Siemens Sn 65e008 Operating Instructions

Operating the applianceen
21
End of programme 
The programme has ended when  
neither of the two displays
` orX  
is lit. 
The end of the programme is also  
indicated by an acoustic signal.  
The buzzer volume can be set in 4 
stages. Accordingly 0, 1, 2 or 3 displays  
are lit (see water hardness table).  
Factory setting: 2. This function can be 
changed as follows: 
1. Open the door.
2. Switch on ON/OFF switch (. 
3. Hold down button > P and press 
START button h until the dry 
display ` and salt...

enCleaning and maintenance
22
Intensive drying 
The final rinse uses a higher  
temperature which improves the drying  
result. The running time may increase  
slightly. (Caution if utensils are delicate!) 
1.
Open the door.
2. Switch on ON/OFF switch (. 
3. Hold down button >  P and press 
START button h until the dry 
display ` and salt refill 
indicator )* flash.
4. Release buttons.
5. Keep pressing button >  P until 
the salt refill indicator  )* and  
“Check water supply”  )2 flash.
6. Release...

Cleaning and maintenanceen
23
Filters 
The filters 
1R keep large foreign 
objects in the rinsing water away from  
the pump. These foreign objects may  
occasionally block the filters. 
The filter system consists of a coarse  
filter, a flat fine filter and a microfilter. 
1. After each washing cycle check the  
filters for residue.
2. Unscrew filter cylinder as illustrated  
and take out filter system.
3. Remove any residue and clean filters 
under running water.
4. Re-install filter system in reverse...

enFault, what to do?
24
3 Fault, what to do?Fault, what to do?
Experience has shown that you can  
rectify most faults which occur in daily  
operation yourself. This ensures that  
the machine is quickly available to you  
again. In the following overview you can  
find possible causes of malfunctions  
and helpful information for rectifying  
them. 
Note 
If the appliance stops during  
dishwashing or does not start for no  
obvious reason, first run the Abort  
programme function (Reset).  
(See...

Fault, what to do?en
25
Fault table 
Fault Cause Remedial action 
“Check water supply”  
display
)2 lights up. Supply hose kinked. Install supply hose without kink
s.
Tap turned off. Turn on the tap. 
Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min.  
when water supply is open.
Filter in the water supply blocked. Switch off the applia nce and pull out 
the mains plug. Turn off the tap. Unscrew  
water connection.  
Clean filter in the supply hose. Screw water  
connection on...

enFault, what to do?
26
Refill indicator for salt 
)* 
and/or rinse-aid  ) is lit. No rinse aid. Refill rinse aid. 
No salt. Refill with special salt. 
Sensor does not detect salt  
tablets.
Use different special salt.
Refill indicator for salt  )* 
and/or rinse-aid  ) 
is not lit. Refill indicator switched off. Activation/deactivation 
(see chapter Water 
softening system/Special salt or Rinse aid).
There is still enough special salt/ 
rinse aid available. Check refill indicator, levels.
Water is left...

Fault, what to do?en
27
Appliance interior wet after  
rinse cycle.
No appliance fault. On account of the “Condensation drying
” 
principle, water droplets are physically  
induced and required in the container. The  
humidity in the air condenses on the inner 
walls of the dishwasher, drains and is  
pumped out.
Food remnants 
on the utensils. Utensils placed too closely 
together, utensils basket  
overfilled. Arrange utensils with adequate clearance  
between them ensuring that the spray jets  
can...

enFault, what to do?
28
Detergent residue Detergent dispenser cover 
blocked by utensils and therefore  
does not open fully.  Detergent dispenser cover must not be  
obstructed by utensils. 
Do not place utensils or fragrance dispenser  
in the tablet collecting tray.
Detergent dispenser cover 
blocked by the tablet. Tablet must be inserted flat and not upright.
Tablets used in the quick or short  
programme.  
Dissolving time of the detergent  
is not reached in the selected  
short programme....

Fault, what to do?en
29
White, stubborn coatings;  
limescale on the utensils,  
container or door.
Detergent substances are  
deposited. These coatings cannot  
usually be removed with  
chemicals (appliance cleaner, ...). Change detergent brand. 
Clean appliance mechanically.
Hardness range incorrectly set or  
water hardness greater than 
8.9 mmol/l. Set water softening system according 
to instructions for use or top up salt.
3 in 1 detergent or bio/eco 
detergent not effective enough. Set water...

enFault, what to do?
30
Removable streaks on  
glasses, glasses with  
metallic appearance and  
cutlery.
Too much rinse aid. Set rinse aid amount to lower setting. 
No rinse aid added or setting too  
low.
Add rinse aid and check dosage 
(recommended setting 4-5).
Detergent residue in the final 
rinse programme section.  
Detergent dispenser cover  
blocked by utensils (cover does  
not open fully). Detergent dispenser cover must not be  
obstructed by utensils.  
Do not place utensils or fragrance...