Siemens Sr 26t890 Operating Instructions

Fault, what to do?en
31
Coloured (blue, yellow,  
brown), difficult to remove  
to non-removable coatings  
in the appliance or on 
stainless steel utensils.
Film formation consisting  
of ingredients from vegetables  
(e.g. cabbage, celery, potatoes,  
noodles, ...) or the tap water (e.g.  
manganese). Can be partly removed with machine  
cleaner or by mechanical cleaning. Coatings  
are harmless.
Film formation caused by metallic  
components on silver or  
aluminium utensils. Can be partly removed...

enFault, what to do?
32
Rust spots on the cutlery. Cutlery not adequately rust-
resistant. Knife blades are  
frequently more severely  
affected. Use corrosion-resistant cutlery.
Cutlery will also rust if rusting 
parts are rinsed at the same time 
(pan handles, damaged utensil  
baskets, etc.). Do not wash rusting parts.
Salt content in the rinsing water 
too high, as salt dispenser lock  
not fastened firmly or salt was 
spilled while being refilled. Fasten salt dispenser lock firmly or remove...

Fault, what to do?en
33
 
Appliance stops  
in the programme or  
programme is interrupted.
Door not closed properly. Close the door. 
Do not place utensils or fragrance  
dispenser in the tablet collecting 
tray. 
Top basket presses against inner  
door and prevents door from  
being closed securely. Check whether rear panel is being pressed  
in, e.g. by socket or by hose holder which 
has not been removed.
Power and/or water supply  
interrupted. Restore power and/or water supply.
Filling valves...

enCustomer service
34
4 Customer serviceCustomer service
If you are unable to rectify the fault,  
please contact your customer service.  
We always find a suitable solution, even  
to avoid unnecessary visits  
by technicians. Contact information  
for your nearest customer service can  
be found on the back of these  
instructions for use or on the enclosed  
customer service list. When calling,  
please state the appliance number (E- 
Nr. = 1) and the production number  
(FD = 2) which can be found on...

Installation and connectionen
35
Safety instructions 
Please follow the safety instructions  
under “Installation”.  
Delivery 
Your dishwasher has been checked  
thoroughly in the factory to ensure that it  
is in working order. This may cause  
small water stains. These will disappear  
after the first wash cycle. 
Technical specifications 
Weig ht: 
max. 45 kg
Voltage: 
220–240 V, 50 Hz or 60 Hz 
Connected load: 
2.0–2.4 kW 
Fuse: 
10/16 A (UK 13A)
Power input:
switched off 0.1 W 
not switched off 0.1...

enInstallation and connection
36
Fresh water connection 
1.
Connect the fresh-water connection  
to the tap according to the  
installation instructions with the  
enclosed parts. 
Ensure that the fresh-water  
connection is not kinked, crushed or  
twisted.
2. When replacing the appliance,  
always use a new water supply hose.
Water pressure: 
at least 0.05 MPa (0.5 bar), maximum  
1 MPa (10 bar). At a higher water  
pressure: connect pressure-reducing  
valve ahead. 
Inlet rate: 
minimum 10...

Installation and connectionen
37
To change the setting: 
1.
By pressing the 3 button, you can 
switch the hot water setting off ‘:‹‹  
or on ‘:‹‚ .
2. Press START button h.
The set value is saved. 
Electrical connection


enInstallation and connection
38
Transportation 
Empty the dishwasher and secure loose  
parts. 
Drain the appliance according to the  
following steps: 
1.
Turn on the tap.
2. Close the door.
3. Switch on ON/OFF switch (.
4. Select programme with the highest  
temperature. 
The expected programme duration is  
indicated on the numerical display   
)* .
5. Press START button  h.
Programme sequence starts.
6. After approx. 4 minutes press the  
START button h until  ‹:‹‚  is 
indicated on the digital...

      



   



DownloadedfromDishWasherManualcomManuals 

 
 

 
 


 

 
 
 
 
 



 
 
 






 
 
 


 

 


*9000870252* 
9000870252
 en (9302) 440MG