Siemens Sn 66t096 Operating Instructions

Operating the applianceen
21
4.
Release both buttons. 
The LED for button # flashes 
and the digital display 8 displays 
the factory setting •:‹… .
5. Press programme button # until 
the factory set value  ‚:‹‚  
is indicated on the digital  
display 8.
To change the setting: 
1. By pressing the button  3, you can 
switch the function off ‚:‹‹  
or on ‚:‹‚ .
2. Press START button ).
The set value is saved. 
3. Close the door.
Remaining running time  
display 
When the programme is selected, the...

enOperating the appliance
22
Automatic switch off after end  
of programme or interior light*
Au
t
om at ic  switc
h o ff / i n t
er ior  lig h t
* depending on model 
To save energy, the dishwasher can be  
automatically switched off 1 min or 120 
min after the programme ends. 
The setting can be selected from  ˜:‹‹  
to  ˜:‹ƒ .
1. Open the door.
2. Switch on ON/OFF switch (.
3. Hold down programme button # 
and press START button ) 
until •:‹ ... is indicated on the digital 
display.
4. Release both...

Cleaning and maintenanceen
23
3.
To continue the programme, switch  
on the ON/OFF switch  ( again.
4. Close the door.
T
er min
at in
g t he pr o
gr ammeTerminating the programme 
(Reset) 
1. Open the door.
2. Press START button  ) for 
approx. 3 sec. 
The numerical display  8 indicates 
‹ :‹‚ .
3. Close the door. 
The programme sequence lasts  
approx. 1 min. On the digital display  
8  is indicated  ‹:‹‹ .
4. Open the door.
5. Switch off ON/OFF switch  (.
6. Close the door.
Changing the programme 
When...

enCleaning and maintenance
24


Fault, what to do?en
25
Spray arms 
Limescale and contaminants in the  
rinsing water may block nozzles and  
bearings on the spray arms 
1: and 
1J .
1. Check outlet nozzles on the spray  
arms for blockages.
2. Unscrew the upper spray arm  1:.
3. Remove the lower spray arm  1J 
upwards.
4. Clean spray arms under running 
water.
5. Re-engage or screw on spray arms.
3 Fault, what to do?Fault, what to do?
Experience has shown that you can  
rectify most faults which occur in daily  
operation yourself....

enFault, what to do?
26
Waste water pump 
Large food remnants or foreign objects  
which were not captured by the filters  
may block the waste water pump. The  
rinsing water will then be above the filter.  
In this case:
1.
First always disconnect the  
appliance from the power supply.
2. Take out top basket  12 and bottom 
basket  1b.
3. Remove the filters  1Z.
4. Scoop out water, use a sponge if  
required.
5. Prise out the white pump cover  
(as illustrated) using a spoon. Grip  
the cover on the...

Fault, what to do?en
27
Fault table 
Fault Cause Remedial action 
“Check water supply”  
display
@ lights up. Supply hose kinked. Install supply hose without kink
s.
Tap turned off. Turn on the tap. 
Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min.  
when water supply is open.
Filter in the water supply blocked. Switch off the applia nce and pull out 
the mains plug. Turn off the tap. Unscrew  
water connection.  
Clean filter in the supply hose. Screw water  
connection on...

enFault, what to do?
28
A different error code is  
indicated on the digital  
display. 
(
“ :‹‚  to“:„‹ ) A technical fault has probably  
occurred.
Switch off appliances with the ON/OFF 
switch
(. After a short time restart 
the appliance. 
If the problem recurs, turn off the tap and  
pull out the mains plug.  
Call customer service and mention the error  
code.
Display flashes Door not closed properly. Close the door . Ensure that no objects 
(utensil, fragrance dispenser) are protruding 
over the...

Fault, what to do?en
29
Utensils not dry. No or too little rinse aid 
in the dispenser. Refill rinse aid.
Programme selected without  
drying. Select programme with drying (see 
Overview of programmes, Programme  
sequence).
Water collecting in depressions 
on the utensils and cutlery. Arrange utensils in a sloping position, 
arrange affected utensils as sloping  
as possible.
The combined detergent used 
has a poor drying performance. Use different combination detergent with 
better drying performance....

enFault, what to do?
30
Food remnants  
on the utensils.
Utensils placed too closely 
together, utensils basket  
overfilled. Arrange utensils with adequate clearance  
between them ensuring that the spray jets  
can reach the surface of the utensils.  
Prevent contact points.
Spray arm rotation obstructed. Arrange utensils so t hat the spray arm can 
rotate without obstruction.
Spray arm nozzles blocked. Clean the spray arm nozzles , 
(See Cleaning and maintenance).
Filters  1Z dirty. Clean filters,...