Siemens Sn 65e008 Operating Instructions

							Fault, what to do?en
31
 
The door is difficult  
to open.
Child-proof lock is activated. Deactivate childproof lock
. (See instructions 
for use at the back)
Door cannot be closed. Door lock has been activated. Cl ose door with increased force.
Door cannot be closed due to  
installation. Check appliance installation: Door or 
attached parts must close without  
obstruction.
Cover on the detergent 
dispenser cannot be  
closed. Detergent dispenser or cover  
guide blocked by sticky detergent  
residue. Remove detergent residue.
Detergent residue  
in the detergent dispenser  
or in the tablet collecting  
tray. Spray arms blocked by utensils,  
therefore detergent is not rinsed  
out.
Ensure that the spray arms can rotate freely.
The detergent dispenser was 
damp when filled. Pour detergent into the dry detergent 
dispenser only.
Appliance stops 
in the programme or  
programme is interrupted. Door not closed properly. Close the door. 
Do not place utensils or fragrance  
dispenser in the tablet collecting  
tray. 
Top basket presses against inner  
door and prevents door from  
being closed securely. Check whether rear panel is being pressed  
in, e.g. by socket or by hose holder which  
has not been removed.
Power and/or water supply 
interrupted. Restore power and/or water supply.
Filling valves making 
striking noises. Depends on domestic installation, 
as appliance is not defective. No 
effect on appliance function. No remedial action possible.
Knocking or rattling noise. Spray arm strikes the utensil s, 
utensils not positioned correctly. Position utensils so that the spray arms do  
not strike the utensils.
If there is a low load, the water 
jets strike the washing tank  
directly. Load the appliance with more utensils or  
distribute the utensils more evenly  
in the dishwasher.
Light utensils move during 
the wash cycle. Arrange light utensils securely.
Unusual foam formation. Handwash liquid in the rinse ai d 
dispenser. Immediately refill rinse aid dispenser with  
rinse aid.
Rinse aid spilled. Remove rinse aid with a cloth.
Fault Cause Remedial action
 
						

							enCustomer service
32
4 Customer serviceCustomer service
If you are unable to rectify the fault,  
please contact your customer service.  
We always find a suitable solution, even  
to avoid unnecessary visits  
by technicians. Contact information  
for your nearest customer service can  
be found on the back of these  
instructions for use or on the enclosed  
customer service list. When calling,  
please state the appliance number (E- 
Nr. = 1) and the production number  
(FD = 2) which can be found on the  
rating plate 92 on the appliance door.
Rely on the competence of the manufa 
cturer.  Contact us. You can therefore be 
sure that the repair is carried out  
by trained service technicians who carry  
original spare parts for your domestic  
appliances. 
5 Installation and 
connection
Installation and connection
The dishwasher must be connected  
correctly, otherwise it will not function 
properly. The specifications for the inlet  
and outlet as well as the electrical  
connected loads must correspond with 
the required criteria as  
specified in the following paragraphs  
or in the installation instructions. 
Install the appliance in the correct  
sequence: 
1. Checking appliance on delivery
2. Installing the appliance
3. Waste water connection
4. Fresh water connection
5. Electrical connection
Product package 
If you have any complaints, contact  
the dealer where you purchased  
the appliance or our customer service.

						

							Installation and connectionen
33
Delivery 
Your dishwasher has been checked  
thoroughly in the factory to ensure that it  
is in working order. This may cause  
small water stains. These will disappear 
after the first wash cycle. 
Technical specifications 
Weig ht: 
max. 60 kg 
Voltage:
220–240 V, 50 Hz or 60 Hz 
Connected load: 
2.0–2.4 kW 
Fuse:
10/16 A (UK 13A) 
Power input: 
switched off 0.1 W 
not switched off 0.1 W 
Water pressure: 
at least 0.05 MPa (0.5 bar), maximum  
1 MPa (10 bar). At a higher water  
pressure: connect pressure-reducing  
valve ahead. 
Inlet rate: 
minimum 10 litres/minute 
Water temperature: 
Preferably cold water; if hot water,  
depending on type of water inlet hose,  
max. temp. 60 °C (see Fresh water  
connection).
Installation 
The required installation dimensions can  
be found in the installation instructions.  
Level the appliance with the aid of the  
height-adjustable feet. Ensure that the 
appliance is situated securely on the  
floor.

						

							enInstallation and connection
34
Fresh water connection 
1.
Connect the fresh-water connection  
to the tap according  
to the installation instructions with  
the enclosed parts. 
Ensure that the fresh-water  
connection is not kinked,  
crushed or twisted.
2. When replacing the appliance,  
always use a new water supply hose.
Water pressure: 
at least 0.05 MPa (0.5 bar), maximum  
1 MPa (10 bar). At a higher water  
pressure: connect pressure-reducing  
valve ahead. 
Inlet rate: 
minimum 10 litres/minute 
Water temperature: 
Note printing on the water inlet hose! 
If models are marked with 25°,  
the water temperature may be max. 
25 °C (cold water).  
For all other models:  
cold water preferred; hot water max.  
temperature 60 °C. Electrical connection

						

							Installation and connectionen
35
Removing the appliance 
Also observe  
the sequence of worksteps here. 
1.
Disconnect the appliance from  
the power supply.
2. Turn off the water supply.
3. Disconnect the waste water  
and fresh water connections.
4. Loosen fastening screws for the  
furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully 
pulling the hose behind. Transportation 
Empty the dishwasher and secure loose  
parts. 
Drain the appliance according  
to the following steps: 
1.
Turn on the tap.
2. Open the door.
3. Switch on ON/OFF switch (.
4. Select programme  @ with 
the highest temperature button <  
H .
5. Press START button h.
6. Close the door. 
Programme sequence starts.
7. Open door after approx. 4 minutes.
8. Press START button h 
for approx. 3 sec. 
The Cleaning display  X goes out.
9. Close the door.
The remaining programme sequence  
lasts approx. 1 minute more. (Buzzer  
sounds.)
10. Switch off ON/OFF switch  (.
11. Turn off the tap, disconnect supply 
hose and drain water.
Transport appliance upright only. 
(This prevents residual water from  
running into the machine control  
and damaging the programme  
sequence.)
Protection against frost
Pr ote
ct io
n a gain s t
 fr o
st  (
Em pty
in g
 t h
e a pplia n ce)
If the appliance is in a room where there  
is a risk of frost (e.g. holiday home), 
empty the appliance completely (see  
Transportation).

 
						

							
      



   



DownloadedfromDishWasherManualcomManuals  
						

							 


 
 




 



 


 
 
 








 



 
  
 

*9000816424* 
9000816424
 en (9210-1) 640EV