Siemens Sr 26t291 Operating Instructions

							Rinse aiden
11
Using special salt 
Always refill with special salt  
immediately before switching on the  
appliance. This ensures that overrun  
special salt solution is immediately 
washed out and does not corrode the  
rinsing tank. 
1.
Open the screw-type cap of the  
compartment  1R.
2. Fill the tank with water (only required  
when switching on the appliance for 
the first time). 
3. Then add dishwasher salt  (not table 
salt or tablets) . 
The water is displaced and runs out. 
As soon as the salt refill indicator  @ 
on the fascia is lit, top up the salt. 
* depending on model 
Using detergents with salt  
component
De ter
ge n
ts  wit h sa
lt  c
ompo nent
If combined detergents with a salt  
component are used, salt can usually be  
omitted up to a water hardness of  
21° dH (37° fH, 26° Clarke, 3.7 mmol/ 
l). If the water hardness is over 21° dH,  
special salt must be used. Switching off salt refill  
indicator/water softening 
system
Sw
it c h
in g
 o f
f w ater
 s o
ft e
nin g sys t
em
If the salt refill indicator  @ is impaired 
(e.g. when using combined detergents  
containing salt component), it can be  
switched off.

						

							enRinse aid
12
1.
Open the dispenser 1j by pressing 
and lifting the plate on the cover.
2. Carefully pour rinse aid up  
to the max. mark in the filler opening.
3. Close cover until it clicks shut.
4. To prevent excessive foam formation  
during the next rinse cycle, remove  
any rinse aid which has run over with 
acloth.
Setting amount of rinse aid 
The amount of rinse aid can be set from  
§ :‹‹  to  §:‹‡ . Please set rinse aid on 
§ :‹…  to obtain very good drying results 
( § :‹…  is already set in factory).
Do not change the amount of rinse aid  
unless streaks (select lower setting)  
or water stains (select higher setting)  
are left on the utensils. 1.
Close the door.
2. Switch on ON/OFF switch (.
3. Hold down programme button # 
and press START button h 
until •:‹ ... is indicated on the digital 
display.
4. Release both buttons. 
The LED for button # flashes 
and the digital display )* displays 
the factory setting •:‹… .
5. Press programme button # until 
the factory set value  §:‹…  
is indicated on the digital  
display )*.
To change the setting: 
1. Press programme button 3.
Each time the button is pressed,  
the set value increases by one level;  
when the value of §:‹‡  has been 
reached, the display jumps back  
to §:‹‹  (off). 
2. Press START button h. 
The set value is saved. 
Switching off rinse aid refill  
indicator 
If the rinse-aid refill indicator  H is 
impaired (e.g. when using combined  
detergents containing rinse aid  
component), it can be switched off.

						

							Utensilsen
13
- UtensilsUtensils
Not suitable

						

							enUtensils
14
Cups and glasses 
Top basket 
12
Pans
Bottom basket  1b Tip 
Heavily soiled utensils (pans) should  
be placed in the bottom basket. The  
more powerful spray jet provides  
a better dishwashing result. 
Tip 
Other examples, such as the best way  
of loading your dishwasher, can  
be found on our homepage as a free  
download. The corresponding Internet  
address can be found on the back page  
of these instructions for use. 
Cutlery drawer 
Arrange the cutlery in the cutlery drawer  
1*
 as illustrated. Separately arranged 
cutlery is easier to remove after  
washing. 
The drawer can be taken out.
   
						

							Utensilsen
15
F
old ing
 s p
ik esFolding spikes *
* depending on model 
The spikes can be folded down to  
improve arrangement of pans, bowls  
and glasses. 
Small accessories holder *
Sm a ll a c c
es s
or ie s ho ld er
* depending on model 
Light-weight plastic accessories, e.g.  
cups, lids, etc. can be held securely in  
the small accessories holder. Adjusting the height of the  
basket 
The height of the upper utensils basket  
12
 can be adjusted in 3 stages to 
create more space either in the upper or  
lower basket. 
Appliance height 81.5 cm 
1. Pull out the top basket  12 out. 
2. To lower  the basket, press in the left 
and then the right lever on the  
outside of the basket. In doing so,  
hold the sides of the basket along 
the upper edge to prevent it from  
suddenly dropping.
3. To raise  the basket, hold the basket 
on the sides of the upper edge and  
lift it up.
4. Before re-inserting the basket again,  
ensure that it is at the  same height 
on both sides. Otherwise, the  
appliance door cannot be closed 
and the upper spray arm will not be  
connected to the water circuit. 
 Top basket Bottom 
basket
Setting 1 max. ø 14 cm 30 cm 
Setting 2 max. ø 16 cm 28 cm
Setting 3 max. ø 19 cm 25 cm
  
