Siemens Sn 66m051 Instructions For Use

							en11
Adjusting
 the height of the
basket *
* depending  on model
If required, the height of the upper utensils basket can be adjusted to provide more space for tall utensils either in the upper or lower basket. Appliance height 81.5 cm
Top
basketBottom basket
Setting 1 max.  j22 cm30 cm
Setting 2 max. j24.5 cm27.5 cm
Setting 3 max. j27 cm25 cm
Appliance height 86.5 cm
Top
basketBottom basket
Setting 1 max.  j24 cm33 cm
Setting 2 max. j26.5 cm30.5 cm
Setting 3 max. j29 cm28 cm
Select one of the two following procedures according to the design of the top basket for your appliance model: Top
 basket with side levers
(Rackmatic)
Pull  out the top basket 20.
To  lower  the basket, press in the left
and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upperedge to prevent it from suddenly dropping.
To  raise  the basket, hold the basket on
the sides of the upper edge and lift it up.
Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upperspray arm will not be connected to the water circuit.
Top  basket with upper
and lower roller pairs
Pull  out the top basket.
Remove the upper basket and re-attach it to the upper (stage 3) or lower (stage 1) rollers.
   
						

							en
12 Detergent
Y ou can use tablets as well as powder
or liquid detergents for dishwashers, but never use washing up liquid. T ablets
contain not only detergent but alsorinse-aid and salt (3in1) and, depending on the combination (4in1, 5in1, etc.), additional components such as glassprotection or stainless steel cleaner .
If tablets contain rinse-aid and salt, it isusually not necessary to add additional rinse-aid and salt up to a specific degree of hardness. If the degree of hardness is higher and if using solo detergents (powder or liquid detergents or tabletswithout rinse-aid and salt) rinse-aid and salt must be added. The appliance doses these automatically according to the preset values for water hardness and amount of rinse-aid. As soon as combined detergent products are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result. 
TipFollow the instructions for use or the instructions on the detergent packaging to ensure that rinse-aid and salt are used 
effectively. If you have further questions, we recom- mend that you contact the detergent manufacturers helpline. Detergent
 dispenser
with dosing aid The  graduated detergent dispenser 
30
helps you add the correct amount of powder or liquid detergent: lower line: 15 ml
middle line: 25 ml
full: 50 ml
Adding  detergent
Pour detergent into the dispenser 30
(insert tablet flat, not on its edge).  Dosage: see manufacturer s
instructions on the packaging.
Close the cover on the detergent dispenser by sliding it up until the lock engages without dif ficulty.
The detergent dispenser opens automatically at the optimum time depending on the programme.The powder or liquid detergent is distributed in the appliance and is dissolved, the tablet falls into thetablet collecting tray where it dissolves in doses.
Tip If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
  
						

							en13
Warnings
Do  not  place small parts for washing
in the tablet collecting tray 
22 ; this
prevents the tablet from dissolving 
evenly.
If you want to add more utensils after the programme has started, do  not
use the tablet collecting tray 
22
as a handle for the upper basket. The tablet could already be there and you will touch the partially dissolvedtablet.
Note
Y ou will obtain optimum rinsing and
drying results by using solo detergents and applying salt and rinse-aid 
separately.  
f programmes are short, tablets may not have full cleaning ef fect due to different
dissolving properties and there may even be undissolved detergent residue. It is recommended to use washingpowder for these programmes.
The Intensive programme (on some models) requires one tab only . When
using washing powder , you can apply
some of this cleaning agent to theinside of the appliance s door.
Even if the rinse-aid and/or salt refill indicator is lit, the rinse programme will run correctly if combined detergents are used (when using combineddetergents, add rinse-aid at a water hardness above 21  dH ± see chapter
entitled ªRinse-aidº).
If you switch from combined detergents to solo detergents, ensure that thewater softening system and amount of rinse-aid have been set to the correct value.
 
