Siemens Sn 56t550 Instructions For Use

							en21
Waste
 water pump
Large  food remnants in the rinsing water
not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter .
In this case:
First disconnect the appliance from the power supply .
Remove the filters 27.
Scoop out water , use a sponge
if required.
Using a spoon, prise of f pump cover
(as illustrated) until it clicks, then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards.
Check inner compartment and remove any foreign objects.
Place cover in the original position, press down and engage.
Install filters. Troubleshooting
Experience has shown that you can rectify most faults which occur in daily operationwithout calling customer service. Obviously this will save on costs and ensure that the machine is quickly available again. The following overview should help you locate the causes of faultswhich may occur .
Warning
If fault code  (E01 to E30)  is indicated on
the digital display 
3, first disconnect the
appliance from the power supply .
Y ou can rectify certain faults yourself
(see following fault description), for all other faults please contact customer service and state the indicated fault  E:XX.
Warning
Remember: Repairs may be carried out by technicians only . If a component has to be
replaced, ensure that only original spareparts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the userat considerable risk. ...  when the appliance is
switched on
The  appliance does not start.
The mains fuse has tripped.
The appliance plug has not been inserted.
The appliance door has not been shut properly .
...  on the appliance
Lower  spray arm rotates sluggishly .
Spray arm blocked.
   
						

							en
22
...
 changing settings
A setting cannot be changed,
a programme starts.
W rong programme button pressed.
T erminate the programme
(see chapter entitled ªT erminating
the programme (Reset)º) and start all over again.
Y ou did not wait until programme
ended.
Cover on the detergent dispenser cannot be closed.
Detergent dispenser overfilled or mechanism blocked by sticky detergent residue.
Detergent residue in the detergent 
dispenser.
Dispenser was damp when filled.
ªcheck water supplyº 4 display
lights up.
T ap turned of f.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked.
Switch of f the appliance and
pull out the mains plug.
T urn of f the tap.
Clean filter in the supply hose.
Reconnect power supply .
Turn on the tap.
Switch on the appliance.
W ater is left in the appliance
at the end of the programme.
(E24)  Waste water hose is
blocked or kinked.
(E25)  Waste water pump
blocked, cover on the waste water pump is not locked inposition (see Maintenance and Care).
Filters blocked.
The programme has not yet ended. W ait until programme
ends (digital display indicates 0:00) or implement the ºResetº function.
Refill indicator for salt 5 and/or
rinse-aid 
6 is not lit.
Refill indicator/s switched of f.
Adequate salt/rinse-aid available.
 
						

							en23
...
 during the wash cycle
Unusual  foam formation
Handwash liquid in the rinse aid dispenser .
Spilled rinse-aid causes excessivefrothing, therefore please removewith a cloth.
Appliance stops during the wash cycle.
Power supply interrupted.
W ater supply interrupted.
Knocking/rattling noise during rinsing
Spray arm is striking utensils.
Utensils not arranged correctly .
Filling valves making striking noises
Caused by the installation of the water line and has no effect on the
function of the machine. Remedial action is not possible.
...  on the utensils
Food  residue on the utensils.
Utensils placed too closely together , utensils basket overfilled.
Too little detergent.
Rinse programme too weak.
Spray arm rotation obstructed.
Spray arm nozzles blocked.
Filters blocked.
Filters incorrectly inserted.
W aste water pump blocked.
Top basket on right and left not set
to same height.
T ea or lipstick residue is not
completely removed.
Detergent has inadequate bleaching ef fect.
Too low rinsing temperature.
Too little/unsuitable detergent
White stains on the utensils/glasses remain milky .
If phosphate-free detergents are used with hard tap water , white deposits may be
deposited more easily on utensils and the container walls.
T oo little/unsuitable detergent.
Too weak programme selected.
No/too little rinse-aid.
No/too little salt.
W ater softening system set to the
wrong value.
Salt dispenser lock not fastened.
Contact the detergent manufacturer ,
in particular if:
the utensils are very wet at the end of the programme.
limescale forms.
Dull, discoloured glasses, film cannot be washed off.
Unsuitable detergent.
Glasses not dishwasher-proof.
Streaks on glasses and cutlery ,
glasses have metallic appearance.
T oo much rinse-aid.
Plastic parts discoloured.
Too little/unsuitable detergent.
Too weak programme selected.
Rust spots on the cutlery .
Cutlery not rust-resistant.
Salt content in the rinsing water too high, as salt dispenser lock not fastened firmly or salt was spilled while being refilled.
Utensils not dry.
Appliance door opened too early and utensils taken out too early .
Programme selected without drying.
Too little rinse-aid.
 