						

							enDetergent
16
. DetergentDetergent
You can use tablets as well as powder  
or liquid detergents for dishwashers, but  
never use washing up liquid.  
The dosage can be individually adjusted  
with powder or a liquid detergent  
according to the degree of soiling.  
Tablets contain an adequately large  
amount of active ingredients  
for all cleaning tasks. Modern, powerful  
detergents predominantly use a low- 
alkaline formulation with phosphate  
and enzymes. Phosphates bond  
the lime in the water. Enzymes break  
down starch and remove protein.  
Phosphate-free detergents are less 
frequent. These have a slightly weaker  
lime bonding capacity and require  
a higher dosage. To remove coloured 
stains (e.g. tea, tomato sauce), oxygen- 
based bleaching agents are usually  
used. 
Note 
To ensure a good washing result,  
always follow the instructions  
on the detergent packaging! 
If you have further questions,  
we recommend that you contact  
the detergent manufacturers’ helpline. ãWarning –  Read and observe the 
safety information and instructions for  
use on the packaging for cleaning and  
rinsing agents. Adding detergent 
1.
If the detergent dispenser  9 is still 
closed, press the lock  9* to open 
the detergent dispenser. 
Pour detergent into the dry detergent  
dispenser 9 only (insert tablet flat, 
not on its edge).  
Dosage: see manufacturer’s  
instructions on the packaging. 
The graduated detergent  
dispenser 9 helps you add the 
correct amount of powder or liquid  
detergent. 
Usually 20 ml–25 ml are adequate  
for normal soiling. If using tablets,  
one tablet is adequate.
2. Close the cover on the detergent  
dispenser by sliding it up until the  
lock engages without difficulty. 
The detergent dispenser opens  
automatically at the optimum time  
depending on the programme.  
The powder or liquid detergent  
is distributed in the appliance and is  
dissolved, the tablet falls into  
the tablet collecting tray where it  
dissolves in doses.



 
						

							Detergenten
17
Tip 
If the utensils are only lightly soiled,  
slightly less than the indicated amount  
of detergent is usually adequate.  
Suitable detergents and care products  
can be purchased online  
via our website or via customer service  
(see back page).  
Combination detergent 
Apart from conventional detergents  
(Solo), a number of products are offered  
with additional functions. These  
products contain not only the detergent  
but also rinse-aid and salt replacement  
substances (3in1) and, depending  
on the combination (4in1, 5in1, etc.),  
additional components such as glass  
protection or stainless steel cleaner.  
Combination detergents function only  
up to a specific degree of hardness  
(usually 21°dH). Over this limit salt  
and rinse-aid must be added.  
As soon as combined detergents  
areused, therinse programme 
is adjusted automatically to ensure  
the best possible rinsing and drying  
result. ã
Warning –  Do not place small parts 
for washing in the tablet collecting tray  
1B ; this prevents the tablet from 
dissolving evenly.
ã Warning –  If you want to add more 
utensils after the programme 
has started, do  not use the tablet 
collecting tray 1B as a handle 
for the upper basket. The tablet could 
already be there and you will touch 
the partially dissolved tablet. Notes

						

							enOverview of programmes
18
/ Overview of programmesOverviewofprogrammes
The max. possible number of programmes is illustrated in this overview. 
The corresponding programmes and their arrangement can be found on the 
fascia.   
Programme selection 
You can select a suitable programme  
according to the type of utensils and 
degree of soiling.
Type of utensils Type of soiling Programme Possible 
additional  
optionsProgramme sequence
pots and pans,  
non-sensitive  
utensils  
and cutlery very adhesive burned- 
in or dried-on food  
remnants containing  
starch or protein ¹ 
Auto 65° - 75°
all
Is optimised according  
to the soiling with the aid  
of sensors.
Á 
Auto 45° - 65° all
mixed utensils  
and cutlery part dried, common  
household food  
remnants Á 
Auto 45° - 65°
all
Is optimised according  
to the soiling with the aid  
of sensors.
â  / à
Eco 50° all Prerinse 
Clean 50° 
Intermediate rinse 
Final rinse 65°
Drying
sensitive utensils,  
cutlery,  
temperature-
sensitive plastic  
and glasses
slightly adhesive,  
fresh food remnants É 
Auto 35° - 45°IntensivZone 
Express Wash/  
Speed Perfect  
(VarioSpeed) 
Half load
Extra drying Is optimised according  
to the soiling with the aid  
of sensors.
ñ  / ð
Quick 45° Extra drying Clean 45° 
Intermediate rinse
Final rinse 55°
all types  
of utensils
cold rinsing, 
intermediate cleaning ù
 / ø
Prerinse none Prerinse
 
