphates bond  
the lime in the water. Enzymes break  
down starch and remove protein.  
Phosphate-free detergents are less 
frequent. These have a slightly weaker  
lime bonding capacity and require  
a higher dosage. To remove coloured 
stains (e.g. tea, tomato sauce), oxygen- 
based bleaching agents are usually  
used. 
Note 
To ensure a good washing result,  
always follow the instructions  
on the detergent packaging! 
If you have further questions,  
we recommend that you contact  
the detergent manufacturers’ helpline. ãWarning –  Read and observe the 
safety information and instructions for  
use on the packaging for cleaning and  
rinsing agents.
Top basket Bottom 
basket
Setting 1 max. ø 16 cm 30 cm 
Setting 2 max. ø 18.5 cm 27.5 cm 
Setting 3 max. ø 21 cm 25 cm
Top basket Bottom basket
Setting 1 max. ø 18 cm 33 cm 
Setting 2 max. ø 20.5 cm 30.5 cm 
Setting 3 max. ø 23 cm 28 cm
 
						

							enDetergent
16
Adding detergent 
1.
If the detergent dispenser  92 is still 
closed, press the lock  9: to open 
the detergent dispenser. 
Pour detergent into the dry detergent  
dispenser 92 only (insert tablet flat, 
not on its edge).  
Dosage: see manufacturer’s  
instructions on the packaging. 
The graduated detergent  
dispenser 92 helps you add the 
correct amount of powder or liquid  
detergent. 
Usually 20 ml–25 ml are adequate  
for normal soiling. If using tablets,  
one tablet is adequate.
2. Close the cover on the detergent  
dispenser by sliding it up until the  
lock engages without difficulty. 
The detergent dispenser opens  
automatically at the optimum time  
depending on the programme.  
The powder or liquid detergent  
is distributed in the appliance and is  
dissolved, the tablet falls into  
the tablet collecting tray where it  
dissolves in doses. Tip 
If the utensils are only lightly soiled,  
slightly less than the indicated amount  
of detergent is usually adequate.  
Suitable detergents and care products  
can be purchased online  
via our website or via customer service  
(see back page). 
Combination detergent 
Apart from conventional detergents  
(Solo), a number of products are offered  
with additional functions. These  
products contain not only the detergent  
but also rinse-aid and salt replacement  
substances (3in1) and, depending  
on the combination (4in1, 5in1, etc.),  
additional components such as glass  
protection or stainless steel cleaner.  
Combination detergents function only  
up to a specific degree of hardness  
(usually 21°dH). Over this limit salt  
and rinse-aid must be added.  
As soon as combined detergents  
areused, therinse programme 
is adjusted automatically to ensure  
the best possible rinsing and drying  
result. ã Warning –  Do not place small parts 
for washing in the tablet collecting tray  
1B ; this prevents the tablet from 
dissolving evenly. ã Warning –  If you want to add more 
utensils after the programme  
has started, do  not use the tablet 
collecting tray 1B as a handle 
for the upper basket. The tablet could 
already be there and you will touch 
the partially dissolved tablet.



 
						

							Detergenten
17
Notes

						

							enOverview of programmes
18
/ Overview of programmesOverviewofprogrammes
The max. possible number of programmes is illustrated in this overview. 
The corresponding programmes and their arrangement can be found on the 
fascia.   Programme selection 
You can select a suitable programme  
according to the type of utensils and  
degree of soiling.
Type of utensils Type of soiling Programme Possible 
additional  
optionsProgramme sequence
pots and pans,  
non-sensitive  
utensils  
and cutlery very adhesive burned- 
in or dried-on food  
remnants containing  
starch or protein ¹ 
Auto 65° - 75°
all
Is optimised according  
to the soiling with the aid  
of sensors.
Á 
Auto 45° - 65° all
mixed utensils  
and cutlery part dried, common  
household food  
remnants Á 
Auto 45° - 65°
all
Is optimised according  
to the soiling with the aid  
of sensors.
â  / à
Eco 50° all Prerinse 
Clean 50° 
Intermediate rinse 
Final rinse 65°
Drying
sensitive utensils,  
cutlery,  
temperature- 
sensitive plastic  
and glasses
slightly adhesive,  
fresh food remnants É 
Auto 35° - 45°IntensivZone 
Express Wash/  
Speed Perfect  
(VarioSpeed) 
Energy Save 
Half load
Glossy drying Is optimised according  
to the soiling with the aid  
of sensors.
ñ  / ð
Quick 45° Glossy drying Clean 45° 
Intermediate rinse 
Final rinse 55°
all types  
of utensils
cold rinsing, 
intermediate cleaning ù
 / ø
Prerinse none Prerinse
 
