Siemens Sn 66m054 Operating Instructions

							en
11
Pans
Bottom basket 1b
Tip 
Heavily soiled utensils (pans) should  
be placed in the bottom basket. The more 
powerful spray jet provides a better  
dishwashing result. 
Tip 
Other examples, such as the best way  
of loading your dishwasher, can be found 
on our homepage as a free download. The 
corresponding Internet address can  
be found on the back page of these  
instructions for use.
Cutlery basket
You should always place cutlery unsorted  
with the points downwards.   
To prevent injuries, place long, pointed  
implements and knives on the knife shelf.
E
ta
gereEtagere *
The etagere and the space underneath  
can be used for small cups and glasses 
or for larger items of cutlery, such as 
wooden spoons or serving cutlery. The  
etagere can be folded up if not required.  
* Depending on the model, a 3-fold height  
adjustment is possible. To do this, first 
place the etagere vertically and pull up, 
then place at a slight angle, push down 
to the required height (1, 2, or 3) and snap 
into place.
Fo
ldin
g
 s
p
ik
esFolding spikes *
* depending on model 
The spikes can be folded down to improve  
arrangement of pans, bowls and glasses.






        
						

							en
12
Small accessories holder *Sma
ll a
ccessor
ie
s
 h
o
ld
er
* depending on model 
Light-weight plastic accessories, e.g. cups,  
lids, etc. can be held securely in the small  
accessories holder.
Knife shelf *Kn
ife
 she
lf
* depending on model 
Long knives and other utensils can be  
arranged horizontally.
Ad
ju
s
tin
g
 th
e
 h
e
ig
h
t o
f
 th
e
 b
asketAdjusting the height of the 
basket *
* depending on model 
If required, the height of the upper utensils  
basket  1 can be adjusted to provide 
more space for tall utensils either in the  
upper or lower basket. 
Appliance height 81.5 cm 
Appliance height 86.5 cm 
Select one of the two following procedures  
according to the design of the top basket  
for your appliance model:
Top basket Bottom 
basket
Setting 1 max. ø 22 cm 30 cm 
Setting 2 max. ø 24.5 cm 27.5 cm 
Setting 3 max. ø 27 cm 25 cm
Top basket Bottom basket
Setting 1 max. ø 24 cm 33 cm 
Setting 2 max. ø 26.5 cm 30.5 cm 
Setting 3 max. ø 29 cm 28 cm
  
						

							en
13
Top basket with side levers
– Pull out the top basket 1 out. 
–To  lower the basket, press in the left 
and then the right lever on the outside  
of the basket. In doing so, hold the  
sides of the basket along the upper 
edge to prevent it from suddenly 
dropping.
–To  raise the basket, hold the basket on 
the sides of the upper edge and lift it  
up.
– Before re-inserting the basket again,  ensure that it is at the  same height on 
both sides. Otherwise, the appliance  
door cannot be closed and the upper  
spray arm will not be connected to the  
water circuit. 
Top basket with  upper and lower 
roller pairs
– Pull out the top basket  1 out. 
– Remove the upper basket and re- attach it to the upper (stage 3) or lower 
(stage 1) rollers. You can use tablets as well as powder 
or liquid detergents for dishwashers, but 
never use washing up liquid. The dosage  
can be individually adjusted with powder  
or a liquid detergent according 
to the degree of soiling. Tablets contain 
an adequately large amount of active  
ingredients for all cleaning tasks. Modern,  
powerful detergents predominantly 
use a low-alkaline formulation with  
phosphate and enzymes. Phosphates  
bond the lime in the water. Enzymes break 
down starch and remove protein. 
Phosphate-free detergents are less  
frequent. These have a slightly weaker  
lime bonding capacity and require 
a higher dosage. To remove coloured  
stains (e.g. tea, tomato sauce), oxygen- 
based bleaching agents are usually used. 
Note 
To ensure a good washing result, always  
follow the instructions on the detergent  
packaging! 
If you have further questions,  
we recommend that you contact  
the detergent manufacturers’ helpline.
ã=Warning
Read and observe the safety information  
and instructions for use on the packaging  
for cleaning and rinsing agents.
Detergent
   