						

							en
24 Customer
 service
If  you are unable to rectify the fault, please
contact your customer service. Y our nearest customer service centre can
be found in the customer service list.When calling customer service, please quote the appliance number (1) and the FD number (2) which can be found on the rating plate 
33 on the appliance door .
FD
1 2
Warning
Please note that a visit by a customer service technician to repair a malfunctionor one of the described faults will not be free of charge  even during the warranty
period. Installation
The dishwasher must be connected correctly , otherwise it will not function
properly . The specifications for the inlet
and outlet as well as the electricalconnected loads must correspond with the required criteria as specified in the following paragraphs or in the installationinstructions. Install the appliance in the correct sequence:
Checking appliance on delivery
Installing the appliance
W aste-water connection
Fresh-water connection
Electrical connection
Safety  instructions
Install and connect the appliance
according to the installation and assembly instructions.
Prior to installation, disconnect the dishwasher from the power supply .
Ensure that the protective conductor system of the domestic supply has been correctly installed.
The electrical connection conditions must correspond with the specificationson the dishwasher rating plate.
If the power cord of this appliance is damaged, it must be replaced witha particular power cord. To prevent injury , the power cord may
be replaced by customer service only .
If the dishwasher is installed in a high- sided unit, the unit must be secured
properly.
Install built-under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure
stability.
 
						

							en25
Do not install the appliance near heat sources (radiators, heat storage tanks,cookers or other appliances which generate heat) and do not install under a hob.
After installing the appliance, ensure that the plug is easily accessible.
Some models: The plastic housing on the water connection contains an electric valve,the connecting cables are in the supply hose. Do not cut through this hose, do not immerse the plastic housing in water .
Warning
If the appliance is not in a cavity and a side panel is accessible, the door hingearea must be covered at the side for reasons of safety (risk of injury). The covers are available as optional accessories from customer service or specialist outlets. Delivery Y our dishwasher has been checked
thoroughly in the factory to ensure that it is in working order . This may cause small
water stains. These will disappear after thefirst wash cycle. Installation The required installation dimensions can be found in the installation instructions.Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor .
A built-under or integrated appliance which is installed subsequently as a free-standing appliance must be secured to prevent it from overturning,e.g. by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards.
The appliance can easily be installed in a fitted kitchen between wooden andplastic walls. If the plug is not freely accessible following installation, an allpole disconnector with a contactopening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety regulations.
Waste-water  connection
The required work sequence can be
found in the installation instructions. If required, fit a siphon with an drainage connection.
Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainageto prevent the waste water from flowing out!
Fresh-water  connection
Connect the fresh-water connection
to the tap according to the installation instructions with the enclosed parts. Ensure that the fresh-water connection is not kinked, crushed or twisted.
When replacing the appliance, always use a new water supply hose.
W ater pressure:
at least 0.05 MPa (0.5 bar), maximum1 MPa (10 bar). At a higher water pressure: connect pressure-reducingvalve ahead. Inlet rate: minimum 10 litres/minuteW ater temperature:
cold water preferred; hot water max. temp. 60  C.
 