						

							Additional optionsen
19
Information for test institutes 
Test institutes receive the information for  
comparability tests (e.g. according to  
EN60436).  
These are the conditions for conducting  
the tests, however these are not the  
results or consumption values.  
Request by e-mail to:
[email protected] 
The product number (E no.) and the  
production number (FD) are required  
which you can find on the rating plate  
9B
 on the appliance door. 
0 Additional optionsAdditional options
* depending on model 
Additional options can be set with  
the buttons  h.
Exp
re s
s W as h/ Spe ed Per
fe c
t ( V
ar io S pee
d)Ÿ  Express Wash/ Speed 
Perfect/ (VarioSpeed) * 
This function can reduce the running  
time by approx. 20% to 50% depending  
on the selected rinse programme. The  
change in the running time is indicated  
on the digital display 8. To obtain 
optimum cleaning results at a reduced  
running time, water and energy  
consumption are increased.
Ha lf
 lo ad§  Half load *
If you have only a few items to wash  
(e.g. glasses, cups, plates), you can  
switch to “half load”. This will save  
water, energy and time. It is  
recommended to put a little less  
detergent in the detergent dispenser  
than for a full load. ·
 Hygiene *
Hyg
ie ne
The temperature is increased during the  
cleaning process. This increases the  
hygiene status. This additional option is  
ideal for cleaning e.g. chopping boards 
and baby bottles. 
Ï  Intensive zone *
In
te nsiv
e z one
Perfect for a mixed load. You can wash  
very soiled pots and pans in the lower  
basket together with normally soiled  
utensils in the upper basket. The spray  
pressure in the lower basket is  
intensified, the rinsing temperature is  
increased slightly.  
ï  High gloss drying *
H
ig h
 g lo ss
 d r
yin g
By increasing the amount of water  
during the rinse cycle and extending the  
drying phase, stains are prevented and  
the drying result is improved. There is a  
slight increase in the energy  
consumption. Rinse aid is  
recommended for the high gloss drying  
function (even when using combination  
detergents). 
ß  
Ener g
y S aveEnergy Save *
Water and energy consumption can be  
reduced with the “Energy Save”  
function. The running time is extended  
for optimum cleaning and drying results.
 
						

							enOperating the appliance
20
1 Operating 
the appliance
Operating theappliance
Programme data 
The programme data (consumption  
values) can be found in the summary of  
instructions. They refer to normal  
conditions and the water hardness set  
value  •:‹… . Different influencing factors 
such as e.g. water temperature or line  
pressure may result in deviations.
Aq u
a s ens
orAqua sensor *
* depending on model 
The Aqua sensor is an optical  
measuring device (light barrier) which 
measures the turbidity of the rinsing  
water. 
The Aqua sensor is used according to  
the programme. If the Aqua sensor is  
active, “clean” rinsing water can be  
transferred to the next rinse bath and  
water consumption can be reduced by  
3–6 litres. If the turbidity is greater, the  
water is drained and is replaced with  
fresh water. In the automatic  
programmes the temperature and  
running time can also be adjusted to the  
degree of soiling. Zeolith drying 
The appliance features a Zeolith  
container Zeolith is a mineral which can  
store moisture and heat energy and  
release them again.  
During the washing step this heat  
energy is used to dry the mineral and 
heat up the rinsing water.  
During the drying phase moisture from  
the washing compartment is stored in  
the mineral and heat energy is released.  
This released heat energy is blown into  
the washing compartment with dry air.  
This accelerates and improves drying. 
These processes therefore save a great  
deal of energy. ã
Caution
Please ensure that the intake opening  
1J  is not obstructed and do not place 
any temperature-sensitive utensils in the  
lower basket at the rear right side above  
the blow opening 1R.
ã Warning – Risk of injury!
Do not touch the blow opening 1R. The 
blow opening becomes hot and,  
furthermore, any damage will result in 
a chargeable callout by customer  
service.