						

							Additional optionsen
19
Information for test institutes 
Test institutes receive the information for  
comparability tests (e.g. according to  
EN60436).  
These are the conditions for conducting  
the tests, however these are not the  
results or consumption values.  
Request by e-mail to:
[email protected] 
The product number (E no.) and the  
production number (FD) are required  
which you can find on the rating plate  
92
 on the appliance door. 
0 Additional optionsAdditional options
* depending on model 
Additional options can be set with  
the buttons  `.
Exp
re s
s W as h/ Spe ed Per
fe c
t ( V
ar io S pee
d)Ÿ  Express Wash/ Speed 
Perfect/ (VarioSpeed) * 
This function can reduce the running  
time by approx. 20% to 50% depending  
on the selected rinse programme. The  
change in the running time is indicated  
on the digital display )*. To obtain 
optimum cleaning results at a reduced  
running time, water and energy  
consumption are increased.
Ha lf  lo ad§  Half load *
If you have only a few items to wash  
(e.g. glasses, cups, plates), you can  
switch to “half load”. This will save  
water, energy and time. It is 
recommended to put a little less  
detergent in the detergent dispenser  
than for a full load. 
·  Hygiene *
Hyg
ie ne
The temperature is increased during the  
cleaning process. This increases the  
hygiene status. This additional option is  
ideal for cleaning e.g. chopping boards  
and baby bottles. 
Ï  Intensive zone *
In
te nsiv
e z one
Perfect for a mixed load. You can wash  
very soiled pots and pans in the lower  
basket together with normally soiled  
utensils in the upper basket. The spray  
pressure in the lower basket is  
intensified, the rinsing temperature is  
increased slightly.  
¿  Extra drying *
E
xt r
a d r
yin g
An increased temperature during the  
final rinse and an extended drying 
phase ensure that even plastic parts dry  
better. There is a slight increase in the  
energy consumption.
 
						

							enOperating the appliance
20
1 Operating 
the appliance
Operating theappliance
Programme data 
The programme data (consumption  
values) can be found in the summary of  
instructions. They refer to normal  
conditions and the water hardness set  
value  •:‹… . Different influencing factors 
such as e.g. water temperature or line  
pressure may result in deviations.
Aq u
a s ens
orAqua sensor *
* depending on model 
The Aqua sensor is an optical  
measuring device (light barrier) which 
measures the turbidity of the rinsing  
water. 
The Aqua sensor is used according to  
the programme. If the Aqua sensor is  
active, “clean” rinsing water can be  
transferred to the next rinse bath and  
water consumption can be reduced by  
3–6 litres. If the turbidity is greater, the  
water is drained and is replaced with  
fresh water. In the automatic  
programmes the temperature and  
running time can also be adjusted to the  
degree of soiling. 
Switching on the appliance 
1. Turn on the tap fully.
2. Switch on ON/OFF switch (. 
The Eco 50° programme display  
flashes. This programme remains  
selected if no other programme  
button 0 is pressed. The expected 
programme duration  
flashes on the digital display )*.
3. Press the START button h. 
The programme starts running. Note 
- for environmentally friendly operation  
of the dishwasher:
For ecological reasons the Eco 50°  
programme is preset whenever the  
appliance starts. This conserves 
environmental resources and not least  
saves you money. 
The Eco 50° programme is a 
particularly environmentally friendly  
programme. According to EU  
regulation 1016/2010 it is the 
“Standard programme” which is the  
most efficient standard cleaning cycle  
for cleaning normally soiled utensils in  
terms of the combined energy and  
water consumption for cleaning these  
types of utensils.
Pr
o
gr amme  seq
ue nce
 in dica
to rProgramme sequence 
indicator  )
Remaining running time  
display 
When the programme is selected, the  
remaining running time of the  
programme is indicated on the digital  
display  )*. 
The running time is determined during 
the programme by the water  
temperature, the number of utensils as  
well as the degree of soiling and may  
vary (depending on the selected  
programme). -
/, Your dishes are being 
cleaned.
5 /% Your dishes are being rinsed.
= /< Your dishes are being dried.