						

							en
14
Adding detergent
– If the detergent dispenser 9 is still 
closed, press the lock  9* to open the 
detergent dispenser. 
Pour detergent into the dry detergent  
dispenser 9 only (insert tablet flat, 
not on its edge). 
Dosage: see manufacturer’s  
instructions on the packaging.  
The graduated detergent  
dispenser 9 helps you add the 
correct amount of powder or liquid  
detergent. 
Usually 20 ml–25 ml are adequate  
for normal soiling. If using tablets, one  
tablet is adequate.
– Close the cover on the detergent  dispenser by sliding it up until the lock  
engages without difficulty. 
The detergent dispenser opens  
automatically at the optimum time 
depending on the programme.  
The powder or liquid detergent  
is distributed in the appliance and is 
dissolved, the tablet falls into the tablet 
collecting tray where it dissolves  
in doses. Tip 
If the utensils are only lightly soiled, slightly  
less than the indicated amount 
of detergent is usually adequate.  
Suitable detergents and care products  
can be purchased online via our website 
or via customer service (see back page). 
Combination detergent
Apart from conventional detergents (Solo), 
a number of products are offered with 
additional functions. These products 
contain not only the detergent but also  
rinse-aid and salt replacement substances  
(3in1) and, depending on the combination 
(4in1, 5in1, etc.), additional components 
such as glass protection or stainless steel 
cleaner. Combination detergents function 
only up to a specific degree of hardness  
(usually 26° Clarke). Over this limit salt  
and rinse-aid must be added.  
As soon as combined detergents  
are used, the rinse programme is adjusted  
automatically to ensure the best possible  
rinsing and drying result.
ã=Warnings
–Do  not place small parts for washing in 
the tablet collecting tray  12; this 
prevents the tablet from dissolving  
evenly.
– If you want to add more utensils after  the programme has started, do  not 
use the tablet collecting tray 12 
as a handle for the upper basket. 
The tablet could already be there and 
you will touch the partially dissolved 
tablet.



 
						

							en
15
Notes 
– You will obtain optimum rinsing 
and drying results by using solo  
detergents and applying salt and rinse 
aid separately.
– If programmes are short, tablets  may not have full cleaning effect due to  
different dissolving properties 
and there may even be undissolved 
detergent residue. It is recommended  
to use washing powder for these  
programmes.
– The Intensive programme (on some  models) requires one tab only. When  
using washing powder, you can apply  
some of this cleaning agent to the 
inside of the appliance’s door.
– Even if the rinse-aid and/or salt refill  indicator is lit, the rinse programme will 
run correctly with combined 
detergents.
– If using detergents in a water-soluble  protective cover: Take hold of the 
cover with dry hands only and put 
the detergent into an absolutely 
dry detergent dispenser only, otherwise 
the detergent may stick.
– If you switch from combined  detergents to solo detergents, ensure 
that the water softening system and 
amount of rinse aid have been set to 
the correct value.
 
						

							en
16
The max. possible number of programmes is illustrated 
in this overview. 
The corresponding programmes for your appliance can be  found on the fascia.
Programme selection
You can select a suitable programme  
according to the type of utensils and 
degree of soiling.
Information for test institutes
Test institutes can request the conditions 
for running comparison tests by sending 
an e-mail to  
[email protected].  
Quote the appliance number (E­Nr.) 
and the production date (FD) which you  
can find on the rating 
plate 92on the appliance door.
Overview of programmes
Type of utensils Type of soiling Programme Possible additional 
optionsProgramme sequence
pots and pans,  non-sensitive  utensils 
and cutlery very adhesive 
burned-in or dried-on  food remnants 
containing starch 
or protein
±  / °
Intensive 70°
allPrerinse
Clean 70°
Intermediate rinse
Final rinse 65° Dry
Á
Auto 45° – 65° Is optimised according to 
the soiling with the aid  of sensors.
mixed utensils  and cutlery part dried, common 
household food 
remnants
á  / à
Eco 50° Prerinse
Clean 50°
Intermediate rinse
Final rinse 65° Dry
sensitive utensils,  cutlery, 
temperature-
sensitive plastic 
and glasses slightly adhesive, 
fresh food remnants
é  / è
Gentle 40° Intensive zone
Express Wash/  Speed Perfect  (VarioSpeed)
Half load
Extra drying Prerinse
Clean 40°
Intermediate rinse Final rinse 55° Dry
ñ / ð
Quick 45° Extra drying Clean 45°
Intermediate rinse Final rinse 55°
all types of utensils cold rinsing, 
intermediate  cleaning
ù  / ø
Prerinse none Prerinse
 