						

							en
14 Overview
 of programmes
The  max. possible number of programmes is illustrated in this overview . The corresponding
programmes for your appliance can be found on the fascia.
Programme
T ype of utensils
and soilingProgramme sequencePossible additional options
Intensive 70 Pots, utensils and cutlery Highly soiledPrerinse Clean 70
Intermediate rinse Final rinse 70 
Dryall
Normal 65 Utensils and cutlery Normally soiledPrerinse Clean 65
Intermediate rinse Final rinse 65 
Dryall
Auto 45 ±65 Utensils and cutlery Normally soiledIs optimised according to the soiling with the aid of sensors.all
Eco 50 Utensils and cutlery Normally soiledPrerinse Clean 50 
Intermediate rinse Final rinse 65 
Dryall
Gentle 40 Utensils and cutlery Lightly soiledPrerinse Clean 40
Intermediate rinse Final rinse 55 
Dry Reduce T ime
Half load Extra drying
Quick 45 Utensils and cutlery Lightly soiledClean 45 
Intermediate rinse Final rinse 55 Extra drying
PrerinseLightly soiledPrerinsenone
Programme  selection
You  can select a suitable programme
according to the type of utensils and degree of soiling. Information  about comparability
tests The  conditions for running comparability
tests can be found on the supplementary sheet ªInformation for comparability testsº.
              
						

							en15
Additional
 options
* depending  on model
Additional options 
7 can be set with the
buttons.
Saving  time (V arioSpeed) *
The  >>Save time
						

							en
16
Optical
 display while the
programme is running *
* depending  on model
While the programme is running, a light spot shines on the floor under the appliance door . Do not open the
dishwasher door until the light pointis no longer visible on the floor .
If the appliance is installed at eye-level,with flush furniture front, the light pointis not visible. This function can be changed as follows:
Open the door .
Switch on ON/OFF switch 1.
Hold down programme button A
and press ST ART button 
8 until
on the digital display 
 is indicated.
Release both buttons.
Press programme button A  until
the factory set value 
 is indicated
on the digital display 
9.
T o change the setting:
By pressing the C  button, you can
switch the function of f 
 or on .
Press START button 8.
The set value is saved.
Close the door .
Remaining  running time display
When  the programme is selected, the
remaining running time of the programme is indicated on the digital display 
9.
The running time is determined during the programme by the water temperature, the number of utensils as well as the degreeof soiling and may vary (depending on the selected programme). Timer
 programming *
* depending  on model
Y ou can delay the start of the programme
in 1-hour steps up to 24 hours.
Open the door .
Switch on ON/OFF switch 1.
Press 6 + button until the digital
display 
9 jumps to .
Press 6 + or ± button until the
displayed time corresponds with your requirements.
Press ST ART button 8, timer
programming is activated.
T o delete timer programming, press
the 
6 + or ± button until 
is indicated on the digital display .
Y ou can change your programme
selection at any time until the programme starts.
Close the door .
End  of programme
The  programme has ended when the
value 
 is indicated on the numerical
display 
9.
The end of the programme is also indicated by an acoustic signal.This function can be changed as follows:
Open the door .
Switch on ON/OFF switch 1.
Hold down programme button A
and press ST ART button 
8 until on
the digital display 
 is indicated.
Release both buttons. The LED for button 
A  flashes and the
digital display displays the factory setting 
.
Press programme button A  until the
factory set value 
 is indicated on
the digital display .
           
						

							en17
T
o change the setting,
press programme button C .
Each time the button is pressed, the set value increases by one level; when the value of 
 has been reached, the
display jumps back to 
 (of f).
Press ST ART button 8, the set value
is saved.
Close the door .
Switching  off the appliance
Short  time after the end of the programme:
Open the door .
Switch off ON/OFF switch 1.
Turn of f the tap (not applicable
if  Aqua-Stop fitted).
Remove the utensils when they have cooled down.
Warning
At the end of the programme please open the door fully and not partially when emptying the dishwasher . Any escaping
water vapour could damage sensitiveworktops. Interrupting  the programme
Open the door .
Switch of f ON/OFF switch 1. 
The LEDs go out. The programme is saved. If the door was opened on an appliancewhich has a warm water connectionor is heated, first leave the door ajarfor several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to springopen or water to run out of theappliance.
T o continue the programme, switch
on the ON/OFF switch 
1 again.
Close the door . Terminating
 the programme
(Reset)
Open  the door .
Press ST ART button 8 for
approx 3 sec. 
 is indicated
on the digital display 
9.
Close the door .
The programme sequence lasts approx. 1 min.
 is indicated on the digital
display 
9 (buzzer sounds).
Open the door .
Switch off ON/OFF switch 1.
Close the door .
Changing  the programme
When  the ST ART button 
8 has been
pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (reset). Intensive  drying
The  final rinse uses a higher temperature
which improves the drying result. The running time may increase slightly .
(Caution if utensils are delicate!)
Open the door .
Switch on ON/OFF switch 1.
Hold down programme button A
and press ST ART button 
8 until on
the digital display 
 is indicated.
Release both buttons. The LED for button 
A  flashes and
the digital display displays the factory setting 
.
Press programme button A  until the
factory set value 
 is indicated on
the digital display 9.
T o change the setting,
Press the button C  to switch
intensive drying on 
 or of f .
Press ST ART button 8.
The set value is saved.
Close the door .
          