						

							en
26
Electrical
 connection
Connect the appliance to an alternating
current only , ranging from 220 V to
240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earthconductor . See rating plate for required
fusing 
33 .
The socket must be near the appliance and freely accessible following installation.
The connection may be modified by technicians only .
A power cord extension may be purchased from customer service only .
Use only a residual-current-operated circuit-breaker which features the 
symbol. Only this extension guarantees compliance with the currently validregulations.
Removing  the appliance
Also  observe the sequence of worksteps
here.
Disconnect the appliance from the power supply .
Turn of f the water supply .
Disconnect the waste water and fresh water connections.
Loosen the fastening screws under the worktop.
If fitted, remove the base panel.
Pull out the appliance, carefully pulling the hose behind. Transportation
Empty the dishwasher and secure loose parts.  Drain the appliance according to the following steps:
T
urn on the tap.
Open the door .
Switch on ON/OFF switch 1. 
The displays of the last selected programme light up.
Select programme with the highest temperature.  The expected programme durationis indicated on the numerical display 
3.
Press ST ART button 10.
Close the door .
The programme starts running.
Open door after approx. 4 minutes.
Press the ST ART button 10 until
on the digital display is indicated
.
Close the door .
Open door after approx. 1 minutes. The numerical display indicates
.
Switch off appliance 1 and turn
of f the tap.
Transport appliance upright only .
(This prevents residual water from running into the machine control and damaging the programme sequence).
Protection  against frost
If  the appliance is in a room where there
is a risk of frost (e.g. holiday home),empty the appliance completely (see  Transportation).
Turn of f the tap, disconnect supply hose
and drain water .
   
						

							en27
Waste
 disposal
Both  the packaging of new appliances
and the old appliances themselves contain valuable raw materials and recyclable materials. Please dispose of the individual parts separated according to type. Please ask your dealer or inquire at your local authority about current means of disposal. Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g. >PS< polystyrene). Therefore, plastic waste can be sorted out when the appliance is being disposed of. Please follow the safety instructions under ªDelivery of your applianceº. Old  appliances
Please  follow the safety instructions under
ªDisposal of your applianceº.
This appliance is identified according
to the European guideline 2002/96/EC on waste electrical and electronic equipment ± WEEE. The guideline specifies theframework for an EU-wide valid return and re-use of old appliances.
 
						

							en
28
en Subjekt to modification
 
						

							40 Switch on the child-proof lock 
41 Open the door with child-proof lock switched on
42 Switch of f the child-proof lock Always close the appliance door completely before leaving the appliance. Only in this way can you protect your children from potential hazards.
Child-proof
 lock *
Large sheets or grilles and plates which have a diameter greater than 30 cm (gourmet plates, pasta
plates, dinner plates) can be cleaned with the aid of the spray head. T o do this, remove the top basket and insert the spray head as illustrated in the diagram.
T o ensure that the spray jet can reach all parts, arrange the baking sheets as illustrated (max. 4 baking
sheets and 2 grilles). Never operate the dishwasher without the top basket or baking sheet spray head!
Baking
 sheet spray head *
* some models
   
						

							           
AQUA-ST
OP guarantee
(does not apply to appliances without Aqua-Stop) In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions: 1.  If our Aqua-Stop system is defective and causes water damage, we will make good the damage for private users.
2.  This liability guarantee is valid for the service life of the appliance.
3.  A prerequisite for the warranty claim is that the appliancehas been correctly installed and connected with Aqua-Stop according to our instructions.  ªThis also includes the correct installation of the Aqua-Stop extension (original accessory).º Our warranty does not extend to defective feed lines or fittings up to the Aqua-Stop connection on the tap.
4.  If your appliance is fitted with Aqua-Stop, you can leave your appliance unattended during operation and leave the tapturned on afterwards. The tap should only be turned of f if you
are absent from home for a prolonged period, e.g. severalweeks holiday .
Siemens-Electroger‚te GmbHCarl-W ery-Straûe 34, 81739 M˜nchen
To  contact  us directly , use the tel. no or fax no. in the
enclosed  customer service list.
www.siemens-homeappliances.com