						

							en
17
* depending on model 
Additional options can be set with the  
buttons 
X.
Express
 W
ash
/ S
peed
 P
e
rf
ec
t (
Var
io
Speed)Ÿ  Express Wash/ Speed Perfect/
(VarioSpeed) *
This function can reduce the running time  
by approx. 20% to 50% depending on the  
selected rinse programme. The change in  
the running time is indicated on the digital 
display h. To obtain optimum cleaning 
results at a reduced running time, water  
and energy consumption are increased.
Ha
lf lo
ad§  Half load *
If you have only a few items to wash (e.g.  
glasses, cups, plates), you can switch to 
“half load”. This will save water, energy  
and time. It is recommended to put a little  
less detergent in the detergent dispenser 
than for a full load.
· Hygiene *Hyg
ie
ne
The temperature is increased during the  
cleaning process. This increases the 
hygiene status. This additional option is  
ideal for cleaning e.g. chopping boards  
and baby bottles.
Ï  Intensive zone *Inte
ns
iv
e
 z
on e
Perfect for a mixed load. You can wash  
very soiled pots and pans in the lower  
basket together with normally soiled  
utensils in the upper basket. The spray 
pressure in the lower basket is intensified, 
the rinsing temperature is increased 
slightly. 
¿  Extra drying *Ex
tr
a
 d
ry
in
g
An increased temperature during the final  
rinse and an extended drying phase  
ensure that even plastic parts dry better.  
There is a slight increase in the energy 
consumption.
Programme data
The programme data (consumption 
values) can be found in the summary of 
instructions. They refer to normal 
conditions and the water hardness set  
value  •:‹… . Different influencing factors 
such as e.g. water temperature or line  
pressure may result in deviations.
Aqua
 s ensorAqua sensor *
* depending on model 
The Aqua sensor is an optical measuring  
device (light barrier) which measures the  
turbidity of the rinsing water. 
The Aqua sensor is used according to the  
programme. If the Aqua sensor is active,  
“clean” rinsing water can be transferred to  
the next rinse bath and water consumption 
can be reduced by 3–6 litres. If the  
turbidity is greater, the water is drained  
and is replaced with fresh water. In the 
automatic programmes the temperature 
and running time can also be adjusted to  
the degree of soiling.
Switching on the appliance
– Turn on the tap fully. 
– Open the door. 
–Switch on ON/OFF  switch( . 
The display of the last selected  
programme flashes. This programme  
remains selected if no other  
programme button 0 is pressed. The 
expected programme duration flashes  
on the digital display h.
– Press the START button `. 
– Close the door. The programme starts running.
Additional optionsWashing the dishes
 
						

							en
18
Op
tic
a
l d
is
p
la
y wh
il
e
 th
e
 p
rogramme
 is
 r
unn
in
gOptical display while the 
programme is running *
* depending on model 
While the programme is running, a light  
spot shines on the floor under the 
appliance door. Do not open the  
dishwasher door until the light point is no  
longer visible on the floor. 
If the appliance is installed at eye-level,  
with flush furniture front, the light point is  
not visible.  
This function can be changed as follows: 
– Open the door. 
–Switch on ON/OF F switch ( .
– Hold down programme button  # and 
press START button  ` until  •:‹ .... is 
indicated on the digital display.
–Rel ease both buttons.
The LED for button  # flashes and the 
digital display  h displays the factory 
setting  •:‹… .
– Press programme button # until the 
factory set value  ‚:‹‚  is indicated on 
the digital display h.  
To change the setting: 
– By pressing the button  3, you can 
switch the function off  ‚:‹‹  or on 
‚ :‹‚ .
– Press START button `.
The set value is saved. 
– Close the door.
Remaining running time display
When the programme is selected, the  
remaining running time of the programme  
is indicated on the digital display  h. 
The running time is determined during the  
programme by the water temperature, the  
number of utensils as well as the degree  
of soiling and may vary (depending on the 
selected programme).
T
im
er
 p
rogramm in
gTimer programming *
* depending on model 
You can delay the start of the programme  
in 1-hour steps up to 24 hours. 
– Open the door. 
–Switch on ON/OFF  switch ( .
– Press button  P + until the digital 
display  h jumps to  œ:‹‚ .  
– Press  P + or – button until the 
displayed time corresponds with your  
requirements.
– Press START button  `, timer 
programming is activated.
– To delete timer programming, press  the  P  + or – button until  h œ :‹‹  is 
indicated on the digital display.   
You can change your programme  
selection at any time until the  
programme starts.
– Close the door.
End of programme
The programme has ended when the  
value  ‹:‹‹  is indicated on the numerical 
display  h.  
The end of the programme is also 
indicated by an acoustic signal. This 
function can be changed as follows: 
– Open the door. 
–Switch on ON/OFF  switch ( .
– Hold down programme button  # and 
press START button  ` until  •:‹ .... is 
indicated on the digital display.
– Release both buttons.
The LED for button  # flashes and the 
digital display  h displays the factory 
setting  •:‹… .
– Press programme button  # until the 
factory set value  ›:‹ƒ  is indicated on 
the digital display  h.  
To change the setting, 
– Press programme button  3. Each 
time the button is pressed, the set  
value increases by one level; when the 
value of ›:‹„  has been reached, the 
display jumps back to ›:‹‹  (off).
– Press START button  `, the set value 
is saved.
– Close the door.
 