						

							en
18 Maintenance
 and care
A  regular inspection and maintenance of
your machine will help to prevent faults. This saves time and prevents problems. Overall  condition
of the machine
Check  spray arm for grease and
limescale deposits.
If you find such deposits:
Fill detergent dispenser with detergent. Start the appliance without utensils inthe programme with the highest rinsingtemperature.
Clean the appliance with detergents/appliance cleaners which are particularlysuitable for use with dishwashers.
Regularly clean door seal with a damp cloth.
Never use a steam cleaner to clean your dishwasher . The manufacturer is not liable
for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate.Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: T o prevent
corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
Warning
Never use other chlorinated household detergents! Health hazard! Salt  and rinse-aid
Check  the refill indicators 4 and 5.
If required, refill salt and/or rinse-aid. Filters The filters 
26
 keep large foreign objects
in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter ,
a flat fine filter and a microfilter .
After each washing cycle check the filters for residue.
Unscrew filter cylinder as illustrated and take out filter system.
Remove any residue and clean filters under running water.
Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
   
						

							en19
Spray
 arms
Limescale  and contaminants in the rinsing
water may block nozzles and bearings on the spray arms 
23  and 24.
Check outlet nozzles on the spray arms for blockages.
Unscrew the upper spray arm 23 .
Remove the lower spray arm 24
upwards.
Clean spray arms under running water .
Re-engage or screw on spray arms. Waste
 water pump
Large  food remnants in the rinsing water
not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter .
In this case:
First disconnect the appliance from the power supply .
Remove the filters 26.
Scoop out water , use a sponge
if required.
Using a spoon, prise of f pump cover
(as illustrated) until it clicks, then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards.
Check inner compartment and remove any foreign objects.
Place cover in the original position, press down and engage.
Install filters.
    
						

							en
20 Troubleshooting
Experience has shown that you can rectify most faults which occur in daily operationwithout calling customer service. Obviously this will save on costs and ensure that the machine is quickly available again. The following overview should help you locate the causes of faultswhich may occur .
Warning
If fault code  (E01 to E30)  is indicated on
the digital display 
9, first disconnect the
appliance from the power supply .
Y ou can rectify certain faults yourself
(see following fault description), for all other faults please contact customer service and state the indicated fault  E:XX.
Warning
Remember: Repairs may be carried out by technicians only . If a component has to be
replaced, ensure that only original spareparts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the userat considerable risk. ...  when the appliance is
switched on
The  appliance does not start.
The mains fuse has tripped.
The appliance plug has not been inserted.
The appliance door has not been shut properly .
...  on the appliance
Lower  spray arm rotates sluggishly .
Spray arm blocked. ...
 changing settings
A setting cannot be changed,
a programme starts.
W rong programme button pressed.
T erminate the programme
(see chapter entitled ªT erminating
the programme (Reset)º) and start all over again.
Y ou did not wait until programme
ended.
Cover on the detergent dispenser cannot be closed.
Detergent dispenser overfilled or mechanism blocked by sticky detergent residue.
Detergent residue in the detergent 
dispenser.
Dispenser was damp when filled.
ªcheck water supplyº 3 display
lights up.
T ap turned of f.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked.
Switch of f the appliance and
pull out the mains plug.
T urn of f the tap.
Clean filter in the supply hose.
Reconnect power supply .
Turn on the tap.
Switch on the appliance.