Siemens Sn 56t552 Operating Instructions

en
21
Changing the programme
When the START button ) has been 
pressed, the programme cannot be  
changed. 
The only way a programme can be  
changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature 
which improves the drying result. The 
running time may increase slightly.  
(Caution if utensils are delicate!) 
– Open the door. 
–Switch on ON/OF F switch ( .
– Hold down programme button  # and 
press START button  ) until  •:‹ .... is 
indicated on the digital...

en
22
Filters
The filters 1j keep large foreign objects 
in the rinsing water away from the pump.  
These foreign objects may occasionally 
block the filters. 
The filter system consists of a coarse filter,  
a flat fine filter and a microfilter. 
– After each washing cycle check the  filters for residue.
– Unscrew filter cylinder as illustrated  and take out filter system.
– Remove any residue and clean filters  under running water.
– Re-install filter system in reverse  sequence and ensure that the...

en
23
The majority of  faults which could occur in  
daily operation can be rectified by the 
user. This ensures that the appliance is  
quickly available for use again. The  
following overview will help you locating 
the causes and gives helpful advise to 
eliminate them. 
Note 
If the appliance stops during dishwashing  
or does not start for no obvious reason, 
first run the Abort programme function 
(Reset).  
(See chapter entitled “Dishwashing”)
ã=Warning
If on the digital display  8 an error code...

en
24
... when the appliance is  
switched on
The appliance does not start.
– The mains fuse has tripped. 
– The appliance plug has not been inserted.
– The appliance door has not been shut  properly.
... changing settings
A setting cannot be changed, a  
programme starts. 
– Wrong programme button pressed. Terminate the programme (see chapter  
entitled “Terminating the programme 
(Reset)”) and start all over again. 
– You did not wait until programme  ended.
... on the appliance
Lower spray arm rotates...

en
25
... during the wash cycle
Unusual foam formation. 
– Handwash liquid in the rinse aid dispenser. 
Spilled rinse aid causes excessive  
frothing, therefore please remove with 
a cloth.
Appliance stops during the wash cycle. 
– Power supply interrupted. 
– Water supply interrupted. 
Filling valves making striking noises 
– Caused by the installation of the water  line and has no effect on the function  
of the machine. Remedial action is not 
possible.
Knocking/rattling noise during rinsing 
– Spray...

en
26
If the advice given does not resolve your  
problem, please contact your customer 
service. Contact details can be found on  
the back cover of this instruction manual  
or in the enclosed customer service list. 
When calling , please quote the appliance 
number (1) and the production date  
(FD = 2) which can be found on the rating  
plate 
9J on the appliance door.
Rely on the expertise of the  
manufacturer.   Call us to ensure that the 
repair will be carried out  by fully-trained  
service...

en
27
– After installing the appliance, ensure 
that the plug is easily accessible. 
(see Electrical connection)
–Some models: The plastic housing on the water  
connection contains an electric valve, 
the connecting cables are in the supply 
hose. Do not cut through this hose, 
do not immerse the plastic 
housing in water.
ã=Warning
If the appliance is not in a cavity and a  
side panel is accessible, the door hinge 
area must be covered at the side  
for reasons of safety (risk of injury).  
The covers...

en
28
Warm water connec
tio
nWarm water connection *
* depending on model 
The dishwasher can be connected to cold  
or hot water up to max. 60 °C.  
Connection to hot water is recommended  
if the hot water can be supplied 
by energetically favourable means  
and from a suitable installation, e.g. solar  
heating system with circulation line. 
This will save energy and time. 
The hot water setting ‘:‹‚  allows you 
to adjust your appliance optimally  
to operation with hot water. 
It is recommended to...

en
29
Transportation
Empty the dishwasher and secure loose  
parts. 
Drain the appliance according to the  
following steps: 
– Turn on the tap. 
– Open the door. 
–Switch on ON/OFF switch ( . The 
displays of the last selected  
programme light up.
– Select programme with the highest  temperature. 
The expected programme duration is  
indicated on the numerical display   
8 .
– Press START button  ).
– Close the door.
Programme sequence starts.
– Open door after approx. 4 minutes. 
– Press START button...