						

							en
19
Sw
itc
h
in
g
 off a
ut
omat
ic
al
ly
 afte
r
 t
he
 e
nd
 of th
e
 p
rogrammeSwitching off automatically after 
the end of the programme *
* depending on model 
To save energy, the dishwasher is  
switched off 1 minute after the programme 
ends (factory setting). 
Automatic disconnection can be adjusted  
from ˜:‹‹  to ˜:‹ƒ .
– Open the door. 
–Switch on ON/OF F switch( .
– Hold down programme button # and 
press START button ` until •:‹ ... is 
indicated on the digital display.
–Rel ease both buttons.
The LED for button # flashes and the 
digital display h displays the factory 
setting •:‹… .
– Press programme button # until the 
factory set value ˜:‹‚  is indicated on 
the digital display h.  
To change the setting: 
– Press programme button 3.
Each time the button is pressed, the  
set value increases by one level; when  
the value of ˜:‹ƒ  has been reached, 
the display jumps back to ˜:‹‹  (off).
– Press START button `. 
The set value is saved. 
– Close the door.
Switching off the appliance
Short time after the end of the programme: 
– Open the door. 
– Switch off ON/OFF switch  (.
– Turn off the tap (not applicable if Aqua- Stop fitted).
– Remove the utensils when they have  cooled down.
ã=Warning
At the end of the programme please open  
the door fully and not partially when  
emptying the dishwasher. Any escaping  
water vapour could damage sensitive 
worktops.
Interrupting the programme
– Open the door. 
– Switch off ON/OFF switch  (.
The LEDs go out. The programme is  
saved.  
If the door was opened on an  
appliance which has a warm water 
connection or is heated, first leave the  
door ajar for several minutes and then  
close. Otherwise, expansion (pressure) 
may cause the appliance door to 
spring open or water to run out of the 
appliance.
– To continue the programme, switch on  the ON/OFF switch  ( again.
– Close the door.
Term
in
a
tin
g
 th
e
 p
rogrammeTerminating the programme  
(Reset)
– Open the door. 
– Press START button  ` for 
approx. 3 sec.
The numerical display  h indicates 
‹ :‹‚ .
– Close the door. The programme sequence lasts  
approx. 1 min. On the digital display  
h  is indicated  ‹:‹‹ .
– Open the door. 
– Switch off ON/OFF switch  (.
– Close the door.
Changing the programme
When the START button  ` has been 
pressed, the programme cannot be  
changed. 
The only way a programme can be  
changed is by Cancel programme (Reset).
˜
:‹‹ Appliance does not switch off  
automatically
˜ :‹‚ Off after 1 min
˜ :‹ƒ Off after 120 min
 
						

							en
20
Intensive drying
The final rinse uses a higher temperature  
which improves the drying result. The 
running time may increase slightly. 
(Caution if utensils are delicate!) 
– Open the door. 
–Switch on ON/OFF switch ( .
– Hold down programme button  # and 
press START button  ` until  •:‹ .... is 
indicated on the digital display. 
–Rel ease both buttons.
The LED for button  # flashes and the 
digital display  h displays the factory 
setting  •:‹… .
– Press programme button  # until the 
factory set value  š:‹‹  is indicated on 
the digital display  h.  
To change the setting,
– Press the button  3 to switch the 
Intensive drying on  š:‹‚  or off  š:‹‹ .
– Press START button  `.
The set value is saved. 
– Close the door. A regular inspection and maintenance of  
your machine will help to prevent faults. 
This saves time and prevents problems.
Overall condition of the machine
– Check spray arm for grease and 
limescale deposits.
If you find such deposits: 
– Fill detergent dispenser with detergent.  Start the appliance without utensils in  
the programme with the highest rinsing  
temperature.
Clean the appliance with detergents/ 
appliance cleaners which are particularly  
suitable for use with dishwashers. 
– Regularly clean door seal with a damp  cloth.
Never use a steam cleaner to clean your  
dishwasher. The manufacturer is not liable 
for any consequential damage. 
Regularly wipe the front of the appliance  
and fascia with a damp cloth; water and a 
little washing up liquid are adequate. Do 
not use sponges with a rough surface or 
abrasive detergents, as these could  
scratch the surfaces. 
Stainless steel appliances: To prevent  
corrosion, avoid using sponge cloths or  
wash them out thoroughly several times  
before using for the first time.
ã=Warning
Never use other chlorinated household  
detergents! Health hazard!
Special salt and rinse aid
– Check the refill indicators  @ and 
H . If required, refill salt and/or rinse 
aid.
Maintenance and care