Siemens Sr 25e830 Operating Instructions

							Fault, what to do?en
31
Rust spots on the cutlery. Cutlery not adequately rust-
resistant. Knife blades are  
frequently more severely  
affected. Use corrosion-resistant cutlery.
Cutlery will also rust if rusting 
parts are rinsed at the same time 
(pan handles, damaged utensil  
baskets, etc.). Do not wash rusting parts.
Salt content in the rinsing water 
too high, as salt dispenser lock  
not fastened firmly or salt was 
spilled while being refilled. Fasten salt dispenser lock firmly or remove  
spilled salt.
The appliance does not  
start. The mains fuse has tripped. Check mains fuse. 
Power cord not inserted. Ensure that the power cord 
is plugged all 
the way into the back of the appliance and  
into the socket. Check that the socket  
functions.
The appliance door has not been 
shut properly. Close the door.
Programme starts 
automatically. You did not wait until programme 
ended. Perform reset.  
(See Terminating the programme).
Appliance cannot be set  
(hardness, final rinse, ...). Appliance is in the programme. 
Appliance can be set at the start  
of the programme only. Perform reset (see Terminating  
the programme) and set the appliance  
according to the instructions for use.
The door is difficult 
to open. Child-proof lock is activated. Deactivate childproof lock
. (See instructions 
for use at the back)
Door cannot be closed. Door lock has been activated. Cl ose door with increased force.
Door cannot be closed due to 
installation. Check appliance installation: Door or 
attached parts must close without  
obstruction.
Cover on the detergent 
dispenser cannot be  
closed. Detergent dispenser or cover  
guide blocked by sticky detergent  
residue. Remove detergent residue.
Detergent residue 
in the detergent dispenser  
or in the tablet collecting  
tray. Spray arms blocked by utensils,  
therefore detergent is not rinsed  
out.
Ensure that the spray arms can rotate freely.
The detergent dispenser was  
damp when filled. Pour detergent into the dry detergent 
dispenser only.
Fault Cause Remedial action
 
						

							enCustomer service
32
 
4
Customer serviceCustomer service
If you are unable to rectify the fault,  
please contact your customer service.  
We always find a suitable solution, even  
to avoid unnecessary visits 
by technicians. Contact information  
for your nearest customer service can  
be found on the back of these 
instructions for use or on the enclosed  
customer service list. When calling,  
please state the appliance number (E-
Nr. = 1) and the production number  
(FD = 2) which can be found on the  
rating plate 92 on the appliance door. Rely on the competence of the manufa 
cturer.
 Contact us. You can therefore be 
sure that the repair is carried out  
by trained service technicians who carry  
original spare parts for your domestic  
appliances. 
Appliance stops 
in the programme or  
programme is interrupted.
Door not closed properly. Close the door. 
Do not place utensils or fragrance  
dispenser in the tablet collecting 
tray. 
Top basket presses against inner  
door and prevents door from  
being closed securely. Check whether rear panel is being pressed  
in, e.g. by socket or by hose holder which 
has not been removed.
Power and/or water supply 
interrupted. Restore power and/or water supply.
Filling valves making 
striking noises. Depends on domestic installation, 
as appliance is not defective. No  
effect on appliance function. No remedial action possible.
Knocking or rattling noise. Spray arm strikes the utensil s, 
utensils not positioned correctly. Position utensils so that the spray arms do  
not strike the utensils.
If there is a low load, the water 
jets strike the washing tank  
directly. Load the appliance with more utensils or  
distribute the utensils more evenly  
in the dishwasher.
Light utensils move during  
the wash cycle. Arrange light utensils securely.
Unusual foam formation. Handwash liquid in the rinse ai d 
dispenser. Immediately refill rinse aid dispenser with  
rinse aid.
Rinse aid spilled. Remove rinse aid with a cloth.
Fault Cause Remedial action

 

 
						

							Installation and connectionen
33
5 Installation and 
connection
Installation and connection
The dishwasher must be connected  
correctly, otherwise it will not function 
properly. The specifications for the inlet  
and outlet as well as the electrical  
connected loads must correspond with 
the required criteria as  
specified in the following paragraphs  
or in the installation instructions. 
Install the appliance in the correct  
sequence: 
1. Checking appliance on delivery
2. Installing the appliance
3. Waste water connection
4. Fresh water connection
5. Electrical connection
Product package 
If you have any complaints, contact  
the dealer where you purchased  
the appliance or our customer service.

						

							enInstallation and connection
34
Installation 
The required installation dimensions can  
be found in the installation instructions.  
Level the appliance with the aid of the  
height-adjustable feet. Ensure that the 
appliance is situated securely on the  
floor.

						

							Installation and connectionen
35
Warm water connection
W
ar m w
at e
r c onn
ec t
io n
* depending on model 
The dishwasher can be connected  
to cold or hot water up to max. 60 °C.  
Connection to hot water  
is recommended if the hot water can be  
supplied by energetically favourable  
means and from a suitable installation, 
e. g. solar heating system with  
circulation line. 
This will save energy and time. 
The hot water setting ‘:‹‚  allows you 
to adjust your appliance optimally  
to operation with hot water. 
It is recommended to have a water  
temperature (temperature of the  
incoming water) of at least 40 °C  
and no more than 60 °C. 
It is not recommended to connect  
the appliance to hot water if the water 
is supplied from an electric boiler. 
Setting hot water: 
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press and hold down the START  
button @.
4. Rotate programme selector 8 
until ‘:‹‚  is indicated on the digital 
display H.
5. Release button.  
The factory-set value  ‘:‹‹  is lit on 
the digital display  H.
To change the setting: 
1. By rotating the programme  
selector 8, you can switch the hot 
water setting off ‘:‹‹  or on ‘:‹‚ .
2. Press START button @.
The set value is saved.  Electrical connection
						

							enInstallation and connection
36
Removing the appliance 
Also observe  
the sequence of worksteps here. 
1.
Disconnect the appliance from  
the power supply.
2. Turn off the water supply.
3. Disconnect the waste water  
and fresh water connections.
4. Loosen fastening screws for the  
furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully 
pulling the hose behind.
Transportation 
Empty the dishwasher and secure loose  
parts. 
Drain the appliance according to the  
following steps: 
1. Turn on the tap.
2. Close the door.
3. Switch on ON/OFF switch  (.
4. Select programme with the highest  
temperature. 
The expected programme duration is  
indicated on the numerical display  
H . 
5. Press START button  @.
Programme sequence starts. 6.
After approx. 4 minutes press the  
START button @ until  ‹:‹‚  is 
indicated on the digital display.   
After approx. 1 min is indicated on  
the digital display  ‹:‹‹ .
7. Switch off ON/OFF switch  (.
8. Turn off the tap, disconnect supply  
hose and drain water.
Transport appliance upright only. 
(This prevents residual water from  
running into the machine control and  
damaging the programme sequence.)
Protection against frost
Pr ote
ct io
n a gain s t
 fr o
st  (
Em pty
in g
 t h
e a pplia n ce)
If the appliance is in a room where there  
is a risk of frost (e.g. holiday home),  
empty the appliance completely (see 
Transportation).

 
						

							
      



   



DownloadedfromDishWasherManualcomManuals 
						

							 
 

 
 


 

 
 
 
 
 



 
 
 






 
 
 


 

 


*9000868097* 
9000868097
 en (9301) 440EG